产品详细信息

Number of series cells 1, 2, 3, 4 Charge current (Max) (A) 5 Operating Vin (Max) (V) 24 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4 Battery charge voltage (Min) (V) 3 Battery charge voltage (Max) (V) 18.8 Absolute Vin (safety rating) (Max) ((V)) 30 Control interface I2C Features BAT temp thermistor monitoring (JEITA profile), IC thermal regulation, ICO (Input Current Optimization), IINDPM (Input current limit), Input OVP, Integrated ADC, Power Path, USB C/PD compatible, USB D+/D-/BC1.2 integrated, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Operating Vin (Min) (V) 3.6 Rating Catalog
Number of series cells 1, 2, 3, 4 Charge current (Max) (A) 5 Operating Vin (Max) (V) 24 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4 Battery charge voltage (Min) (V) 3 Battery charge voltage (Max) (V) 18.8 Absolute Vin (safety rating) (Max) ((V)) 30 Control interface I2C Features BAT temp thermistor monitoring (JEITA profile), IC thermal regulation, ICO (Input Current Optimization), IINDPM (Input current limit), Input OVP, Integrated ADC, Power Path, USB C/PD compatible, USB D+/D-/BC1.2 integrated, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Operating Vin (Min) (V) 3.6 Rating Catalog
DSBGA (YBG) 56 10 mm² 2.897 x 3.317
  • High efficient synchronous Switch Mode buck-boost charger for 1-4 cell battery
    • 750-kHz and 1.5-MHz Programmable switching frequencies
    • Efficiency optimized for charging 2s battery, 96.5% efficiency with 9-V input and 94.5% efficiency with 15-V input at 3-A ICHG
    • Charging current up to 5 A with 10-mA resolution
  • Support wide range of input sources
    • 3.6-V to 24-V Wide input operating voltage range with 30-V absolute maximum rating
    • Maximum power tracking with VINDPM up to 22 V and IINDPM up to 3.3 A
    • Detect USB BC1.2, SDP, CDP, DCP, HVDCP and non-standard adapters
  • Dual-input power mux controller for source selection
  • High level integration
    • Four switching MOSFETs and BATFET
    • Input current and charging current sensing
  • Narrow-VDC (NVDC) Power Path management
  • Power USB port from battery (USB OTG)
    • 2.8-V to 22-V OTG output voltage with 10-mV resolution to support USB-PD PPS
    • OTG Output current regulation up to 3.32 A with 40-mA resolution
  • Flexible autonomous and I2C mode for optimal system performance
  • Integrated 16-bit ADC for voltage, current and temperature monitor
  • Low battery quiescent current
    • Typical 21-µA at battery only operation
    • Typical 600 nA in Charger Shutdown Mode
  • High accuracy
    • ±0.5% Charge voltage regulation for 2s battery
    • ±5% Charge current regulation
    • ±5% Input current regulation
  • Safety
    • Thermal regulation and thermal shutdown
    • Input/battery OVP and OCP
    • Converter MOSFETs OCP
    • Charging safety timer
  • Package
    • 56-Pin 2.9mm × 3.3mm WCSP
  • High efficient synchronous Switch Mode buck-boost charger for 1-4 cell battery
    • 750-kHz and 1.5-MHz Programmable switching frequencies
    • Efficiency optimized for charging 2s battery, 96.5% efficiency with 9-V input and 94.5% efficiency with 15-V input at 3-A ICHG
    • Charging current up to 5 A with 10-mA resolution
  • Support wide range of input sources
    • 3.6-V to 24-V Wide input operating voltage range with 30-V absolute maximum rating
    • Maximum power tracking with VINDPM up to 22 V and IINDPM up to 3.3 A
    • Detect USB BC1.2, SDP, CDP, DCP, HVDCP and non-standard adapters
  • Dual-input power mux controller for source selection
  • High level integration
    • Four switching MOSFETs and BATFET
    • Input current and charging current sensing
  • Narrow-VDC (NVDC) Power Path management
  • Power USB port from battery (USB OTG)
    • 2.8-V to 22-V OTG output voltage with 10-mV resolution to support USB-PD PPS
    • OTG Output current regulation up to 3.32 A with 40-mA resolution
  • Flexible autonomous and I2C mode for optimal system performance
  • Integrated 16-bit ADC for voltage, current and temperature monitor
  • Low battery quiescent current
    • Typical 21-µA at battery only operation
    • Typical 600 nA in Charger Shutdown Mode
  • High accuracy
    • ±0.5% Charge voltage regulation for 2s battery
    • ±5% Charge current regulation
    • ±5% Input current regulation
  • Safety
    • Thermal regulation and thermal shutdown
    • Input/battery OVP and OCP
    • Converter MOSFETs OCP
    • Charging safety timer
  • Package
    • 56-Pin 2.9mm × 3.3mm WCSP

The BQ25790 is a fully integrated switch-mode buck-boost charger for 1-4 cell Li-ion battery and Li-polymer battery. The integration includes 4 switching MOSFETs (Q1, Q2, Q3, Q4), input and charging current sensing circuits, the battery FET (QBAT) and all the loop compensation of the buck-boost converter. It provides high power density and design flexibility to charge batteries across the full input voltage range for USB Type-C™ and USB power delivery (USB-PD) applications such as smart phone, tablet and other portable devices.

The charger supports the narrow VDC power path management, in which the system is regulated at a voltage slightly higher than the battery voltage, but not drop below the minimum system voltage. The system keeps operating even when the battery is completely discharged or removed. When load power exceeds input source rating, the battery gets into supplement mode and prevents the input source from being overloaded and the system from crashing.

The device charges a battery from a wide range of the input sources including legacy USB adapter to high voltage USB PD adapter and traditional barrel adapter. The charger automatically sets converter to be buck, boost or buck-boost configurations based on input voltage and battery voltage without the host control. The dual input source selector manages the power flowing from two different input sources. The inputs selection is controlled by the host through I2C with default source #1 (VAC1) as the primary input and the source #2 (VAC2) as the secondary input.

To support fast charging using adjustable high voltage adapter, the device provides D+/D- handshake. The device is compliant with USB 2.0 and USB 3.0 power delivery specification with input current and voltage regulation. In addition, the Input Current Optimizer (ICO) allows the detection of maximum power point of an unknown input source.

Besides the I2C host controlled charging mode, this charger also supports autonomous charging mode. After power up, the charging is enabled with default register settings. The device can complete a charging cycle without any software engagements. It detects battery voltage and charges the battery in different phases: trickle charging, pre-charging, constant current (CC) charging and constant voltage (CV) charging. At the end of the charging cycle, the charger automatically terminates when the charge current is below a pre-set limit (termination current) in the constant voltage phase. When the full battery falls below the recharge threshold, the charger will automatically start another charging cycle.

In the absence of input sources, this device supports USB On-the-Go (OTG) function, discharging battery to generate an adjustable 2.8V~22V voltage on VBUS with 10mV step size, which is compliant to the USB PD 3.0 specification defined programmable power supply (PPS) feature.

The charger provides various safety features for battery charging and system operations, including battery temperature negative thermistor monitoring, trickle charge, pre-charge and fast charge timers and over-voltage/over-current protections on battery and input. The thermal regulation reduces charge current when the junction temperature exceeds a programmable threshold. The STAT output of the device reports the charging status and any fault conditions. The PG output indicates if a good power source is present. The INT pin immediately notifies host when fault occurs.

The device also provides a 16-bit analog-to-digital converter (ADC) for monitoring charge current and input/battery/system (VAC, VBUS, BAT, SYS, TS) voltages.

It is available in a 56-pin 2.9mm × 3.3mm WCSP package.

The BQ25790 is a fully integrated switch-mode buck-boost charger for 1-4 cell Li-ion battery and Li-polymer battery. The integration includes 4 switching MOSFETs (Q1, Q2, Q3, Q4), input and charging current sensing circuits, the battery FET (QBAT) and all the loop compensation of the buck-boost converter. It provides high power density and design flexibility to charge batteries across the full input voltage range for USB Type-C™ and USB power delivery (USB-PD) applications such as smart phone, tablet and other portable devices.

The charger supports the narrow VDC power path management, in which the system is regulated at a voltage slightly higher than the battery voltage, but not drop below the minimum system voltage. The system keeps operating even when the battery is completely discharged or removed. When load power exceeds input source rating, the battery gets into supplement mode and prevents the input source from being overloaded and the system from crashing.

The device charges a battery from a wide range of the input sources including legacy USB adapter to high voltage USB PD adapter and traditional barrel adapter. The charger automatically sets converter to be buck, boost or buck-boost configurations based on input voltage and battery voltage without the host control. The dual input source selector manages the power flowing from two different input sources. The inputs selection is controlled by the host through I2C with default source #1 (VAC1) as the primary input and the source #2 (VAC2) as the secondary input.

To support fast charging using adjustable high voltage adapter, the device provides D+/D- handshake. The device is compliant with USB 2.0 and USB 3.0 power delivery specification with input current and voltage regulation. In addition, the Input Current Optimizer (ICO) allows the detection of maximum power point of an unknown input source.

Besides the I2C host controlled charging mode, this charger also supports autonomous charging mode. After power up, the charging is enabled with default register settings. The device can complete a charging cycle without any software engagements. It detects battery voltage and charges the battery in different phases: trickle charging, pre-charging, constant current (CC) charging and constant voltage (CV) charging. At the end of the charging cycle, the charger automatically terminates when the charge current is below a pre-set limit (termination current) in the constant voltage phase. When the full battery falls below the recharge threshold, the charger will automatically start another charging cycle.

In the absence of input sources, this device supports USB On-the-Go (OTG) function, discharging battery to generate an adjustable 2.8V~22V voltage on VBUS with 10mV step size, which is compliant to the USB PD 3.0 specification defined programmable power supply (PPS) feature.

The charger provides various safety features for battery charging and system operations, including battery temperature negative thermistor monitoring, trickle charge, pre-charge and fast charge timers and over-voltage/over-current protections on battery and input. The thermal regulation reduces charge current when the junction temperature exceeds a programmable threshold. The STAT output of the device reports the charging status and any fault conditions. The PG output indicates if a good power source is present. The INT pin immediately notifies host when fault occurs.

The device also provides a 16-bit analog-to-digital converter (ADC) for monitoring charge current and input/battery/system (VAC, VBUS, BAT, SYS, TS) voltages.

It is available in a 56-pin 2.9mm × 3.3mm WCSP package.

下载

您可能感兴趣的相似产品

open-in-new 比较产品
功能与比较器件相同但引脚有所不同。
BQ25792 正在供货 具有双输入选择器和 USB PD 3.0 OTG 输出的 I2C 控制型 1 节至 4 节电池 5A 降压/升压充电器 This product is in a WQFN package

设计和开发

如需其他信息或资源,请查看下方列表,点击标题即可进入详情页面。

评估板

BQ25790EVM — BQ25790EVM

BQ25790EVM 评估模块 (EVM) 是一款组装完备且经过测试的电路,用于评估 BQ25790 器件。BQ25790 是一款旨在用于 1-4 节锂离子和锂聚合物电池的集成式开关模式降压/升压电池充电管理器件。充电器采用窄 VDC 架构 (NVDC),即使电池完全放电,也能将系统调节至最小值。BQ25790 具有 USB 输入源检测、双输入源选择功能,支持 USB OTG,并且集成了一个 16 位多通道模数转换器 (ADC),是一套完整的充电解决方案。
TI.com 無法提供
应用软件和框架

BQSTUDIO-TEST Battery Management Studio (bqStudio) 软件 – 未测试版本下载

Battery Management Studio (bqStudio) offers a full suite of robust tools to assist with the process of evaluating, designing with, configuring, testing, or otherwise utilizing TI Battery management products. This includes features that provide full access to registers and data memory including (...)

支持的产品和硬件

支持的产品和硬件

产品
电池监测器和平衡器
BQ769142 适用于锂离子、锂聚合物和磷酸铁锂电池的 3 节至 14 节串联高精度电池监控器和保护器 BQ76942 适用于 3 节至 10 节串联电池的多节电池监控器和保护器 BQ76952 适用于锂离子、锂聚合物和磷酸铁锂电池的 3 节至 16 节串联高精度电池监控器和保护器
电池充电器 IC
BQ24800 支持混合动力升压和电池升压模式的 SMBus 1 至 4 节降压电池充电控制器 BQ25720 具有电源路径和 USB-C® PD OTG 的 SMBus 1-4 节电池 NVDC 降压/升压电池充电控制器 BQ25723 具有电源路径和 USB-C® PD OTG 的 I²C 1-4 节电池 NVDC 降压/升压电池充电控制器 BQ25731 具有 USB type-C PD 支持的 I2C 1 至 5 节 NVDC 降压/升压电池充电控制器 BQ25790 集成式、NVDC、5A、1 至 4 节开关模式降压/升压电池充电器 BQ25792 具有双输入选择器和 USB PD 3.0 OTG 输出的 I2C 控制型 1 节至 4 节电池 5A 降压/升压充电器
电池电量监测
BQ27220 具有预编程化学成分的单节电池组/系统侧 CEDV 电池电量监测计 BQ27320 单节电池组/系统侧 CEDV 电池电量监测计 BQ27425-G1 具有直接电池连接功能的系统侧 Impedance Track™ 电量监测计 | 电池电量监测计 BQ27425-G2A 适用于钴酸锂电池的系统侧 Impedance Track™ 电量监测计 BQ27425-G2B 适用于锰酸锂电池的系统侧 Impedance Track™ 电量监测计 BQ27510-G3 系统侧 Impedance-Track 电量监测计,可提供 32 字节的用户可编程数据闪存 BQ27520-G4 具有集成 LDO 的系统侧 Impedance Track™ 电量监测计 BQ27530-G1 具有直接电池连接功能的系统侧 Impedance Track 电量监测计 BQ27531-G1 适用于 bq2419x 充电器控制器的电池管理单元 Impedance Track™ 电量监测计 BQ27532-G1 适用于 bq2425x 充电器的电池管理单元 Impedance Track™ 电量监测计 BQ27541-G1 带集成 LDO 的电池组侧 Impedance Track™ 电池电量监测计 BQ27541-V200 用于电池组集成的单节锂离子电池电量监测计;固件升级到 BQ27541 BQ27542-G1 采用 SON 封装的单节电池 Impedance Track™ 电池组侧电量监测计 BQ27545-G1 单节电池、电池组侧、Impedance Track™ 电量监测计 BQ27546-G1 采用 DSBGA 封装的单节电池 Impedance Track™ 电池组侧电量监测计 BQ27621-G1 具有动态电压相关性的系统侧电量监测计,电池电量监测计 BQ27741-G1 带集成保护器的电池组侧 Impedance Track™ 电量监测计 BQ27742-G1 具有集成保护功能的单节锂离子电池电量监测计 | 电池电量监测计 BQ27Z561 适用于 1 节电池的 Impedance Track™ 集成电路电量计解决方案 BQ27Z746 Pack-side, single-cell Impedance Track™ technology fuel gauge with integrated protector BQ28Z610 适用于 1-2 节串联电池组并具有集成保护器的电池电量监测计 BQ34110 集成了极少放电型模块的多化合物高电池节数电池电量监测计 BQ34210-Q1 通过汽车级认证的单节电池系统侧 CEDV 电量监测计 BQ34Z100-G1 多化合物 Impedance Track™ 独立电量监测计 | 电池电量监测计 BQ35100 用于不可充电电池(锂原)的电池电量监测计和放电结束监测计 BQ4050 1 至 4 节串联 CEDV 电池电量监测计 BQ40Z50 1 至 4 节串联锂离子电池组管理器 | 电池电量监测计 BQ40Z50-R1 支持涡轮模式 1.0 的 1 至 4 节串联锂离子电池组管理器 BQ40Z50-R2 支持涡轮模式 2.0 的 1 至 4 节串联锂离子电池组管理器 BQ40Z60 完整的多节电池管理器 | 电池电量监测计 BQ40Z80 采用 Impedance Track™ 电量监测技术的 2 节至 7 节电池组管理器 BQ78350 采用 IMPEDANCE TRACK™ 的符合 SBS 1.1 的电量监测计 BQ78350-R1 CEDV 锂离子电池电量监测计和电池管理控制器 BQ78Z100 适用于 1 至 2 节电池的 Impedance Track™ 电池电量监测计
硬件开发
MKST-3P-ALT-EV2300 EV2300 alternative for use with BQMTESTER and ADVANCED-BQMTESTER
Software
BQ40Z50-R3-DEVICE-FW BQ40Z50-R3 器件固件:1-4 节锂离子电池组管理器 | 电池电量检测计
下载选项
应用软件和框架

BQSTUDIO-STABLE Battery Management Studio (bqStudio) 软件 – 针对 BQ 系列 TI 电池电量监测计的稳定版本下载

Battery Management Studio (bqStudio) offers a full suite of robust tools to assist with the process of evaluating, designing with, configuring, testing, or otherwise utilizing TI Battery management products. This includes features that provide full access to registers and data memory including (...)

支持的产品和硬件

支持的产品和硬件

产品
电池监测器和平衡器
BQ76942 适用于 3 节至 10 节串联电池的多节电池监控器和保护器 BQ76952 适用于锂离子、锂聚合物和磷酸铁锂电池的 3 节至 16 节串联高精度电池监控器和保护器
电池充电器 IC
BQ24800 支持混合动力升压和电池升压模式的 SMBus 1 至 4 节降压电池充电控制器 BQ25720 具有电源路径和 USB-C® PD OTG 的 SMBus 1-4 节电池 NVDC 降压/升压电池充电控制器 BQ25723 具有电源路径和 USB-C® PD OTG 的 I²C 1-4 节电池 NVDC 降压/升压电池充电控制器 BQ25731 具有 USB type-C PD 支持的 I2C 1 至 5 节 NVDC 降压/升压电池充电控制器 BQ25790 集成式、NVDC、5A、1 至 4 节开关模式降压/升压电池充电器 BQ25792 具有双输入选择器和 USB PD 3.0 OTG 输出的 I2C 控制型 1 节至 4 节电池 5A 降压/升压充电器
电池电量监测
BQ27220 具有预编程化学成分的单节电池组/系统侧 CEDV 电池电量监测计 BQ27320 单节电池组/系统侧 CEDV 电池电量监测计 BQ27425-G1 具有直接电池连接功能的系统侧 Impedance Track™ 电量监测计 | 电池电量监测计 BQ27425-G2A 适用于钴酸锂电池的系统侧 Impedance Track™ 电量监测计 BQ27425-G2B 适用于锰酸锂电池的系统侧 Impedance Track™ 电量监测计 BQ27510-G3 系统侧 Impedance-Track 电量监测计,可提供 32 字节的用户可编程数据闪存 BQ27520-G4 具有集成 LDO 的系统侧 Impedance Track™ 电量监测计 BQ27530-G1 具有直接电池连接功能的系统侧 Impedance Track 电量监测计 BQ27531-G1 适用于 bq2419x 充电器控制器的电池管理单元 Impedance Track™ 电量监测计 BQ27532-G1 适用于 bq2425x 充电器的电池管理单元 Impedance Track™ 电量监测计 BQ27541-G1 带集成 LDO 的电池组侧 Impedance Track™ 电池电量监测计 BQ27541-V200 用于电池组集成的单节锂离子电池电量监测计;固件升级到 BQ27541 BQ27542-G1 采用 SON 封装的单节电池 Impedance Track™ 电池组侧电量监测计 BQ27545-G1 单节电池、电池组侧、Impedance Track™ 电量监测计 BQ27546-G1 采用 DSBGA 封装的单节电池 Impedance Track™ 电池组侧电量监测计 BQ27621-G1 具有动态电压相关性的系统侧电量监测计,电池电量监测计 BQ27741-G1 带集成保护器的电池组侧 Impedance Track™ 电量监测计 BQ27742-G1 具有集成保护功能的单节锂离子电池电量监测计 | 电池电量监测计 BQ27Z561 适用于 1 节电池的 Impedance Track™ 集成电路电量计解决方案 BQ28Z610 适用于 1-2 节串联电池组并具有集成保护器的电池电量监测计 BQ34110 集成了极少放电型模块的多化合物高电池节数电池电量监测计 BQ34210-Q1 通过汽车级认证的单节电池系统侧 CEDV 电量监测计 BQ34Z100-G1 多化合物 Impedance Track™ 独立电量监测计 | 电池电量监测计 BQ35100 用于不可充电电池(锂原)的电池电量监测计和放电结束监测计 BQ4050 1 至 4 节串联 CEDV 电池电量监测计 BQ40Z50 1 至 4 节串联锂离子电池组管理器 | 电池电量监测计 BQ40Z50-R1 支持涡轮模式 1.0 的 1 至 4 节串联锂离子电池组管理器 BQ40Z50-R2 支持涡轮模式 2.0 的 1 至 4 节串联锂离子电池组管理器 BQ40Z60 完整的多节电池管理器 | 电池电量监测计 BQ40Z80 采用 Impedance Track™ 电量监测技术的 2 节至 7 节电池组管理器 BQ78350 采用 IMPEDANCE TRACK™ 的符合 SBS 1.1 的电量监测计 BQ78350-R1 CEDV 锂离子电池电量监测计和电池管理控制器 BQ78Z100 适用于 1 至 2 节电池的 Impedance Track™ 电池电量监测计
Software
BQ40Z50-R3-DEVICE-FW BQ40Z50-R3 器件固件:1-4 节锂离子电池组管理器 | 电池电量检测计
下载选项
应用软件和框架

TI-CHARGER-GUI — 用于 USB2ANY 和电池充电评估模块的 GUI 软件

TI-CHARGER-GUI 提供基于网络的或独立的图形用户界面,可辅助评估、设计、配置或测试电池充电器产品。该软件可实现对寄存器的全面访问,并提供一个简单接口用于发送时序命令。
封装 引脚数 下载
DSBGA (YBG) 56 了解详情

订购和质量

包含信息:
  • RoHS
  • REACH
  • 器件标识
  • 引脚镀层/焊球材料
  • MSL 等级/回流焊峰值温度
  • MTBF/时基故障估算
  • 材料成分
  • 认证摘要
  • 持续可靠性监测

推荐产品可能包含与 TI 此产品相关的参数、评估模块或参考设计。

支持与培训

视频