SPRUJ66C February   2023  – July 2026

1.   1
2.   Description
3.   Get Started
4.   Features
5.   Applications
6.   6
7. 1Evaluation Module Overview
   1. 1.1 Introduction
   2. 1.2 Kit Contents
   3. 1.3 Specification
      1. 1.3.1 Key Features
         1. 1.3.1.1 Processor
         2. 1.3.1.2 Memory
         3. 1.3.1.3 JTAG Emulator
         4. 1.3.1.4 Supported Interfaces and Peripherals
         5. 1.3.1.5 Expansion Connectors Headers to Support Application Specific Add On Boards
   4. 1.4 Device Information
8. 2Hardware
   1. 2.1 EVM Revisions and Assembly Variants
   2. 2.2 System Description
      1. 2.2.1 Board Image With Markings
      2. 2.2.2 Functional Block Diagram
      3. 2.2.3 Power Requirements
      4. 2.2.4 Power ON/OFF Procedures
         1. 2.2.4.1 Power-On Procedure
         2. 2.2.4.2 Power-Off Procedure
         3. 2.2.4.3 Power Indication LED
         4. 2.2.4.4 Power Test Points
      5. 2.2.5 AM62A Low Power SK EVM Interface Mapping
      6. 2.2.6 Peripheral and Major Component Description
         1. 2.2.6.1  Clocking
            1. 2.2.6.1.1 Peripheral Ref Clock
         2. 2.2.6.2  Reset
         3. 2.2.6.3  CSI Interface
         4. 2.2.6.4  Audio Codec Interface
         5. 2.2.6.5  HDMI Display Interface
         6. 2.2.6.6  JTAG Interface
         7. 2.2.6.7  Test Automation Header
         8. 2.2.6.8  UART Interface
         9. 2.2.6.9  USB Interface
            1. 2.2.6.9.1 USB 2.0 Type A Interface
            2. 2.2.6.9.2 USB 2.0 Type C Interface
         10. 2.2.6.10 Memory Interfaces
             1. 2.2.6.10.1 LPDDR4 Interface
             2. 2.2.6.10.2 Octal Serial Peripheral Interface (OSPI)
             3. 2.2.6.10.3 MMC Interfaces
                1. 2.2.6.10.3.1 MMC0 - eMMC Interface
                2. 2.2.6.10.3.2 MMC1 - Micro SD Interface
                3. 2.2.6.10.3.3 MMC2 - M.2 Key E Interface
             4. 2.2.6.10.4 Board ID EEPROM
         11. 2.2.6.11 Ethernet Interface
             1. 2.2.6.11.1 CPSW Ethernet PHY Default Configuration
         12. 2.2.6.12 GPIO Port Expander
         13. 2.2.6.13 GPIO Mapping
         14. 2.2.6.14 Power
             1. 2.2.6.14.1 Power Input
             2. 2.2.6.14.2 Power Supply
             3. 2.2.6.14.3 AM62A SoC Power
             4. 2.2.6.14.4 Current Monitoring
         15. 2.2.6.15 AM62A Low Power SK EVM User Setup and Configuration
             1. 2.2.6.15.1 Boot Modes
             2. 2.2.6.15.2 User Test LEDs
         16. 2.2.6.16 Expansion Headers
             1. 2.2.6.16.1 User Expansion Connector
             2. 2.2.6.16.2 MCU Connector
         17. 2.2.6.17 I2C Address Mapping
9. 3Hardware Design Files
   1. 3.1 Schematics, PCB Layout and BOM
10. 4Additional Information
    1. 4.1 Known Hardware or Software Issues
       1. 4.1.1 Issue 8 – Wake-up Through MCU and WKUP UART Not Functioning
    2. 4.2 EMC, EMI, and ESD Compliance
    3. 4.3 Trademarks
    4.     74
11. 5References
12. 6Revision History