SPRUIL8B May   2019  – May 2020 TMS320F28384D , TMS320F28384S , TMS320F28386D , TMS320F28386S , TMS320F28388D , TMS320F28388S

 

  1.   TMS320F28388D controlCARD Information Guide
    1.     Trademarks
    2. 1 Introduction
    3. 2 Hardware Quick Setup Guide
    4. 3 Errata
      1. 3.1 Warnings, Notes, and Errata
      2. 3.2 Warnings and Notes for All controlCARDs
      3. 3.3 Warnings About Specific controlCARD Revisions
    5. 4 Getting Familiar With the controlCARD
      1. 4.1 F28388D controlCARD Features
      2. 4.2 Assumed Operating Conditions
      3. 4.3 Using the controlCARD
        1. 4.3.1 Clocking Configuration
      4. 4.4 Experimentation Software
    6. 5 Special Notes
      1. 5.1 XDS100v2 Emulator and SCI (UART) Connectivity
      2. 5.2 External Connector
    7. 6 Hardware References
    8. 7 References
  2.   Revision History

4.3 Using the controlCARD

In order for the controlCARD to operate, the controlCARD’s MCU must be powered. This is most often done by inputting 5 V through the HSEC connector via an accompanying baseboard. For example, if using a docking station baseboard, 5 V DC should be input into the docking station’s J1 or J17. Then, SW1 needs to be toggled to the appropriate position.

Optionally, the MCU could also be powered via the micro-USB connector on the controlCARD (J3). Based on the way the controlCARD is used, additional hardware settings will be necessary (see Table 1).

Table 1. Emulator Switch Selections

Debug Using CCS and the On-Card XDS100v2 Emulator Debug Using CCS and an External Emulator via the Baseboard Standalone (Boot From FLASH or Other Boot Mode)
S1:A Position 1: ON (right) Position 1: OFF (left) Position 1: OFF (left)
J1:A Connect a mini USB cable between J1:A and your computer.
In CCS, use this target configuration: TMS320F28388D device with an XDS100v2 emulator. 		--- ---
S2 Position 1: OFF (left- Logic 1)
Position 2: ON (right- Logic 0)
Putting the C2000 device into WaitMode can reduce the risk of connectivity issues. 		Position 1: OFF (right- Logic 1)Position 2: ON (left- Logic 0) - Putting the C2000 device into Wait Mode can reduce the risk of connectivity issues. Set S1 as desired
Baseboard’s JTAG connector (J2 on Docking Station) --- Connect an external emulator. ---

Code Composer Studio is an Integrated Development Environment (IDE) used to debug and develop software for the C2000 series of MCUs. It can be downloaded from the following link: http://www.ti.com/tool/ccstudio.

The following PDF documents are provided,as part of C2000Ware, to describe where each of the F2838x MCU’s pins will appear on the controlCARD connector/docking station:

  • TMDSCNCD28388D_180cCARD_map– tells where each MCU pin will go on the HSEC controlCARD connector or the 120/180-pin controlCARD docking station.
  • TMDSCNCD28388D_100DIM_map – tells where each MCU pin will go to on the DIM100 controlCARD connector or the DIM100 docking station. This assumes that the TMDSADAP180TO100 adapter card is used.

More information on the controlCARD docking station can be found at the following location:

  • <install directory>\c2000\C2000Ware_x_xx_xx_xx\boards\controlCARDs\TMDSCNCD28388D\Rx_x