ZHCSC49A March   2014  – May 2014 TPS92511

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用范围
  3. 3 说明
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Handling Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Pulse Level Modulation (PLM) Control
      2. 7.3.2  Pulse Level Modulation (PLM) Operaion Principles
      3. 7.3.3  PLM Control enable Common-Anode Low-Side Sensing (CALS)Technique to Save Wiring
      4. 7.3.4  Internal Regulator
      5. 7.3.5  Setting The Switching Frequency
      6. 7.3.6  Setting The LED Current
      7. 7.3.7  Integrated MOSFET
      8. 7.3.8  Inductor Selection
      9. 7.3.9  Integrated MOSFET Current Limit
      10. 7.3.10 PWM Dimming Control
      11. 7.3.11 Analog Dimming
      12. 7.3.12 High Voltage Buck Configuration
      13. 7.3.13 Thermal Foldback
      14. 7.3.14 EMI Consideration
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation with VIN < 4.5 V (minimum VIN)
      2. 7.4.2 Operation with DIM control
      3. 7.4.3 Linear Mode
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 TPS92511 LED driver for 12 LEDs at 0.5A
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
  9. 9 Power Supply Recommendation
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
      1. 10.2.1 Thermal Consideration
  11. 11器件和文档支持
    1. 11.1 Trademarks
    2. 11.2 Electrostatic Discharge Caution
    3. 11.3 Glossary
  12. 12机械封装和可订购信息

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • DDA|8
散热焊盘机械数据 (封装 | 引脚)
订购信息

5 Pin Configuration and Functions

DDA (SO THERMAL PAD) PACKAGE
8 PINS
(TOP VIEW)
pinout_dda8_snvs901.gif

Pin Functions

PIN DESCRIPTION
NAME NO.
DIM 6 PWM Dimming Control. Apply logic level PWM signal to this pin dims the LED string. This pin is internally pulled up.
FS 5 Switching Frequency Setting. An external resistor RFS connecting the FS pin to ground programs the switching frequency from 50 kHz to 500 kHz.
GND 4 Analog Signal Ground.
IADJ 3 Average LED Current Setting. An external resistor RIADJ connecting the IADJ pin to ground programs the average LED current.
LX 7 Integrated MOSFET Drain. Internally connected to the drain of the integrated MOSFET. Connect this pin to the output inductor and anode of the Schottky diode.
PGND 2 Power Ground. Must be connected to the GND pin for normal operation. The PGND and GND pins are not internally shorted.
VCC 1 Internal Regulator Output. Typically regulated to 5.4 V. Connect a capacitor of larger than 1 µF between the VCC and GND pins.
VIN 8 Input Voltage. Supply pin to the device. The input voltage range is from 4.5 V to 65 V.
Thermal pad Thermal Connection Pad. Connect to a ground plane for heat dissipation.