ZHCS936A May   2012  – February 2019 TPS53014

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
    1.     Device Images
      1.      典型应用
  4. 修订历史记录
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Recommended Operating Conditions
    3. 6.3 Thermal Information
    4. 6.4 Electrical Characteristics
    5. 6.5 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 PWM Operation
      2. 7.3.2 Auto-Skip Eco-Mode Control
      3. 7.3.3 Drivers
      4. 7.3.4 5-Volt Regulator
      5. 7.3.5 Soft Start and Pre-Biased Soft Start
      6. 7.3.6 Overcurrent Protection
      7. 7.3.7 Over/Undervoltage Protection
      8. 7.3.8 UVLO Protection
      9. 7.3.9 Thermal Shutdown
  8. Application and Implementation
    1. 8.1 Typical Application
      1. 8.1.1 Detailed Design Procedure
        1. 8.1.1.1 Component Selection
          1. 8.1.1.1.1 Inductor
          2. 8.1.1.1.2 Output Capacitor
          3. 8.1.1.1.3 Input Capacitor
          4. 8.1.1.1.4 Bootstrap Capacitor
          5. 8.1.1.1.5 VREG5 Capacitor
          6. 8.1.1.1.6 Choose Output Voltage Resistors
  9. Layout
    1. 9.1 Layout Guidelines
  10. 10器件和文档支持
    1. 10.1 接收文档更新通知
    2. 10.2 社区资源
    3. 10.3 商标
    4. 10.4 静电放电警告
    5. 10.5 术语表

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Overcurrent Protection

TPS53014 has a cycle-by-cycle over current limit feature. The over current limits the inductor valley current by monitoring the voltage drop across the low-side MOSFET RDS(on) during the low-side driver on-time. If the inductor current is larger than the over current limit (OCL), the TPS53014 delays the start of the next switching cycle until the sensed inductor current falls below the OCL current. MOSFET RDS(on) current sensing is used to provide an accuracy and cost effective solution without external devices. To program the OCL, a resister should be connected between DRVL and PGND. The recommended values are given inTable 1.

Table 1. OCL Resistor Values

RESISTER VALUE ( kΩ) Vtrip (V)
6.8 0.050
11 0.087
18 0.125
27 0.174
39 0.224
56 0.274
75 0.336

IOCL is determined by Equation 3.

Equation 3. TPS53014 eq3_slvsbf1.gif

The trip voltage is set between 0.05 V to 0.336 V over all operational temperature, including the 4000ppm/°C temperature slope compensation for the temperature dependency of the RDS(on). If the load current exceeds the overcurrent limit, the voltage will begin to drop. If the over-current conditions continues the output voltage will fall below the under voltage protection threshold and the TPS53014 will shut down.