ZHCSTJ5A October   2023  – February 2024 TPS274C65CP

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Diagrams
      2. 8.3.2 Programmable Current Limit
      3. 8.3.3 Protection Mechanisms
        1. 8.3.3.1 Over-current Protection
        2. 8.3.3.2 Short-Circuit Protection
          1. 8.3.3.2.1 VS During Short-to-Ground
        3. 8.3.3.3 Thermal Shutdown Behavior
        4. 8.3.3.4 Inductive-Load Switching-Off Clamp
        5. 8.3.3.5 Inductive Load Demagnetization
        6. 8.3.3.6 Thermal Shutdown
        7. 8.3.3.7 Undervoltage Protection on VS (UVP)
        8. 8.3.3.8 Undervoltage Lockout on Low Voltage Supply (VDD_UVLO)
        9. 8.3.3.9 Power-Up and Power-Down Behavior
      4. 8.3.4 Diagnostic Mechanisms
        1. 8.3.4.1 Fault Indication
        2. 8.3.4.2 Short-to-Battery and Open-Load Detection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Off
      2. 8.4.2 Active
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 IEC 61000-4-5 Surge
        2. 9.2.2.2 Loss of GND
        3. 9.2.2.3 Paralleling Channels
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 静电放电警告
    6. 10.6 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.3.3.7 Undervoltage Protection on VS (UVP)

The device monitors the supply voltage VS to prevent unpredicted behaviors in the event that the supply voltage is too low. When the supply voltage falls down to VS_UVPF, the switches shut off. If the voltage is still above the VS,UVLOR, the VS_FLT pin is pulled low to signal the supply fault if the supply. When the supply rises up to VS_UVPR, the device turns back on and VS_FLT is cleared.

Fault is not indicated on the STx pin during an UVLO event. During an initial ramp of VVS from 0 V at a ramp rate slower than 1 V/ms, VENx pins must be held low until VS is above the UVP threshold. For best operation, ensure that VS has risen above UVP before setting the VENx pins to high.