ZHCSQU3A May   2004  – July 2022 SN74CB3Q16211

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. 说明(续)
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 Handling Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Electrical Characteristics
    5. 7.5 Switching Characteristics
    6. 7.6 Typical Characteristics
  8. Parameter Measurement Information
  9. Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 接收文档更新通知
    3. 9.3 支持资源
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 术语表
  10. 10Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • DGG|56
  • DL|56
  • DGV|56
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)(1)
PARAMETERTEST CONDITIONSMINTYP(2)MAXUNIT
VIKVCC = 3.6 V,II = –18 mA–1.8V
IINControl inputsVCC = 3.6 V,VIN = 0 to 5.5 V±1µA
IOZ(3)VCC = 3.6 V,VO = 0 to 5.5 V,
VI = 0
Switch OFF,
VIN = VCC or GND
±1µA
IoffVCC = 0,VO = 0 to 5.5 V,VI = 01µA
ICCVCC = 3.6 V,II/O = 0,Switch ON or OFF,
VIN = VCC or GND
13mA
∆ICC(4)Control inputsVCC = 3.6 V,One input at 3 V,Other inputs at VCC or GND30µA
ICCD(5)Per control inputVCC = 3.6 V,A and B ports open,
Control input switching at 50% duty cycle
0.150.25mA/
MHz
CinControl inputsVCC = 3.3 V,VIN = 5.5 V, 3.3 V, or 03.55pF
Cio(OFF)VCC = 3.3 V,VIN = VCC or GND,Switch OFF,
VI/O = 5.5 V, 3.3 V, or 0
45pF
Cio(ON)VCC = 3.3 V,VIN = VCC or GND,Switch ON,
VI/O = 5.5 V, 3.3 V, or 0
1012.5pF
ron(6)VCC = 2.3 V,
TYP at VCC = 2.5 V
VI = 0,IO = 30 mA58
VI = 1.7 V,IO = –15 mA59
VCC = 3 VVI = 0,IO = 30 mA56.5
VI = 2.4 V,IO = –15 mA58
VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins.
All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.
For I/O ports, the parameter IOZ includes the input leakage current.
This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.
This parameter specifies the dynamic power-supply current associated with the operating frequency of a single control input (see Figure 7-2).
Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals.