SNAS703 April   2017 LMK04828-EP

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 SPI Interface Timing
    7. 7.7 Timing Diagram
    8. 7.8 Typical Characteristics - Clock Output AC Characteristics
  8. 8 Parameter Measurement Information
    1. 8.1 Charge Pump Current Specification Definitions
      1. 8.1.1 Charge Pump Output Current Magnitude Variation vs Charge Pump Output Voltage
      2. 8.1.2 Charge Pump Sink Current vs Charge Pump Output Source Current Mismatch
      3. 8.1.3 Charge Pump Output Current Magnitude Variation vs Ambient Temperature
    2. 8.2 Differential Voltage Measurement Terminology
  9. 9 Detailed Description
    1. 9.1 Overview
      1. 9.1.1  Jitter Cleaning
      2. 9.1.2  JEDEC JESD204B Support
      3. 9.1.3  Three PLL1 Redundant Reference Inputs (CLKin0/CLKin0*, CLKin1/CLKin1*, and CLKin2/CLKin2*)
      4. 9.1.4  VCXO or Crystal Buffered Output
      5. 9.1.5  Frequency Holdover
      6. 9.1.6  PLL2 Integrated Loop Filter Poles
      7. 9.1.7  Internal VCOs
      8. 9.1.8  External VCO Mode
      9. 9.1.9  Clock Distribution
        1. 9.1.9.1 Device Clock Divider
        2. 9.1.9.2 SYSREF Clock Divider
        3. 9.1.9.3 Device Clock Delay
        4. 9.1.9.4 SYSREF Delay
        5. 9.1.9.5 Glitchless Half Step and Glitchless Analog Delay
        6. 9.1.9.6 Programmable Output Formats
        7. 9.1.9.7 Clock Output Synchronization
      10. 9.1.10 0-Delay
      11. 9.1.11 Status Pins
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 SYNC/SYSREF
      2. 9.3.2 JEDEC JESD204B
        1. 9.3.2.1 How To Enable SYSREF
          1. 9.3.2.1.1 Setup of SYSREF Example
          2. 9.3.2.1.2 SYSREF_CLR
        2. 9.3.2.2 SYSREF Modes
          1. 9.3.2.2.1 SYSREF Pulser
          2. 9.3.2.2.2 Continuous SYSREF
          3. 9.3.2.2.3 SYSREF Request
      3. 9.3.3 Digital Delay
        1. 9.3.3.1 Fixed Digital Delay
          1. 9.3.3.1.1 Fixed Digital Delay Example
        2. 9.3.3.2 Dynamic Digital Delay
        3. 9.3.3.3 Single and Multiple Dynamic Digital Delay Example
      4. 9.3.4 SYSREF to Device Clock Alignment
      5. 9.3.5 Input Clock Switching
        1. 9.3.5.1 Input Clock Switching - Manual Mode
        2. 9.3.5.2 Input Clock Switching - Pin Select Mode
        3. 9.3.5.3 Input Clock Switching - Automatic Mode
      6. 9.3.6 Digital Lock Detect
        1. 9.3.6.1 Calculating Digital Lock Detect Frequency Accuracy
      7. 9.3.7 Holdover
        1. 9.3.7.1 Enable Holdover
          1. 9.3.7.1.1 Fixed (Manual) CPout1 Holdover Mode
          2. 9.3.7.1.2 Tracked CPout1 Holdover Mode
        2. 9.3.7.2 During Holdover
        3. 9.3.7.3 Exiting Holdover
        4. 9.3.7.4 Holdover Frequency Accuracy and DAC Performance
        5. 9.3.7.5 Holdover Mode - Automatic Exit of Holdover
    4. 9.4 Device Functional Modes
      1. 9.4.1 DUAL PLL
      2. 9.4.2 0-DELAY Dual PLL
    5. 9.5 Programming
      1. 9.5.1 Recommended Programming Sequence
        1. 9.5.1.1 SPI LOCK
        2. 9.5.1.2 SYSREF_CLR
    6. 9.6 Register Maps
      1. 9.6.1 Register Map for Device Programming
    7. 9.7 Device Register Descriptions
      1. 9.7.1 System Functions
        1. 9.7.1.1 RESET, SPI_3WIRE_DIS
        2. 9.7.1.2 POWERDOWN
        3. 9.7.1.3 ID_DEVICE_TYPE
        4. 9.7.1.4 ID_PROD[15:8], ID_PROD
        5. 9.7.1.5 ID_MASKREV
        6. 9.7.1.6 ID_VNDR[15:8], ID_VNDR
      2. 9.7.2 (0x100 - 0x138) Device Clock and SYSREF Clock Output Controls
        1. 9.7.2.1 CLKoutX_Y_ODL, CLKoutX_Y_IDL, DCLKoutX_DIV
        2. 9.7.2.2 DCLKoutX_DDLY_CNTH, DCLKoutX_DDLY_CNTL
        3. 9.7.2.3 DCLKoutX_DDLYd_CNTH, DCLKoutX_DDLYd_CNTL
        4. 9.7.2.4 DCLKoutX_ADLY, DCLKoutX_ADLY_MUX, DCLKout_MUX
        5. 9.7.2.5 DCLKoutX_HS, SDCLKoutY_MUX, SDCLKoutY_DDLY, SDCLKoutY_HS
        6. 9.7.2.6 SDCLKoutY_ADLY_EN, SDCLKoutY_ADLY
        7. 9.7.2.7 DCLKoutX_DDLY_PD, DCLKoutX_HSg_PD, DCLKout_ADLYg_PD, DCLKout_ADLY_PD, DCLKoutX_Y_PD, SDCLKoutY_DIS_MODE, SDCLKoutY_PD
        8. 9.7.2.8 SDCLKoutY_POL, SDCLKoutY_FMT, DCLKoutX_POL, DCLKoutX_FMT
      3. 9.7.3 SYSREF, SYNC, and Device Config
        1. 9.7.3.1  VCO_MUX, OSCout_MUX, OSCout_FMT
        2. 9.7.3.2  SYSREF_CLKin0_MUX, SYSREF_MUX
        3. 9.7.3.3  SYSREF_DIV[12:8], SYSREF_DIV[7:0]
        4. 9.7.3.4  SYSREF_DDLY[12:8], SYSREF_DDLY[7:0]
        5. 9.7.3.5  SYSREF_PULSE_CNT
        6. 9.7.3.6  PLL2_NCLK_MUX, PLL1_NCLK_MUX, FB_MUX, FB_MUX_EN
        7. 9.7.3.7  PLL1_PD, VCO_LDO_PD, VCO_PD, OSCin_PD, SYSREF_GBL_PD, SYSREF_PD, SYSREF_DDLY_PD, SYSREF_PLSR_PD
        8. 9.7.3.8  DDLYd_SYSREF_EN, DDLYdX_EN
        9. 9.7.3.9  DDLYd_STEP_CNT
        10. 9.7.3.10 SYSREF_CLR, SYNC_1SHOT_EN, SYNC_POL, SYNC_EN, SYNC_PLL2_DLD, SYNC_PLL1_DLD, SYNC_MODE
        11. 9.7.3.11 SYNC_DISSYSREF, SYNC_DISX
        12. 9.7.3.12 Fixed Register
      4. 9.7.4 (0x146 - 0x149) CLKin Control
        1. 9.7.4.1 CLKin2_EN, CLKin1_EN, CLKin0_EN, CLKin2_TYPE, CLKin1_TYPE, CLKin0_TYPE
        2. 9.7.4.2 CLKin_SEL_POL, CLKin_SEL_MODE, CLKin1_OUT_MUX, CLKin0_OUT_MUX
        3. 9.7.4.3 CLKin_SEL0_MUX, CLKin_SEL0_TYPE
        4. 9.7.4.4 SDIO_RDBK_TYPE, CLKin_SEL1_MUX, CLKin_SEL1_TYPE
      5. 9.7.5 RESET_MUX, RESET_TYPE
      6. 9.7.6 (0x14B - 0x152) Holdover
        1. 9.7.6.1 LOS_TIMEOUT, LOS_EN, TRACK_EN, HOLDOVER_FORCE, MAN_DAC_EN, MAN_DAC[9:8]
        2. 9.7.6.2 MAN_DAC[9:8], MAN_DAC[7:0]
        3. 9.7.6.3 DAC_TRIP_LOW
        4. 9.7.6.4 DAC_CLK_MULT, DAC_TRIP_HIGH
        5. 9.7.6.5 DAC_CLK_CNTR
        6. 9.7.6.6 CLKin_OVERRIDE, HOLDOVER_PLL1_DET, HOLDOVER_LOS_DET, HOLDOVER_VTUNE_DET, HOLDOVER_HITLESS_SWITCH, HOLDOVER_EN
        7. 9.7.6.7 HOLDOVER_DLD_CNT[13:8], HOLDOVER_DLD_CNT[7:0]
      7. 9.7.7 (0x153 - 0x15F) PLL1 Configuration
        1. 9.7.7.1 CLKin0_R[13:8], CLKin0_R[7:0]
        2. 9.7.7.2 CLKin1_R[13:8], CLKin1_R[7:0]
        3. 9.7.7.3 CLKin2_R[13:8], CLKin2_R[7:0]
        4. 9.7.7.4 PLL1_N
        5. 9.7.7.5 PLL1_WND_SIZE, PLL1_CP_TRI, PLL1_CP_POL, PLL1_CP_GAIN
        6. 9.7.7.6 PLL1_DLD_CNT[13:8], PLL1_DLD_CNT[7:0]
        7. 9.7.7.7 PLL1_R_DLY, PLL1_N_DLY
        8. 9.7.7.8 PLL1_LD_MUX, PLL1_LD_TYPE
      8. 9.7.8 (0x160 - 0x16E) PLL2 Configuration
        1. 9.7.8.1 PLL2_R[11:8], PLL2_R[7:0]
        2. 9.7.8.2 PLL2_P, OSCin_FREQ, PLL2_XTAL_EN, PLL2_REF_2X_EN
        3. 9.7.8.3 PLL2_N_CAL
        4. 9.7.8.4 PLL2_FCAL_DIS, PLL2_N
        5. 9.7.8.5 PLL2_WND_SIZE, PLL2_CP_GAIN, PLL2_CP_POL, PLL2_CP_TRI
        6. 9.7.8.6 SYSREF_REQ_EN, PLL2_DLD_CNT
        7. 9.7.8.7 PLL2_LF_R4, PLL2_LF_R3
        8. 9.7.8.8 PLL2_LF_C4, PLL2_LF_C3
        9. 9.7.8.9 PLL2_LD_MUX, PLL2_LD_TYPE
      9. 9.7.9 (0x16F - 0x1FFF) Misc Registers
        1. 9.7.9.1  Fixed Register 0x171
        2. 9.7.9.2  Fixed Register 0x172
        3. 9.7.9.3  PLL2_PRE_PD, PLL2_PD
        4. 9.7.9.4  OPT_REG_1
        5. 9.7.9.5  OPT_REG_2
        6. 9.7.9.6  RB_PLL1_LD_LOST, RB_PLL1_LD, CLR_PLL1_LD_LOST
        7. 9.7.9.7  RB_PLL2_LD_LOST, RB_PLL2_LD, CLR_PLL2_LD_LOST
        8. 9.7.9.8  RB_DAC_VALUE(MSB), RB_CLKinX_SEL, RB_CLKinX_LOS
        9. 9.7.9.9  RB_DAC_VALUE
        10. 9.7.9.10 RB_HOLDOVER
        11. 9.7.9.11 SPI_LOCK
  10. 10Applications and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Digital Lock Detect Frequency Accuracy
        1. 10.1.1.1 Minimum Lock Time Calculation Example
      2. 10.1.2 Driving CLKin and OSCin Inputs
        1. 10.1.2.1 Driving CLKin Pins With a Differential Source
        2. 10.1.2.2 Driving CLKin or OSCin Pins With a Single-Ended Source
      3. 10.1.3 Using AC-Coupled Clock Outputs
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Device Selection
          1. 10.2.2.1.1 Clock Architect
          2. 10.2.2.1.2 Clock Design Tool
        2. 10.2.2.2 Device Configuration and Simulation
        3. 10.2.2.3 Device Programming
      3. 10.2.3 Application Curves
    3. 10.3 Do's and Don'ts
      1. 10.3.1 Pin Connection Recommendations
  11. 11Power Supply Recommendations
    1. 11.1 Current Consumption / Power Dissipation Calculations
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Thermal Management
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Development Support
        1. 13.1.1.1 Clock Architect
        2. 13.1.1.2 Clock Design Tool
        3. 13.1.1.3 TICS Pro
      2. 13.6   Electrostatic Discharge Caution
      3. 13.7   Glossary
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Community Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Pin Configuration and Functions

NKD Package
64-Pin WQFN
Top View
LMK04828-EP po_SNAS605.gif

Pin Functions

PIN I/O TYPE DESCRIPTION(1)
NO. NAME
1
2		 DCLKout0,
DCLKout0*		 O Programmable Device clock output 0
3
4		 SDCLKout1,
SDCLKout1*		 O Programmable SYSREF or device clock output 1
5 RESET/GPO I CMOS Device reset input or GPO
6 SYNC/SYSREF_REQ I CMOS Synchronization input or SYSREF_REQ for requesting continuous SYSREF
7, 8, 9 NC Do not connect. These pins must be left floating.
10 Vcc1_VCO PWR Power supply for VCO LDO
11 LDObyp1 ANLG LDO bypass, bypassed to ground with 10-µF capacitor.
12 LDObyp2 ANLG LDO bypass, bypassed to ground with a 0.1-µF capacitor.
13
14		 SDCLKout3,
SDCLKout3*		 O Programmable SYSREF or device clock output 3
15
16		 DCLKout2,
DCLKout2*		 O Programmable Device clock output 2
17 Vcc2_CG1 PWR Power supply for clock outputs 2 and 3
18 CS* I CMOS Chip select
19 SCK I CMOS SPI clock
20 SDIO I/O CMOS SPI data
21 Vcc3_SYSREF PWR Power supply for SYSREF divider and SYNC
22
23		 SDCLKout5,
SDCKLout5*		 O Programmable SYSREF or device clock output 5
24
25		 DCLKout4,
DCLKout4*		 O Programmable Device clock output 4
26 Vcc4_CG2 PWR Power supply for clock outputs 4, 5, 6 and 7
27
28		 DCLKout6,
DCLKout6*		 O Programmable Device clock output 6
29
30		 SDCLKout7,
SDCLKout7*		 O Programmable SYSREF or device clock output 7
31 Status_LD1 I/O Programmable Programmable status pin
32 CPout1 O ANLG Charge pump 1 output
33 Vcc5_DIG PWR Power supply for the digital circuitry
34
35		 CLKin1, CLKin1* I ANLG Reference clock Input Port 1 for PLL1
FBCLKin,
FBCLKin*		 I ANLG Feedback input for external clock feedback input (0–delay mode)
Fin, Fin* I ANLG External VCO input (external VCO mode)
36 Vcc6_PLL1 PWR Power supply for PLL1, charge pump 1, holdover DAC
37
38		 CLKin0, CLKin0* I ANLG Reference clock input port 0 for PLL1
39 Vcc7_OSCout PWR Power supply for OSCout port
40
41		 OSCout, OSCout* I/O Programmable Buffered output of OSCin port
CLKin2, CLKin2* Reference clock Input Port 2 for PLL1
42 Vcc8_OSCin PWR Power supply for OSCin
43
44		 OSCin, OSCin* I ANLG Feedback to PLL1, reference input to PLL2 — AC-coupled
45 Vcc9_CP2 PWR Power supply for PLL2 charge pump
46 CPout2 O ANLG Charge pump 2 output
47 Vcc10_PLL2 PWR Power supply for PLL2
48 Status_LD2 I/O Programmable Programmable status pin
49
50		 SDCLKout9,
SDCLKout9*		 O Programmable SYSREF or device clock 9
51
52		 DCLKout8,
DCLKout8*		 O Programmable Device clock output 8
53 Vcc11_CG3 PWR Power supply for clock outputs 8, 9, 10, and 11
54
55		 DCLKout10,
DCLKout10*		 O Programmable Device clock output 10
56
57		 SDCLKout11,
SDCLKout11*		 O Programmable SYSREF or device clock output 11
58 CLKin_SEL0 I/O Programmable Programmable status pin
59 CLKin_SEL1 I/O Programmable Programmable status pin
60
61		 SDCLKout13,
SDCLKout13*		 O Programmable SYSREF or device clock output 13
62
63		 DCLKout12,
DCLKout12*		 O Programmable Device clock output 12
64 Vcc12_CG0 PWR Power supply for clock outputs 0, 1, 12, and 13
DAP DAP GND DIE ATTACH PAD, connect to GND
(1) See Pin Connection Recommendations for recommended connections.