ZHCSUL6 February   2024 ADC12DL1500 , ADC12DL2500 , ADC12DL500

PRODUCTION DATA  

  1.   1
  2. 特性
  3. 应用
  4. 说明
  5. Pin Configuration and Functions
  6. Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: DC Specifications
    6. 5.6  Electrical Characteristics: Power Consumption
    7. 5.7  Electrical Characteristics: AC Specifications (Dual-Channel Mode)
    8. 5.8  Electrical Characteristics: AC Specifications (Single-Channel Mode)
    9. 5.9  Timing Requirements
    10. 5.10 Switching Characteristics
    11. 5.11 Timing Diagrams
    12. 5.12 Typical Characteristics - ADC12DL500
    13. 5.13 Typical Characteristics - ADC12DL1500 (1GSPS)
    14. 5.14 Typical Characteristics - ADC12DL1500 (1.5GSPS)
    15. 5.15 Typical Characteristics - ADC12DL2500 (2GSPS)
    16. 5.16 Typical Characteristics - ADC12DL2500 (2.5GSPS)
  7. Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Analog Inputs
        1. 6.3.1.1 Analog Input Protection
        2. 6.3.1.2 Full-Scale Voltage (VFS) Adjustment
        3. 6.3.1.3 Analog Input Offset Adjust
      2. 6.3.2 ADC Core
        1. 6.3.2.1 ADC Theory of Operation
        2. 6.3.2.2 ADC Core Calibration
        3. 6.3.2.3 ADC Overrange Detection
        4. 6.3.2.4 Code Error Rate (CER)
        5. 6.3.2.5 Internal Dither
      3. 6.3.3 Timestamp
      4. 6.3.4 Clocking
        1. 6.3.4.1 Noiseless Aperture Delay Adjustment (tAD Adjust)
        2. 6.3.4.2 Aperture Delay Ramp Control (TAD_RAMP)
        3. 6.3.4.3 SYSREF Capture for Multi-Device Synchronization and Deterministic Latency
          1. 6.3.4.3.1 SYSREF Position Detector and Sampling Position Selection (SYSREF Windowing)
          2. 6.3.4.3.2 Automatic SYSREF Calibration
      5. 6.3.5 LVDS Digital Interface
        1. 6.3.5.1 Multi-Device Synchronization and Deterministic Latency Using Strobes
          1. 6.3.5.1.1 Dedicated Strobe Pins
          2. 6.3.5.1.2 Reduced Width Interface With Dedicated Strobe Pins
          3. 6.3.5.1.3 LSB Replacement With a Strobe
          4. 6.3.5.1.4 Strobe Over All Data Pairs
      6. 6.3.6 Alarm Monitoring
        1. 6.3.6.1 Clock Upset Detection
      7. 6.3.7 Temperature Monitoring Diode
      8. 6.3.8 Analog Reference Voltage
    4. 6.4 Device Functional Modes
      1. 6.4.1 Dual-Channel Mode (Non-DES Mode)
      2. 6.4.2 Internal Dither Modes
      3. 6.4.3 Single-Channel Mode (DES Mode)
      4. 6.4.4 LVDS Output Driver Modes
      5. 6.4.5 LVDS Output Modes
        1. 6.4.5.1 Staggered Output Mode
        2. 6.4.5.2 Aligned Output Mode
        3. 6.4.5.3 Reducing the Number of Strobes
        4. 6.4.5.4 Reducing the Number of Data Clocks
        5. 6.4.5.5 Scrambling
        6. 6.4.5.6 Digital Interface Test Patterns and LVSD SYNC Functionality
          1. 6.4.5.6.1 Active Pattern
          2. 6.4.5.6.2 Synchronization Pattern
          3. 6.4.5.6.3 User-Defined Test Pattern
      6. 6.4.6 Power-Down Modes
      7. 6.4.7 Calibration Modes and Trimming
        1. 6.4.7.1 Foreground Calibration Mode
      8. 6.4.8 Offset Calibration
      9. 6.4.9 Trimming
    5. 6.5 Programming
      1. 6.5.1 Using the Serial Interface
        1. 6.5.1.1 SCS
        2. 6.5.1.2 SCLK
        3. 6.5.1.3 SDI
        4. 6.5.1.4 SDO
        5. 6.5.1.5 80
        6. 6.5.1.6 Streaming Mode
        7. 6.5.1.7 82
  8. Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 Reconfigurable Dual-Channel 2.5GSPS or Single-Channel 5GSPS Oscilloscope
        1. 7.2.1.1 Design Requirements
          1. 7.2.1.1.1 Input Signal Path
          2. 7.2.1.1.2 Clocking
          3. 7.2.1.1.3 ADC12DLx500
        2. 7.2.1.2 Application Curves
    3. 7.3 Initialization Set Up
    4. 7.4 Power Supply Recommendations
      1. 7.4.1 Power Sequencing
    5. 7.5 Layout
      1. 7.5.1 Layout Guidelines
      2. 7.5.2 Layout Example
  9. Register Maps
    1. 8.1 SPI_REGISTER_MAP Registers
  10. Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
    2. 9.2 接收文档更新通知
    3. 9.3 支持资源
    4. 9.4 Trademarks
    5. 9.5 静电放电警告
    6. 9.6 术语表
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics: AC Specifications (Single-Channel Mode)

Typical values at TA = +25°C, nominal supply voltages, default full-scale voltage (FS_RANGE_A = FS_RANGE_B = 0xA000), fIN = 347 MHz, AIN = –1 dBFS, fCLK = maximum rated clock frequency, filtered 1-VPP-DIFF sine-wave clock, DES_EN = 1, LDEMUX = 1, LALIGNED = 0, ADC_DITH = 0x01, LVDS driver high-swing mode (HSM), foreground calibration; minimum and maximum values are at nominal supply voltages and over operating free-air temperature range provided in the Recommended Operating Conditions table.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
ADC12DL500
FPBW Full-power input bandwidth (–3 dB)(1) Foreground calibration 7.5 GHz
CER Code error rate Maximum CER 10–18 errors/ sample
NSD Noise spectral density, no input signal, excludes fixed interleaving spurs (FS/2 and FS/4 spurs) Maximum full-scale voltage (FS_RANGE_A = 0xFFFF) setting -146.2 dBFS/Hz
Default full-scale voltage (FS_RANGE_A = 0xA000) setting -144.4
NF Noise figure Maximum full-scale voltage (FS_RANGE_A = 0xFFFF) setting, no input, ZS = 100 Ω 28.8 dB
Default full-scale voltage (FS_RANGE_A = 0xA000) setting, no input, ZS = 100 Ω 28.6
NOISEDC DC input noise standard deviation No input, excludes DC offset, includes fixed interleaving spurs (FS/2 and FS/4 spurs) 2.0 LSB
SNR Signal-to-noise ratio, large signal, excluding DC, HD2 to HD9 and interleaving spurs fIN = 97 MHz, AIN = –1 dBFS 56.7 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 57.6
fIN = 347 MHz, AIN = –1 dBFS 56.7
fIN = 797 MHz, AIN = –1 dBFS 56.5
SNR Signal-to-noise ratio, small signal, excluding DC, HD2 to HD9 and interleaving spurs fIN = 97 MHz, AIN = –16 dBFS 57.5 dBFS
fIN = 347 MHz, AIN = –16 dBFS 57.5
fIN = 797 MHz, AIN = –16 dBFS 57.4
SINAD Signal-to-noise and distortion ratio, large signal, excluding DC and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 55.2 dBFS
fIN = 347 MHz, AIN = –1 dBFS 55.1
fIN = 797 MHz, AIN = –1 dBFS 53.9
ENOB Effective number of bits, large signal, excluding DC and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 8.9 bits
fIN = 347 MHz, AIN = –1 dBFS 8.9
fIN = 797 MHz, AIN = –1 dBFS 8.7
SFDR Spurious-free dynamic range, large signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 61 dBFS
Spurious-free dynamic range, large signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 63
Spurious-free dynamic range, large signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 347 MHz, AIN = –1 dBFS 62
Spurious-free dynamic range, large signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 797 MHz, AIN = –1 dBFS 59
SFDR Spurious-free dynamic range, small signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 97 MHz, AIN = –16 dBFS 74 dBFS
fIN = 347 MHz, AIN = –16 dBFS 76
fIN = 797 MHz, AIN = –16 dBFS 73
FS/2 FS/2 fixed interleaving spur, independent of input signal No input -65 dBFS
FS/4 FS/4 fixed interleaving spur, independent of input signal No input -63 dBFS
HD2 2nd-order harmonic fIN = 97 MHz, AIN = –1 dBFS -71 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -73
fIN = 347 MHz, AIN = –1 dBFS -77
fIN = 797 MHz, AIN = –1 dBFS -67
HD3 3rd-order harmonic fIN = 97 MHz, AIN = –1 dBFS -72 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -68
fIN = 347 MHz, AIN = –1 dBFS -70
fIN = 797 MHz, AIN = –1 dBFS -66
FS/2-FIN FS/2-FIN interleaving spur, signal dependent fIN = 97 MHz, AIN = –1 dBFS -66 dBFS
fIN = 347 MHz, AIN = –1 dBFS -63
fIN = 797 MHz, AIN = –1 dBFS -61
FS/4±FIN FS/4±FIN interleaving spurs, signal dependent fIN = 97 MHz, AIN = –1 dBFS -72 dBFS
fIN = 347 MHz, AIN = –1 dBFS -74
fIN = 797 MHz, AIN = –1 dBFS -70
SPUR Worst harmonic 4th-order or higher fIN = 97 MHz, AIN = –1 dBFS -72 dBFS
fIN = 347 MHz, AIN = –1 dBFS -73
fIN = 797 MHz, AIN = –1 dBFS -72
IMD3 3rd-order intermodulation fIN = 97 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-85 dBFS
fIN = 347 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-79
fIN = 797 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-79
ADC12DL1500
FPBW Full-power input bandwidth (–3 dB)(1) Foreground calibration 7.5 GHz
CER Code error rate Maximum CER 10–18 errors/ sample
NSD Noise spectral density, no input signal, excludes fixed interleaving spurs (FS/2 and FS/4 spurs) Maximum full-scale voltage (FS_RANGE_A = 0xFFFF) setting -150.3 dBFS/Hz
Default full-scale voltage (FS_RANGE_A = 0xA000) setting -149.4
NF Noise figure Maximum full-scale voltage (FS_RANGE_A = 0xFFFF) setting, no input, ZS = 100 Ω 24.7 dB
Default full-scale voltage (FS_RANGE_A = 0xA000) setting, no input, ZS = 100 Ω 23.6
NOISEDC DC input noise standard deviation No input, excludes DC offset, includes fixed interleaving spurs (FS/2 and FS/4 spurs) 2.0 LSB
SNR Signal-to-noise ratio, large signal, excluding DC, HD2 to HD9 and interleaving spurs fIN = 97 MHz, AIN = –1 dBFS 56.6 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 57.3
fIN = 347 MHz, AIN = –1 dBFS 56.7
fIN = 797 MHz, AIN = –1 dBFS 56.5
fIN = 2397 MHz, AIN = –1 dBFS 55.7
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 56.2
SNR Signal-to-noise ratio, small signal, excluding DC, HD2 to HD9 and interleaving spurs fIN = 97 MHz, AIN = –16 dBFS 57.2 dBFS
fIN = 347 MHz, AIN = –16 dBFS 57.2
fIN = 797 MHz, AIN = –16 dBFS 57.2
fIN = 2397 MHz, AIN = –16 dBFS 57.1
SINAD Signal-to-noise and distortion ratio, large signal, excluding DC and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 55.8 dBFS
fIN = 347 MHz, AIN = –1 dBFS 55.8
fIN = 797 MHz, AIN = –1 dBFS 55.4
fIN = 2397 MHz, AIN = –1 dBFS 53.9
ENOB Effective number of bits, large signal, excluding DC and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 9.0 bits
fIN = 347 MHz, AIN = –1 dBFS 9.0
fIN = 797 MHz, AIN = –1 dBFS 8.9
fIN = 2397 MHz, AIN = –1 dBFS 8.7
SFDR Spurious-free dynamic range, large signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 67 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 64
fIN = 347 MHz, AIN = –1 dBFS 63
fIN = 797 MHz, AIN = –1 dBFS 63
fIN = 2397 MHz, AIN = –1 dBFS 58
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 54
SFDR Spurious-free dynamic range, small signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 97 MHz, AIN = –16 dBFS 75 dBFS
fIN = 347 MHz, AIN = –16 dBFS 72
fIN = 797 MHz, AIN = –16 dBFS 73
fIN = 2397 MHz, AIN = –16 dBFS 73
FS/2 FS/2 fixed interleaving spur, independent of input signal No input -65 dBFS
FS/4 FS/4 fixed interleaving spur, independent of input signal No input -69 dBFS
HD2 2nd-order harmonic fIN = 97 MHz, AIN = –1 dBFS -71 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -71
fIN = 347 MHz, AIN = –1 dBFS -73
fIN = 797 MHz, AIN = –1 dBFS -66
fIN = 2397 MHz, AIN = –1 dBFS -61
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -61
HD3 3rd-order harmonic fIN = 97 MHz, AIN = –1 dBFS -68 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -64
fIN = 347 MHz, AIN = –1 dBFS -72
fIN = 797 MHz, AIN = –1 dBFS -70
fIN = 2397 MHz, AIN = –1 dBFS -58
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -54
FS/2-FIN FS/2-FIN interleaving spur, signal dependent fIN = 97 MHz, AIN = –1 dBFS -71 dBFS
fIN = 347 MHz, AIN = –1 dBFS -65
fIN = 797 MHz, AIN = –1 dBFS -64
fIN = 2397 MHz, AIN = –1 dBFS -63
FS/4±FIN FS/4±FIN interleaving spurs, signal dependent fIN = 97 MHz, AIN = –1 dBFS -74 dBFS
fIN = 347 MHz, AIN = –1 dBFS -74
fIN = 797 MHz, AIN = –1 dBFS -70
fIN = 2397 MHz, AIN = –1 dBFS -74
SPUR Worst harmonic 4th-order or higher fIN = 97 MHz, AIN = –1 dBFS -69 dBFS
fIN = 347 MHz, AIN = –1 dBFS -73
fIN = 797 MHz, AIN = –1 dBFS -72
fIN = 2397 MHz, AIN = –1 dBFS -73
IMD3 3rd-order intermodulation fIN = 97 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-85 dBFS
fIN = 347 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-84
fIN = 797 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-83
fIN = 2397 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-70
ADC12DL2500
FPBW Full-power input bandwidth (–3 dB)(1) Foreground calibration 7.5 GHz
CER Code error rate Maximum CER 10–18 errors/ sample
NSD Noise spectral density, no input signal, excludes fixed interleaving spurs (FS/2 and FS/4 spurs) Maximum full-scale voltage (FS_RANGE_A = 0xFFFF) setting -152.2 dBFS/Hz
Default full-scale voltage (FS_RANGE_A = 0xA000) setting -151.3
NF Noise figure Maximum full-scale voltage (FS_RANGE_A = 0xFFFF) setting, no input, ZS = 100 Ω 22.8 dB
Default full-scale voltage (FS_RANGE_A = 0xA000) setting, no input, ZS = 100 Ω 21.7
NOISEDC DC input noise standard deviation No input, excludes DC offset, includes fixed interleaving spurs (FS/2 and FS/4 spurs) 2.0 LSB
SNR Signal-to-noise ratio, large signal, excluding DC, HD2 to HD9 and interleaving spurs fIN = 97 MHz, AIN = –1 dBFS 56.1 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 57.1
fIN = 347 MHz, AIN = –1 dBFS 56.2
fIN = 797 MHz, AIN = –1 dBFS 56.1
fIN = 2397 MHz, AIN = –1 dBFS 55.2
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 55.6
fIN = 4997 MHz, AIN = –1 dBFS 52.2
SNR Signal-to-noise ratio, small signal, excluding DC, HD2 to HD9 and interleaving spurs fIN = 97 MHz, AIN = –16 dBFS 56.7 dBFS
fIN = 347 MHz, AIN = –16 dBFS 56.8
fIN = 797 MHz, AIN = –16 dBFS 56.8
fIN = 2397 MHz, AIN = –16 dBFS 56.6
fIN = 4997 MHz, AIN = –16 dBFS 56.3
SINAD Signal-to-noise and distortion ratio, large signal, excluding DC and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 55.4 dBFS
fIN = 347 MHz, AIN = –1 dBFS 55.5
fIN = 797 MHz, AIN = –1 dBFS 53.9
fIN = 2397 MHz, AIN = –1 dBFS 52.9
fIN = 4997 MHz, AIN = –1 dBFS 48.29
ENOB Effective number of bits, large signal, excluding DC and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 8.9 bits
fIN = 347 MHz, AIN = –1 dBFS 8.9
fIN = 797 MHz, AIN = –1 dBFS 8.7
fIN = 2397 MHz, AIN = –1 dBFS 8.5
fIN = 4997 MHz, AIN = –1 dBFS 7.7
SFDR Spurious-free dynamic range, large signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 97 MHz, AIN = –1 dBFS 65 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 63
fIN = 347 MHz, AIN = –1 dBFS 65
fIN = 797 MHz, AIN = –1 dBFS 60
fIN = 2397 MHz, AIN = –1 dBFS 55
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting 54
fIN = 4997 MHz, AIN = –1 dBFS 48
SFDR Spurious-free dynamic range, small signal, excluding DC, FS/4 and FS/2 fixed spurs fIN = 97 MHz, AIN = –16 dBFS 71 dBFS
fIN = 347 MHz, AIN = –16 dBFS 74
fIN = 797 MHz, AIN = –16 dBFS 72
fIN = 2397 MHz, AIN = –16 dBFS 68
fIN = 4997 MHz, AIN = –16 dBFS 64
FS/2 FS/2 fixed interleaving spur, independent of input signal No input -60 dBFS
FS/4 FS/4 fixed interleaving spur, independent of input signal No input -64 dBFS
HD2 2nd-order harmonic fIN = 97 MHz, AIN = –1 dBFS -74 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -74
fIN = 347 MHz, AIN = –1 dBFS -71
fIN = 797 MHz, AIN = –1 dBFS -68
fIN = 2397 MHz, AIN = –1 dBFS -60
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -60
fIN = 4997 MHz, AIN = –1 dBFS -61
HD3 3rd-order harmonic fIN = 97 MHz, AIN = –1 dBFS -67 dBFS
fIN = 97 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -63
fIN = 347 MHz, AIN = –1 dBFS -69
fIN = 797 MHz, AIN = –1 dBFS -68
fIN = 2397 MHz, AIN = –1 dBFS -64
fIN = 2397 MHz, AIN = –1 dBFS, maximum FS_RANGE_A setting -57
fIN = 4997 MHz, AIN = –1 dBFS -54
FS/2-FIN FS/2-FIN interleaving spur, signal dependent fIN = 97 MHz, AIN = –1 dBFS -69 dBFS
fIN = 347 MHz, AIN = –1 dBFS -66
fIN = 797 MHz, AIN = –1 dBFS -62
fIN = 2397 MHz, AIN = –1 dBFS -58
fIN = 4997 MHz, AIN = –1 dBFS -54
FS/4±FIN FS/4±FIN interleaving spurs, signal dependent fIN = 97 MHz, AIN = –1 dBFS -74 dBFS
fIN = 347 MHz, AIN = –1 dBFS -69
fIN = 797 MHz, AIN = –1 dBFS -69
fIN = 2397 MHz, AIN = –1 dBFS -65
fIN = 4997 MHz, AIN = –1 dBFS -63
SPUR Worst harmonic 4th-order or higher fIN = 97 MHz, AIN = –1 dBFS -71 dBFS
fIN = 347 MHz, AIN = –1 dBFS -72
fIN = 797 MHz, AIN = –1 dBFS -72
fIN = 2397 MHz, AIN = –1 dBFS -71
fIN = 4997 MHz, AIN = –1 dBFS -66
IMD3 3rd-order intermodulation fIN = 97 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-79 dBFS
fIN = 347 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-82
fIN = 797 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-84
fIN = 2397 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-68
fIN = 4997 MHz ± 5 MHz,
AIN = –7 dBFS per tone
-57
Full-power input bandwidth (FPBW) is defined as the input frequency where the reconstructed output of the ADC has dropped 3 dB below the power of a full-scale input signal at a low input frequency. Useable bandwidth may exceed the –3-dB full-power input bandwidth.