ZHCSJ52A December   2019  – August 2021 LP875701-Q1

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Serial Bus Timing Requirements
    7. 6.7 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Descriptions
      1. 7.3.1 Multi-Phase DC/DC Converters
        1. 7.3.1.1 Overview
        2. 7.3.1.2 Multiphase Switcher Configurations
        3. 7.3.1.3 Buck Converter Load-Current Measurement
        4. 7.3.1.4 Spread-Spectrum Mode
      2. 7.3.2 Sync Clock Functionality
      3. 7.3.3 Power-Up
      4. 7.3.4 Regulator Control
        1. 7.3.4.1 Enabling and Disabling Regulators
      5. 7.3.5 Enable and Disable Sequences
      6. 7.3.6 Device Reset Scenarios
      7. 7.3.7 Diagnosis and Protection Features
        1. 7.3.7.1 Power-Good Information (PGOOD pin)
        2. 7.3.7.2 Warnings for Diagnosis (Interrupt)
          1. 7.3.7.2.1 Output Power Limit
          2. 7.3.7.2.2 Thermal Warning
        3. 7.3.7.3 Protection (Regulator Disable)
          1. 7.3.7.3.1 Short-Circuit and Overload Protection
          2. 7.3.7.3.2 Overvoltage Protection
          3. 7.3.7.3.3 Thermal Shutdown
        4. 7.3.7.4 Fault (Power Down)
          1. 7.3.7.4.1 Undervoltage Lockout
      8. 7.3.8 GPIO Signal Operation
      9. 7.3.9 Digital Signal Filtering
    4. 7.4 Device Functional Modes
      1. 7.4.1 Modes of Operation
    5. 7.5 Programming
      1. 7.5.1 I2C-Compatible Interface
        1. 7.5.1.1 Data Validity
        2. 7.5.1.2 Start and Stop Conditions
        3. 7.5.1.3 Transferring Data
        4. 7.5.1.4 I2C-Compatible Chip Address
        5. 7.5.1.5 Auto-Increment Feature
    6. 7.6 Register Maps
      1. 7.6.1 Register Descriptions
        1.       53
        2. 7.6.1.1  DEV_REV
        3. 7.6.1.2  OTP_REV
        4. 7.6.1.3  BUCK0_CTRL1
        5. 7.6.1.4  BUCK0_DELAY
        6. 7.6.1.5  GPIO2_DELAY
        7. 7.6.1.6  GPIO3_DELAY
        8. 7.6.1.7  RESET
        9. 7.6.1.8  CONFIG
        10. 7.6.1.9  INT_TOP1
        11. 7.6.1.10 INT_TOP2
        12. 7.6.1.11 INT_BUCK_0_1
        13. 7.6.1.12 INT_BUCK_2_3
        14. 7.6.1.13 TOP_STAT
        15. 7.6.1.14 BUCK_0_1_STAT
        16. 7.6.1.15 BUCK_2_3_STAT
        17. 7.6.1.16 TOP_MASK1
        18. 7.6.1.17 TOP_MASK2
        19. 7.6.1.18 BUCK_0_1_MASK
        20. 7.6.1.19 BUCK_2_3_MASK
        21. 7.6.1.20 SEL_I_LOAD
        22. 7.6.1.21 I_LOAD_2
        23. 7.6.1.22 I_LOAD_1
        24. 7.6.1.23 PGOOD_CTRL1
        25. 7.6.1.24 PGOOD_CTRL2
        26. 7.6.1.25 PGOOD_FLT
        27. 7.6.1.26 PLL_CTRL
        28. 7.6.1.27 PIN_FUNCTION
        29. 7.6.1.28 GPIO_CONFIG
        30. 7.6.1.29 GPIO_IN
        31. 7.6.1.30 GPIO_OUT
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 Inductor Selection
        2. 8.2.1.2 Input Capacitor Selection
        3. 8.2.1.3 Output Capacitor Selection
        4. 8.2.1.4 Snubber Components
        5. 8.2.1.5 Supply Filtering Components
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 接收文档更新通知
    2. 11.2 支持资源
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 术语表
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

I2C Serial Bus Timing Requirements

These specifications are ensured by design. VIN_Bx = 3.7 V, unless otherwise noted.
MINMAXUNIT
ƒSCLSerial clock frequencyStandard mode100kHz
Fast mode400
Fast mode+1MHz
High-speed mode, Cb = 100 pF3.4
High-speed mode, Cb = 400 pF1.7
tLOWSCL low timeStandard mode4.7µs
Fast mode1.3
Fast mode+0.5
High-speed mode, Cb = 100 pF160ns
High-speed mode, Cb = 400 pF320
tHIGHSCL high timeStandard mode4µs
Fast mode0.6
Fast mode+0.26
High-speed mode, Cb = 100 pF60ns
High-speed mode, Cb = 400 pF120
tSU;DATData setup timeStandard mode250ns
Fast mode100
Fast mode+50
High-speed mode10
tHD;DATData hold timeStandard mode103450ns
Fast mode10900
Fast mode+10
High-speed mode, Cb = 100 pF1070ns
High-speed mode, Cb = 400 pF10150
tSU;STASetup time for a start or a repeated start conditionStandard mode4.7µs
Fast mode0.6
Fast mode+0.26
High-speed mode160ns
tHD;STAHold time for a start or a repeated start conditionStandard mode4µs
Fast mode0.6
Fast mode+0.26
High-speed mode160ns
tBUFBus free time between a stop and start conditionStandard mode4.7µs
Fast mode1.3
Fast mode+0.5
tSU;STOSetup time for a stop conditionStandard mode4µs
Fast mode0.6
Fast mode+0.26
High-speed mode160ns
trDARise time of SDA signalStandard mode1000ns
Fast mode20300
Fast mode+120
High-speed mode, Cb = 100 pF1080
High-speed mode, Cb = 400 pF20160
tfDAFall time of SDA signalStandard mode300ns
Fast mode20 × (VDD / 5.5 V)300
Fast mode+20 × (VDD / 5.5 V)120
High-speed mode, Cb = 100 pF1080
High-speed mode, Cb = 400 pF30160
trCLRise time of SCL signalStandard mode1000ns
Fast mode20300
Fast mode+120
High-speed mode, Cb = 100 pF1040
High-speed mode, Cb = 400 pF2080
trCL1Rise time of SCL signal after a repeated start condition and after an acknowledge bitHigh-speed mode, Cb = 100 pF1080ns
High-speed mode, Cb = 400 pF20160
tfCLFall time of a SCL signalStandard mode300ns
Fast mode20 × (VDD / 5.5 V)300
Fast mode+20 × (VDD / 5.5 V)120
High-speed mode, Cb = 100 pF1040
High-speed mode, Cb = 400 pF2080
CbCapacitive load for each bus line (SCL and SDA)400pF
tSPPulse width of spike suppressed (SCL and SDA spikes that are less than the indicated width are suppressed)Standard mode, fast mode and fast mode+50ns
High-speed mode10
GUID-3470F4C6-0420-44DF-9BF8-41219F1EF105-low.gifFigure 6-1 I2C Timing