ZHCSFZ1A January   2017  – July 2018 DRV8886

UNLESS OTHERWISE NOTED, this document contains PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
    1.     简化原理图
  4. 修订历史记录
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Indexer Timing Requirements
    7. 6.7 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Stepper Motor Driver Current Ratings
        1. 7.3.1.1 Peak Current Rating
        2. 7.3.1.2 rms Current Rating
        3. 7.3.1.3 Full-Scale Current Rating
      2. 7.3.2  PWM Motor Drivers
      3. 7.3.3  Microstepping Indexer
      4. 7.3.4  Current Regulation
      5. 7.3.5  Controlling RREF With an MCU DAC
      6. 7.3.6  Decay Modes
        1. 7.3.6.1 Mode 1: Slow Decay for Increasing Current, Mixed Decay for Decreasing Current
        2. 7.3.6.2 Mode 2: Mixed Decay for Increasing and Decreasing Current
        3. 7.3.6.3 Mode 3: Slow Decay for Increasing and Decreasing Current
      7. 7.3.7  Blanking Time
      8. 7.3.8  Charge Pump
      9. 7.3.9  Linear Voltage Regulators
      10. 7.3.10 Logic and Multi-Level Pin Diagrams
      11. 7.3.11 Protection Circuits
        1. 7.3.11.1 VM Undervoltage Lockout (UVLO)
        2. 7.3.11.2 VCP Undervoltage Lockout (CPUV)
        3. 7.3.11.3 Overcurrent Protection (OCP)
        4. 7.3.11.4 Thermal Shutdown (TSD)
    4. 7.4 Device Functional Modes
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Stepper Motor Speed
        2. 8.2.2.2 Current Regulation
        3. 8.2.2.3 Decay Modes
      3. 8.2.3 Application Curves
  9. Power Supply Recommendations
    1. 9.1 Bulk Capacitance
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 文档支持
      1. 11.1.1 相关文档
    2. 11.2 接收文档更新通知
    3. 11.3 社区资源
    4. 11.4 商标
    5. 11.5 静电放电警告
    6. 11.6 术语表
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Pin Configuration and Functions

PWP PowerPAD™ Package
24-Pin HTSSOP
Top View
RHR Package
28-Pin WQFN With Exposed Thermal Pad
Top View

Pin Functions

PIN TYPE(1) DESCRIPTION
NAME NO.
HTSSOP WQFN
AOUT1 5 3 O Winding A output. Connect to stepper motor winding.
AOUT2 7 5
AVDD 13 12 PWR Internal regulator. Bypass to GND with a X5R or X7R, 0.47-μF, 6.3-V ceramic capacitor.
BOUT1 10 8 O Winding B output. Connect to stepper motor winding.
BOUT2 8 6
CPH 2 28 PWR Charge pump switching node. Connect a X5R or X7R, 0.022-μF, VM-rated ceramic capacitor from CPH to CPL.
CPL 1 27
DECAY 24 25 I Decay-mode setting. Sets the decay mode (see the Decay Modes section). Decay mode can be adjusted during operation.
DIR 20 21 I Direction input. Logic level sets the direction of stepping; internal pulldown resistor.
DVDD 14 13 PWR Internal regulator. Bypass to GND with a X5R or X7R, 0.47-μF, 6.3-V ceramic capacitor.
ENABLE 18 19 I Enable driver input. Logic high to enable device outputs; logic low to disable; internal pulldown resistor.
GND 12 10 PWR Device ground. Connect to system ground.
M0 21 22 I Microstepping mode-setting. Sets the step mode; tri-level pins; sets the step mode; internal pulldown resistor.
M1 22 23
NC 11 No connect. No internal connection
14
15
26
PGND 6 4 PWR Power ground. Connect to system ground.
9 7
RREF 16 17 I Current-limit analog input. Connect a resistor to ground to set full-scale regulation current.
STEP 19 20 I Step input. A rising edge causes the indexer to advance one step; internal pulldown resistor.
TRQ 23 24 I Current-scaling control. Scales the output current; tri-level pin.
VCP 3 1 PWR Charge pump output. Connect a X5R or X7R, 0.22-μF, 16-V ceramic capacitor to VM.
VM 4 2 PWR Power supply. Connect to motor supply voltage and bypass to GND with two 0.01-μF ceramic capacitors (one for each pin) plus a bulk capacitor rated for VM.
11 9
nFAULT 15 16 OD Fault indication. Pulled logic low with fault condition; open-drain output requires an external pullup resistor.
nSLEEP 17 18 I Sleep mode input. Logic high to enable device; logic low to enter low-power sleep mode; internal pulldown resistor.
I = input, O = output, PWR = power, OD = open-drain