ZHCSSJ4B December   2022  – April 2024 CC1354R10

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 功能方框图
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
    1. 6.1 Pin Diagram—RGZ Package (Top View)
    2. 6.2 Signal Descriptions—RGZ Package
    3. 6.3 Connections for Unused Pins and Modules—RGZ Package
    4. 6.4 Pin Diagram—RSK Package (Top View)
    5. 6.5 Signal Descriptions—RSK Package
    6. 6.6 Connection of Unused Pins and Module—RSK Package
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Power Supply and Modules
    5. 7.5  Power Consumption—Power Modes
    6. 7.6  Power Consumption—Radio Modes
    7. 7.7  Nonvolatile (Flash) Memory Characteristics
    8. 7.8  Thermal Resistance Characteristics
    9. 7.9  RF Frequency Bands
    10. 7.10 861MHz to 1054MHz—Receive (RX)
    11. 7.11 861MHz to 1054MHz—Transmit (TX) 
    12. 7.12 861MHz to 1054MHz - PLL Phase Noise Wideband Mode
    13. 7.13 861MHz to 1054MHz - PLL Phase Noise Narrowband Mode
    14. 7.14 Bluetooth Low Energy—Receive (RX)
    15. 7.15 Bluetooth Low Energy—Transmit (TX)
    16. 7.16 Zigbee and Thread - IEEE 802.15.4-2006 2.4GHz (OQPSK DSSS1:8, 250kbps) - RX
    17. 7.17 Zigbee and Thread - IEEE 802.15.4-2006 2.4GHz (OQPSK DSSS1:8, 250kbps) - TX
    18. 7.18 Timing and Switching Characteristics
      1. 7.18.1 Reset Timing
      2. 7.18.2 Wakeup Timing
      3. 7.18.3 Clock Specifications
        1. 7.18.3.1 48MHz Clock Input (TCXO)
        2. 7.18.3.2 48MHz Crystal Oscillator (XOSC_HF)
        3. 7.18.3.3 48MHz RC Oscillator (RCOSC_HF)
        4. 7.18.3.4 2MHz RC Oscillator (RCOSC_MF)
        5. 7.18.3.5 32.768 kHz Crystal Oscillator (XOSC_LF)
        6. 7.18.3.6 32 kHz RC Oscillator (RCOSC_LF)
      4. 7.18.4 Serial Peripheral Interface (SPI) Characteristics
        1. 7.18.4.1 SPI Characteristics
        2. 7.18.4.2 SPI Master Mode
        3. 7.18.4.3 SPI Master Mode Timing Diagrams
        4. 7.18.4.4 SPI Slave Mode
        5. 7.18.4.5 SPI Slave Mode Timing Diagrams
      5. 7.18.5 UART
        1. 7.18.5.1 UART Characteristics
    19. 7.19 Peripheral Characteristics
      1. 7.19.1 ADC
        1. 7.19.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 7.19.2 DAC
        1. 7.19.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 7.19.3 Temperature and Battery Monitor
        1. 7.19.3.1 Temperature Sensor
        2. 7.19.3.2 Battery Monitor
      4. 7.19.4 Comparators
        1. 7.19.4.1 Low-Power Clocked Comparator
        2. 7.19.4.2 Continuous Time Comparator
      5. 7.19.5 Current Source
        1. 7.19.5.1 Programmable Current Source
      6. 7.19.6 GPIO
        1. 7.19.6.1 GPIO DC Characteristics
    20. 7.20 Typical Characteristics
      1. 7.20.1 MCU Current
      2. 7.20.2 RX Current
      3. 7.20.3 TX Current
      4. 7.20.4 RX Performance
      5. 7.20.5 TX Performance
      6. 7.20.6 ADC Performance
  9. 8 Detailed Description
    1. 8.1  Overview
    2. 8.2  System CPU
    3. 8.3  Radio (RF Core)
      1. 8.3.1 Proprietary Radio Formats
      2. 8.3.2 Bluetooth 5.3 Low Energy
      3. 8.3.3 802.15.4 Thread, Zigbee, and 6LoWPAN
    4. 8.4  Memory
    5. 8.5  Sensor Controller
    6. 8.6  Cryptography
    7. 8.7  Timers
    8. 8.8  Serial Peripherals and I/O
    9. 8.9  Battery and Temperature Monitor
    10. 8.10 µDMA
    11. 8.11 Debug
    12. 8.12 Power Management
    13. 8.13 Clock Systems
    14. 8.14 Network Processor
  10. 9 Application, Implementation, and Layout
    1. 9.1 Reference Designs
    2. 9.2 Junction Temperature Calculation
  11. 10Device and Documentation Support
    1. 10.1 Tools and Software
      1. 10.1.1 SimpleLink™ Microcontroller Platform
    2. 10.2 Documentation Support
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 静电放电警告
    6. 10.6 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Packaging Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.14 Bluetooth Low Energy—Receive (RX)

When measured on the LP-EM-CC1354P10-1 reference design with Tc = 25°C, VDDS = 3.0V, fRF= 2440MHz with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX path. All measurements are performed conducted.
 
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
125kbps (LE Coded)
Receiver sensitivity Differential mode. BER = 10–3 –105 dBm
Receiver saturation Differential mode. BER = 10–3 >5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–300 / 300) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–320 / 240) ppm
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (255-byte packets) > (–100 / 125) ppm
Co-channel rejection(1) Wanted signal at –79dBm, modulated interferer in channel, BER = 10–3 –1.5 dB
Selectivity, ±1MHz(1) Wanted signal at –79dBm, modulated interferer at ±1MHz, BER = 10–3 8 / 4.5(2) dB
Selectivity, ±2MHz(1) Wanted signal at –79dBm, modulated interferer at ±2MHz, BER = 10–3  44 / 39(2) dB
Selectivity, ±3MHz(1) Wanted signal at –79dBm, modulated interferer at ±3MHz, BER = 10–3 43 / 43(2) dB
Selectivity, ±4MHz(1) Wanted signal at –79dBm, modulated interferer at ±4MHz, BER = 10–3 44 / 43(2) dB
Selectivity, ±6MHz(1) Wanted signal at –79dBm, modulated interferer at ≥ ±6MHz, BER = 10–3 48 / 43(2) dB
Selectivity, ±7MHz Wanted signal at –79dBm, modulated interferer at ≥ ±7MHz, BER = 10–3 51 / 45(2) dB
Selectivity, Image frequency(1) Wanted signal at –79dBm, modulated interferer at image frequency, BER = 10–3 39 dB
Selectivity, Image frequency ±1MHz(1) Note that Image frequency + 1MHz is the Co- channel –1MHz. Wanted signal at –79dBm, modulated interferer at ±1MHz from image frequency, BER = 10–3 4.5 / 44 (2) dB
RSSI Range 89 dB
RSSI Accuracy (+/-) ±4 dB
500kbps (LE Coded)
Receiver sensitivity Differential mode. BER = 10–3 –100 dBm
Receiver saturation Differential mode. BER = 10–3 > 5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–300 / 300) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–450 / 450) ppm
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (255-byte packets) > (–175 / 175) ppm
Co-channel rejection(1) Wanted signal at –72dBm, modulated interferer in channel, BER = 10–3 –3.5 dB
Selectivity, ±1MHz(1) Wanted signal at –72dBm, modulated interferer at ±1MHz, BER = 10–3 8 / 4(2) dB
Selectivity, ±2MHz(1) Wanted signal at –72dBm, modulated interferer at ±2MHz, BER = 10–3 41 / 37(2) dB
Selectivity, ±3MHz(1) Wanted signal at –72dBm, modulated interferer at ±3MHz, BER = 10–3 44 / 41(2) dB
Selectivity, ±4MHz(1) Wanted signal at –72dBm, modulated interferer at ±4MHz, BER = 10–3 44 / 43(2) dB
Selectivity, ±6MHz(1) Wanted signal at –72dBm, modulated interferer at ≥ ±6MHz, BER = 10–3 46 / 43(2) dB
Selectivity, ±7MHz Wanted signal at –72dBm, modulated interferer at ≥ ±7MHz, BER = 10–3 49 / 45(2) dB
Selectivity, Image frequency(1) Wanted signal at –72dBm, modulated interferer at image frequency, BER = 10–3 37 dB
Selectivity, Image frequency ±1MHz(1) Note that Image frequency + 1MHz is the Co- channel –1MHz. Wanted signal at –72dBm, modulated interferer at ±1MHz from image frequency, BER = 10–3 4 / 46(2) dB
RSSI Range 85 dB
RSSI Accuracy (+/-) ±4 dB
1 Mbps (LE 1M)
Receiver sensitivity Differential mode. BER = 10–3 –97 dBm
Receiver saturation Differential mode. BER = 10–3  > 5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–350 / 350) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–750 / 750) ppm
Co-channel rejection(1) Wanted signal at –67dBm, modulated interferer in channel, BER = 10–3 –6 dB
Selectivity, ±1MHz(1) Wanted signal at –67dBm, modulated interferer at ±1MHz, BER = 10–3 7 / 4(2) dB
Selectivity, ±2MHz(1) Wanted signal at –67dBm, modulated interferer at ±2MHz,BER = 10–3 40 / 33(2) dB
Selectivity, ±3MHz(1) Wanted signal at –67dBm, modulated interferer at ±3MHz, BER = 10–3 36 / 41(2) dB
Selectivity, ±4MHz(1) Wanted signal at –67dBm, modulated interferer at ±4MHz, BER = 10–3 36 / 45(2) dB
Selectivity, ±5MHz or more(1) Wanted signal at –67dBm, modulated interferer at ≥ ±5MHz, BER = 10–3 40 dB
Selectivity, image frequency(1) Wanted signal at –67dBm, modulated interferer at image frequency, BER = 10–3 33 dB
Selectivity, image frequency
±1MHz(1)		 Note that Image frequency + 1MHz is the Co- channel –1MHz. Wanted signal at –67dBm, modulated interferer at ±1MHz from image frequency, BER = 10–3 4 / 41(2) dB
Out-of-band blocking(3) 30MHz to 2000MHz –10 dBm
Out-of-band blocking 2003MHz to 2399MHz –18 dBm
Out-of-band blocking 2484MHz to 2997MHz –12 dBm
Out-of-band blocking 3000MHz to 12.75GHz –2 dBm
Intermodulation Wanted signal at 2402MHz, –64dBm. Two interferers at 2405 and 2408MHz respectively, at the given power level  –42 dBm
Spurious emissions,
30 to 1000MHz(4)		 Measurement in a 50 Ω single-ended load. < –59 dBm
Spurious emissions,
1 to 12.75GHz(4)		 Measurement in a 50 Ω single-ended load. < –47 dBm
RSSI dynamic range 70 dB
RSSI accuracy ±4 dB
2 Mbps (LE 2M)
Receiver sensitivity Differential mode. Measured at SMA connector, BER = 10–3  –92 dBm
Receiver saturation Differential mode. Measured at SMA connector, BER = 10–3 > 5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–500 / 500) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–700 / 750) ppm
Co-channel rejection(1) Wanted signal at –67dBm, modulated interferer in channel,BER = 10–3 –7 dB
Selectivity, ±2MHz(1) Wanted signal at –67dBm, modulated interferer at ±2MHz, Image frequency is at –2MHz, BER = 10–3 8 / 4(2) dB
Selectivity, ±4MHz(1) Wanted signal at –67dBm, modulated interferer at ±4MHz, BER = 10–3 35 / 32(2) dB
Selectivity, ±6MHz(1) Wanted signal at –67dBm, modulated interferer at ±6MHz, BER = 10–3 37 / 34(2) dB
Selectivity, image frequency(1) Wanted signal at –67dBm, modulated interferer at image frequency, BER = 10–3 4 dB
Selectivity, image frequency
±2MHz(1)		 Note that Image frequency + 2MHz is the Co-channel. Wanted signal at –67dBm, modulated interferer at ±2MHz from image frequency, BER = 10–3 –7 / 36(2) dB
Out-of-band blocking(3) 30MHz to 2000MHz –16 dBm
Out-of-band blocking 2003MHz to 2399MHz –21 dBm
Out-of-band blocking 2484MHz to 2997MHz –15 dBm
Out-of-band blocking 3000MHz to 12.75GHz –20 dBm
Intermodulation Wanted signal at 2402MHz, –64dBm. Two interferers at 2408 and 2414MHz respectively, at the given power level –37 dBm
RSSI Range 64 dB
RSSI Accuracy (+/-) ±4 dB
(1) Numbers given as I/C dB.
(2) X / Y, where X is +N MHz and Y is –N MHz.
(3) Excluding one exception at Fwanted / 2, per Bluetooth Specification.
(4) Suitable for systems targeting compliance with worldwide radio-frequency regulations ETSI EN 300 328 and EN 300 440 Class 2 (Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan).