BQ28Z620-DEVICE-FW
BQ28Z620 family of gauges firmware
BQ28Z620-DEVICE-FW
개요
The Texas Instruments BQ28Z620 device is a highly integrated, accurate, 1-series to 2-series cell gas gauge and protection solution, enabling autonomous charger control and cell balancing.
The BQ28Z620-DEVICE-FW enables autonomous charge control through Master Mode I²C broadcasts of charging current and voltage information, eliminating software overhead that is typically incurred by the system’s host controller.
The BQ28Z620-DEVICE-FW device provides a fully integrated pack-based solution with a flash programmable custom reduced instruction-set CPU (RISC), safety protection, and authentication for 1- to 2-series cell Li-ion and Li-polymer battery packs.
The BQ28Z620-DEVICE-FW communicates via an I²C compatible interface and combines an ultra-low-power, high-speed TI BQBMP processor, high-accuracy analog measurement capabilities, integrated flash memory, an array of peripheral and communication ports, an N-CH FET drive, and a SHA-1 Authentication transform responder into a complete, high-performance battery management solution.
특징
- Autonomous battery charging control, using a dedicated MASTER mode I²C interface
- 400-kHz I²C bus communications interface, including a 1.2-V logic level for high-speed programming and data access
- Cell balancing with an internal bypass to optimize battery health
- A high-side protection N-CH FET drive enables serial bus communication during fault conditions
- Programmable protection levels for voltage, current, and temperature
- Support for simultaneous current and voltage sampling
- Supports down to 0.5-mΩ current sense resistor while capable of 1-mA current measurement
- SHA-1 authentication responder for increased battery pack security
다운로드
BQ28Z620-DEVICE-FW — Firmware for BQ28Z620 family of gauges
지원되는 제품 및 하드웨어
제품
배터리 연료 게이지
하드웨어 개발
평가 보드
BQ28Z620-DEVICE-FW — Firmware for BQ28Z620 family of gauges
BQ28Z620-R1 v1.01 firmware installer
제품
배터리 연료 게이지
하드웨어 개발
평가 보드
출시 정보
The Texas Instruments BQ28Z620 device is a highly integrated, accurate, 1-series to 2-series cell gas gauge and protection solution, enabling autonomous charger control and cell balancing.
The BQ28Z620-DEVICE-FW enables autonomous charge control through Master Mode I2C broadcasts of charging current and voltage information, eliminating software overhead that is typically incurred by the system’s host controller.
The BQ28Z620-DEVICE-FW device provides a fully integrated pack-based solution with a flash programmable custom reduced instruction-set CPU (RISC), safety protection, and authentication for 1- to 2-series cell Li-ion and Li-polymer battery packs.
The BQ28Z620-DEVICE-FW communicates via an I2C compatible interface and combines an ultra-low-power, high-speed TI BQBMP processor, high-accuracy analog measurement capabilities, integrated flash memory, an array of peripheral and communication ports, an N-CH FET drive, and a SHA-1 Authentication transform responder into a complete, high-performance battery management solution.
Features
- Autonomous battery charging control, using a dedicated MASTER mode I2C interface
- 400-kHz I2C bus communications interface, including a 1.2-V logic level for high-speed programming and data access
- Cell balancing with an internal bypass to optimize battery health
- A high-side protection N-CH FET drive enables serial bus communication during fault conditions
- Programmable protection levels for voltage, current, and temperature
- Support for simultaneous current and voltage sampling
- Supports down to 0.5-mΩ current sense resistor while capable of 1-mA current measurement
- SHA-1 authentication responder for increased battery pack security
필요할 수 있는 추가 리소스
BQ-BMS-PROGRAMMER-SW — Command line programmers for BQ products
지원되는 제품 및 하드웨어
제품
배터리 연료 게이지
하드웨어 개발
레퍼런스 디자인
평가 보드
BQ-BMS-PROGRAMMER-SW — Command line programmers for BQ products
SDK, API, and Programmer installer
제품
배터리 연료 게이지
하드웨어 개발
레퍼런스 디자인
평가 보드
문서
Quick Tips text document for Command line programmers
Software Manifest
출시 정보
Description:
BQ-BATTERY-PROGRAMMER-SW software development kit (SDK) is a collection of robust software command line tools that assist with the process of programming, testing, or assembling packs that use TI Battery management products. The executables in this software work with the MKST-3P-ALT-EV2300 MKS Technology alternative for EV2300 communications transceiver. The executables work with a single station but can be extended to multiple stations by using additional software and GUI from MKS Technology Inc. . Support for multiple stations is not included in this software.
There are multiple executables in the download, usually one per family of products. Older products such as BQ20xxx and BQ30xxx are also supported. Examples using the C++ programming language API and Python® programming language are provided for custom development.
Requirements:
- Hardware: MKST-3P-ALT-EV2300
- Supported operating systems: Windows (32 and 64 bits)
- Software: Microsoft Visual Studio 2010 C++ Runtime redistributable
Features:
- Collection of command line executables for Windows
- Small executable size with few dependencies
- Fast programming
- Supports BQFS/DFFS and SREC file formats
- Provides C API for custom code development
- Callable from other programs for automation
- Portable design simplifies deployment
- Separately downloadable support software to enable legacy software like BQEVSW and ADVANCED-BQMTESTER to work with MKST-3P-ALT-EV2300
Getting started:
1. Download the software
2. Run the installer
3. The executables, C API and Python API files can be found in the install location
4. Run the command line executable without arguments to get usage help. Refer to Readme.txt in the install folder for more information and how to get help using the command line.
새 소식
- Added support for BQ78350 and BQ34Z100