BQ35100
- Fuel gauge and battery diagnostics for flow meter
applications predict end-of-service or early battery failure
- Supports lithium thionyl chloride (Li-SOCl2) and lithium manganese dioxide (Li-MnO2) chemistry batteries
- Accurate voltage, temperature, current, and coulomb counter measurements that report battery health and service life
- State-of-health (SOH) algorithm for Li-MnO2
- End-of-service (EOS algorithm for Li-SOCl2)
- Coulomb accumulation (ACC) algorithm for all battery types
- Ultra-low average power consumption to maximize battery
run time
- Gauge enabled through host-controlled periodic updates
- State-of-health (SOH) ~0.06 µA
- End-of-service (EOS) ~0.35 µA
- Coulomb accumulation (ACC) diagnostic updates ~0.3 µA
- System interaction
capabilities
- I2C host communication, providing battery parameter and status access
- Configurable host interrupt
- Battery information data logging options for in operation diagnostics and failure analysis
- SHA-1 authentication to help prevent counterfeit battery use
The BQ35100 Battery Fuel Gauge and End-Of-Service Monitor provides highly configurable fuel gauging for non-rechargeable (primary) lithium batteries without requiring a forced discharge of the battery. Built so that optimization is not necessary to achieve accurate gauging, the BQ35100 device uses patented TI gauging algorithms to support the option to seamlessly replace an old battery with a new one.
The BQ35100 device provides accurate results with ultra-low average power consumption where less than 2 µA can be achieved through host control via the GAUGE ENABLE (GE) pin. The device is only required to be powered long enough, at a system-determined update frequency, to gather data and to make calculations to support the selected algorithm. A typical system may need to only be updated once every 8 hours as the gauge is not required to be powered to measure all discharge activity.
The fuel gauging functions use voltage, current, and temperature measurements to provide state-of-health (SOH) data and end-of-service (EOS) warning information where the host can read the gathered data through a 400-kHz I2C bus. An ALERT output, based on a variety of configurable status and data options, is also available to interrupt the host.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | BQ35100 Lithium Primary Battery Fuel Gauge and End-Of-Service Monitor datasheet (Rev. E) | PDF | HTML | 2019. 4. 8 | |
| * | 사용 설명서 | bq35100 Technical Reference Manual (Rev. C) | PDF | HTML | 2018. 3. 26 | |
| 애플리케이션 노트 | How to Configure the BQ35100 for EOS Mode | PDF | HTML | 2022. 9. 15 | ||
| 애플리케이션 노트 | Alternative Gauging Techniques for Flow Meters and the Benefits of the bq35100 | 2018. 11. 15 | |||
| 기술 문서 | Facing smart meter design challenges, part 1: maximizing battery life | PDF | HTML | 2018. 8. 16 | ||
| Application brief | Using the BQ35100 with Li-Primary Based Applications | PDF | HTML | 2018. 6. 20 | ||
| 애플리케이션 노트 | Gauge Communication | 2017. 1. 12 | |||
| 애플리케이션 노트 | Using I2C Communications With the bq34110 bq35100 and bq34z100-G1 Series of Gas | PDF | HTML | 2016. 11. 9 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BQ35100EVM-795 — bq35100 서비스 종료 모니터 가스 게이지를 사용하는 리튬 1차 셀 평가 모듈
BQSTUDIO-STABLE — Battery Management Studio (bqStudio) Software – stable version downloads for bq series of TI battery fuel gauges
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
BQSTUDIO-TEST — Battery Management Studio (bqStudio) Software – untested version downloads
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
BQ-BMS-PROGRAMMER-SW — Command line programmers for BQ products
BQ-BATTERY-PROGRAMMER-SW 소프트웨어 개발 키트(SDK)는 TI 배터리 관리 제품을 사용하는 팩의 프로그래밍, 테스트 또는 조립 프로세스를 지원하는 강력한 소프트웨어 명령줄 툴 모음입니다. 이 소프트웨어의 실행 파일은 EV2300 통신 트랜스시버용 MKST-3P-ALT-EV2300 MKS 기술 대안과 함께 작동합니다. 실행 파일은 단일 스테이션에서 작동하지만 MKS Technology Inc.의 추가 소프트웨어 및 GUI를 사용하여 여러 스테이션으로 확장할 수 있습니다. 이 소프트웨어에는 여러 스테이션에 대한 (...)
SLUC623 — bq35100 Firmware
TIDA-01236 — 무선 초음파 가스 누출 감지기에서 코인 셀 배터리 작동 시간을 늘리기 위한 레퍼런스 설계
이 레퍼런스 설계는 특정 특징에 대한 초음파 스펙트럼을 분석하여 가스 누출을 감지하는 저전력 무선 센서를 보여줍니다. 이 시스템은 단일 리튬 1차 코인 셀로 작동하고 기지국과 무선으로 통신하도록 설계되어 배선에 대한 모든 요구 사항이 없고 설치가 간편합니다. 이 설계는 초저전력 배터리 연료 게이지를 통합하여 배터리 상태를 정확하게 예측하고 예정된 배터리 교체를 위해 향후 수명 종료에 대한 사전 알림을 제공합니다.
TIDA-01546 — 배터리로 구동되는 스마트 유량 계량기의 배터리 및 시스템 상태 모니터링 레퍼런스 설계
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| TSSOP (PW) | 14 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.