主页 电源管理 栅极驱动器 低侧驱动器
主页
电源管理
栅极驱动器
低侧驱动器

TPIC44H01

正在供货

具有故障模式选择的 1.2mA/1.2mA 4 通道栅极驱动器

立即订购
数据表

TPIC44H01

正在供货
立即订购

产品详情

Number of channels 4 Power switch MOSFET Peak output current (A) 0.004 Input supply voltage (min) (V) 8 Input supply voltage (max) (V) 24 Features Fault Diagnostics, OVP, SPI Interface, Sleep mode Operating temperature range (°C) -40 to 125 Rise time (ns) 5000 Fall time (ns) 5000 Propagation delay time (µs) 5 Input threshold CMOS Channel input logic Non-Inverting Input negative voltage (V) -0.3 Rating Automotive Driver configuration Quad inputs
Number of channels 4 Power switch MOSFET Peak output current (A) 0.004 Input supply voltage (min) (V) 8 Input supply voltage (max) (V) 24 Features Fault Diagnostics, OVP, SPI Interface, Sleep mode Operating temperature range (°C) -40 to 125 Rise time (ns) 5000 Fall time (ns) 5000 Propagation delay time (µs) 5 Input threshold CMOS Channel input logic Non-Inverting Input negative voltage (V) -0.3 Rating Automotive Driver configuration Quad inputs
TSSOP (DA) 32 89.1 mm² (11 mm × 8.1 mm)
  • Serial or Parallel Control of Gate Outputs
  • Sleep State for Low Quiescent Current
  • Independent On-State Source Short-to-Ground (Shorted-Load) Detection/Protection
  • Independent On-State Over-Current Detection/Protection With Dynamic Fault Threshold
  • Independent Off-State Open-Load Detection
  • Supply Over-Voltage Lockout Protection
  • Asynchronous Open-Drain Fault Interrupt Terminal to Flag Fault Conditions. Output Can be OR'ed With Multiple Devices
  • Encoded Fault Status Reporting Through Serial Output Terminal (2-Bits Per Channel)
  • Programmable On-State Fault Deglitch Timers
  • High Impedance CMOS Compatible Inputs With Hysteresis
  • Fault Mode Selection: Outputs Latched Off or Switched at Low Duty Cycle
  • Device Can be Cascaded With Serial Interface

TI is a trademark of Texas Instruments Incorporated.
  • Serial or Parallel Control of Gate Outputs
  • Sleep State for Low Quiescent Current
  • Independent On-State Source Short-to-Ground (Shorted-Load) Detection/Protection
  • Independent On-State Over-Current Detection/Protection With Dynamic Fault Threshold
  • Independent Off-State Open-Load Detection
  • Supply Over-Voltage Lockout Protection
  • Asynchronous Open-Drain Fault Interrupt Terminal to Flag Fault Conditions. Output Can be OR'ed With Multiple Devices
  • Encoded Fault Status Reporting Through Serial Output Terminal (2-Bits Per Channel)
  • Programmable On-State Fault Deglitch Timers
  • High Impedance CMOS Compatible Inputs With Hysteresis
  • Fault Mode Selection: Outputs Latched Off or Switched at Low Duty Cycle
  • Device Can be Cascaded With Serial Interface

TI is a trademark of Texas Instruments Incorporated.

The TPIC44H01 is a four channel high-side pre-FET driver which provides serial or parallel input interface to control four external NMOS power FETs. It is designed for use in low frequency switching applications for resistive or inductive loads, including solenoids and incandescent bulbs.

Each channel has over-current, short-to-ground, and open-load detection that is flagged through the FLT\ pin and distinguished through the serial interface. Over-current thresholds are set through the V(PK_x) and V(COMP1-4) pins. Short-to-ground and open-load thresholds are set internally to approximately 2.5 V. The AR_ENBL pin is used to define the operation of the device during a fault condition, allowing the outputs to either latch off or to enter a low duty cycle, auto-retry mode. An over-voltage lockout circuit on V(PWR) protects the device and the external FETs. A low current sleep state mode is provided to allow the TPIC44H01 to be used in applications where V(PWR) is connected directly to the battery. An internal charge pump allows the use of N-channel FETs for high-side drive applications, while current-limit gate drive provides slope control for reduced RFI.

By having the unique ability to develop a dynamic over-current threshold, the TPIC44H01 can be used to drive incandescent bulbs with long inrush currents without falsely flagging a fault. Likewise, the user can select an internally set over-current threshold of ~1.25 V by pulling the respective V(COMP1-4) pin to VCC.

The 8-bit serial peripheral interface (SPI) allows the user to command any of the four outputs on or off, to program one of eight possible open-load, over-current, and short-load fault deglitch timer settings, and to engage the sleep state. Data is clocked into the SDI pin on the rising edge of SCLK and clocked out of the SDO pin on the SCLK falling edge. The serial input bits are logic OR'ed with the IN1-IN4 parallel inputs pins. The serial interface is also used to read normal-load, open-load, over-current, and short-to-ground conditions for each channel. Over-voltage lockout can be detected when the FLT\ pin is low and no bits are set in the SDO register. Multiple TPIC44H01 devices may be cascaded together using the serial interface to further reduce I/O lines from the host controller.

The TPIC44H01 is a four channel high-side pre-FET driver which provides serial or parallel input interface to control four external NMOS power FETs. It is designed for use in low frequency switching applications for resistive or inductive loads, including solenoids and incandescent bulbs.

Each channel has over-current, short-to-ground, and open-load detection that is flagged through the FLT\ pin and distinguished through the serial interface. Over-current thresholds are set through the V(PK_x) and V(COMP1-4) pins. Short-to-ground and open-load thresholds are set internally to approximately 2.5 V. The AR_ENBL pin is used to define the operation of the device during a fault condition, allowing the outputs to either latch off or to enter a low duty cycle, auto-retry mode. An over-voltage lockout circuit on V(PWR) protects the device and the external FETs. A low current sleep state mode is provided to allow the TPIC44H01 to be used in applications where V(PWR) is connected directly to the battery. An internal charge pump allows the use of N-channel FETs for high-side drive applications, while current-limit gate drive provides slope control for reduced RFI.

By having the unique ability to develop a dynamic over-current threshold, the TPIC44H01 can be used to drive incandescent bulbs with long inrush currents without falsely flagging a fault. Likewise, the user can select an internally set over-current threshold of ~1.25 V by pulling the respective V(COMP1-4) pin to VCC.

The 8-bit serial peripheral interface (SPI) allows the user to command any of the four outputs on or off, to program one of eight possible open-load, over-current, and short-load fault deglitch timer settings, and to engage the sleep state. Data is clocked into the SDI pin on the rising edge of SCLK and clocked out of the SDO pin on the SCLK falling edge. The serial input bits are logic OR'ed with the IN1-IN4 parallel inputs pins. The serial interface is also used to read normal-load, open-load, over-current, and short-to-ground conditions for each channel. Over-voltage lockout can be detected when the FLT\ pin is low and no bits are set in the SDO register. Multiple TPIC44H01 devices may be cascaded together using the serial interface to further reduce I/O lines from the host controller.
filter 查找其他 低侧驱动器
下载

您可能感兴趣的相似产品

open-in-new 比较替代产品
功能与比较器件相似。
UCC57108 正在供货 具有 DESAT 保护和 8V UVLO 的单通道 30V VDD、3A/3A 低侧驱动器 More recent low-side device with DESAT protection, higher drive current and smaller package options

技术文档

未找到结果。请清除搜索并重试。
查看全部 1
顶层文档 类型 标题 格式选项 下载最新的英语版本 日期
* 数据表 4-Channel Serial And Parallel High-Side Pre-Driver 数据表 1998-5-15

订购和质量

支持和培训

可获得 TI 工程师技术支持的 TI E2E™ 论坛

查看全部论坛主题 查看英文版全部论坛主题

所有内容均由 TI 和社区贡献者按“原样”提供，并不构成 TI 规范。请参阅使用条款。

如果您对质量、包装或订购 TI 产品有疑问，请参阅 TI 支持。​​​​​​​​​​​​​​