产品详细信息

Regulated outputs (#) 2 Vin (Min) (V) 2.8 Vin (Max) (V) 5.5 Iout (Max) (A) 5 Rating Automotive Step-down DC/DC controller 0 Step-down DC/DC converter 2 Step-up DC/DC controller 0 Step-up DC/DC converter 0 LDO 0 Iq (Typ) (mA) 0.0067 Features Diagnostics, Dynamic Voltage Scaling, Enable, Enable Pin, I2C Control, Over Current Protection, Power Good, Power Sequencing, Power Supply and System Monitoring, Spread-Spectrum Clock (SSC) Generation, Thermal Shutdown, UVLO Fixed Operating temperature range (C) -40 to 125 Shutdown current (ISD) (Typ) (uA) 1.4 Configurability Factory programmable, Software configurable
Regulated outputs (#) 2 Vin (Min) (V) 2.8 Vin (Max) (V) 5.5 Iout (Max) (A) 5 Rating Automotive Step-down DC/DC controller 0 Step-down DC/DC converter 2 Step-up DC/DC controller 0 Step-up DC/DC converter 0 LDO 0 Iq (Typ) (mA) 0.0067 Features Diagnostics, Dynamic Voltage Scaling, Enable, Enable Pin, I2C Control, Over Current Protection, Power Good, Power Sequencing, Power Supply and System Monitoring, Spread-Spectrum Clock (SSC) Generation, Thermal Shutdown, UVLO Fixed Operating temperature range (C) -40 to 125 Shutdown current (ISD) (Typ) (uA) 1.4 Configurability Factory programmable, Software configurable
VQFN-HR (RNF) 26 18 mm² 4 x 4.5
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4B
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 0.6 V to 3.36 V
  • Four High-Efficiency Step-Down DC/DC Converter Cores:
    • Maximum Output Current: 10 A
  • Switching Frequency: 2 MHz
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface That Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function With Programmable Masking
  • Programmable Power-Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4B
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 0.6 V to 3.36 V
  • Four High-Efficiency Step-Down DC/DC Converter Cores:
    • Maximum Output Current: 10 A
  • Switching Frequency: 2 MHz
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface That Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function With Programmable Masking
  • Programmable Power-Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)

The LP8752x-Q1 device is designed to meet the power-management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC/DC converter cores, which are configured as a 4-phase output, 3-phase and 1-phase outputs, 2-phase and 2-phase outputs, one 2-phase and two 1-phase outputs, or four 1-phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.

The automatic pulse-width-modulation (PWM) to pulsed-frequency-modulation (PFM) operation (AUTO mode), together with the automatic phase adding and phase shedding, maximizes efficiency over a wide output-current range. The LP8752x-Q1 supports remote differential-voltage sensing for multiphase outputs to compensate IR drop between the regulator output and the point-of-load (POL) improving the accuracy of the output voltage. The switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP8752x-Q1 device supports load-current measurement without the addition of external current-sense resistors. The device also supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can include GPIO signals to control external regulators, load switches, and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output-voltage overshoot and in-rush current.

The LP8752x-Q1 device is designed to meet the power-management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC/DC converter cores, which are configured as a 4-phase output, 3-phase and 1-phase outputs, 2-phase and 2-phase outputs, one 2-phase and two 1-phase outputs, or four 1-phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.

The automatic pulse-width-modulation (PWM) to pulsed-frequency-modulation (PFM) operation (AUTO mode), together with the automatic phase adding and phase shedding, maximizes efficiency over a wide output-current range. The LP8752x-Q1 supports remote differential-voltage sensing for multiphase outputs to compensate IR drop between the regulator output and the point-of-load (POL) improving the accuracy of the output voltage. The switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP8752x-Q1 device supports load-current measurement without the addition of external current-sense resistors. The device also supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can include GPIO signals to control external regulators, load switches, and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output-voltage overshoot and in-rush current.

下载

您可能感兴趣的类似产品

open-in-new 产品比较
功能与比较器件相同且具有相同引脚。
LP87524-Q1 正在供货 具有集成开关的 LP87524-Q1 汽车类四输出降压转换器 The LP87525-Q1 is dual output and the LP87524-Q1 is quad output phase configuration of LP8752x-Q1 family.
LP87565-Q1 正在供货 具有集成开关的汽车类双路 8A 降压转换器 The LP87525-Q1 is a lower current variant of LP87565-Q1.

技术文档

star = TI 精选相关文档
未找到结果。请清除搜索,并重试。
显示全部 6 项
类型 标题 下载最新的英文版本 日期
* 数据表 LP8752x-Q1 10-A Buck Converter With Integrated Switches 数据表 2018年 3月 15日
应用手册 FlexPower PMIC 设备的优势 (Rev. B) 下载英文版本 (Rev.B) 2021年 5月 19日
用户指南 LP8752B-Q1 Technical Reference Manual 2020年 2月 3日
应用手册 Stability Considerations for LP8756x-Q1 and LP8752x-Q1 2019年 6月 4日
用户指南 Power Supply Design for Renesas R-Car M3 Using LP87565-Q1 and LP8732-Q1 2019年 5月 3日
用户指南 LP8752x-Q1 Programming Guide 2018年 10月 11日

设计与开发

有关其他条款或所需资源,请点击下面的任何链接来查看详情页面。

评估板

LP87565Q1EVM — 具有集成开关的双路输出 8A + 8A 降压转换器评估模块

LP87565Q1EVM 展示了德州仪器 (TI) 的集成电路 LP87565-Q1。

LP87565-Q1 是一款高性能多相位降压转换器,专为满足汽车应用中最新应用处理器的电源管理要求而设计。该器件包含 4 个降压直流/直流转换器内核,它们配置为单个四相降压转换器。LP87565-Q1 可以驱动高达 16A 的负载电流,集出色的解决方案尺寸和效率于一体。该器件可通过 PC 和提供的 GUI 进行控制。

可以对此 EVM 进行编程,以匹配 LP87565 或 LP87521 系列的任何配置。

现货
数量限制: 2
仿真模型

LP87525-Q1 PSpice Transient Model (Rev. A)

SNVMB00A.ZIP (318 KB) - PSpice Model
仿真模型

LP8756-Q1 and LP8752-Q1 SIMPLIS Model

SNVMBU8.ZIP (42 KB) - SIMPLIS Model
计算工具

PEET-GUI — PMIC Efficiency Estimator Tool (PEET)

PMIC 效率估算器工具 (PEET GUI) 是一个图形用户界面,可根据设计条件轻松评估 PMIC 直流/直流稳压器的效率。PEET GUI 可用于单独配置每个直流/直流稳压器,并以图形和表格两种格式提供实时效率和功耗数据。
原理图

LP8756x and LP8752x Design Checklist

SNVR480.ZIP (116 KB)
封装 引脚 下载
VQFN-HR (RNF) 26 了解详情

订购与质量

包含信息:
  • RoHS
  • REACH
  • 器件标识
  • 引脚镀层/焊球材料
  • MSL 等级/回流焊峰值温度
  • MTBF/FIT 估算
  • 材料成分
  • 认证摘要
  • 持续可靠性监测

推荐产品的参数、评估模块或参考设计可能与此 TI 产品相关

支持与培训

视频