产品详情

Cell chemistry Li-Ion/Li-Polymer, LiFePO4, NCM Number of series cells Single Cell Communication interface I2C Battery capacity (min) (mAh) 100 Battery capacity (max) (mAh) 32000 Implementation Pack External capacity indication None Features Configurable current limiter, Dynamic Z-Track™ technology, ECC authentication, Integrated Protector, SHA-256 Authentication Operating temperature range (°C) -40 to 85 Rating Catalog
Cell chemistry Li-Ion/Li-Polymer, LiFePO4, NCM Number of series cells Single Cell Communication interface I2C Battery capacity (min) (mAh) 100 Battery capacity (max) (mAh) 32000 Implementation Pack External capacity indication None Features Configurable current limiter, Dynamic Z-Track™ technology, ECC authentication, Integrated Protector, SHA-256 Authentication Operating temperature range (°C) -40 to 85 Rating Catalog
DSBGA (YAH) 15 5.4488 mm² (2.78 mm × 1.96 mm)
  • Fully integrated battery fuel gauge, linear battery charger, protector, and authenticator
  • Battery chemistries supported include Li-ion with LCO, NMC, or LFP cathodes
  • Battery fuel gauging based on patented Dynamic Z-Track technology
    • Automatically adjusts for aging, temperature, and rate-induced effects on the battery
  • Fully featured battery linear charger
    • CC/CV charging up to 2A with JEITA-compliant integrated Advanced Charge Algorithm (ACA)
    • Dynamic Power Path Management
      • MINSYS mode to ensure system voltage does not drop below target threshold while charging with a weak input
      • SUPPLEMENT mode with ultra fast switching time to ensure system does not brown out during loads while charging
    • Ideal diode (ID) mode during discharge to prevent voltage drop to system load
    • PACK+ terminal voltage tolerance of +24V with 1kΩ RPACK value
  • High-accuracy analog front end with two independent ADCs:
    • 18-bit low offset delta-sigma ADC for Coulomb counting with ±100mV input range
    • 16-bit delta-sigma ADC for cell voltage and internal and external temperature sensors
  • Programmable safety and protection:
    • Hardware-level protections
      • Over Voltage Protection (OVP)
      • Under Voltage Protection (UVP)
      • Over Current Charging (OCC)
      • Over Current Discharging (OCD)
      • Short Circuit Discharging (SCD)
    • Firmware-level protections
      • OVP, UVP, OCC, and OCD
      • Under Temperature (UT)
      • Over Temperature (OT)
      • FET Failure (FETF)
      • Charge Timeout (CTO)
  • ECC ECDSA authentication support with secure memory
  • True zero-volt charging to support dead battery charging
  • Integrated RTC with calendar and time of day
  • Ultra-compact, 15-ball DSBGA package (YAH)
  • Fully integrated battery fuel gauge, linear battery charger, protector, and authenticator
  • Battery chemistries supported include Li-ion with LCO, NMC, or LFP cathodes
  • Battery fuel gauging based on patented Dynamic Z-Track technology
    • Automatically adjusts for aging, temperature, and rate-induced effects on the battery
  • Fully featured battery linear charger
    • CC/CV charging up to 2A with JEITA-compliant integrated Advanced Charge Algorithm (ACA)
    • Dynamic Power Path Management
      • MINSYS mode to ensure system voltage does not drop below target threshold while charging with a weak input
      • SUPPLEMENT mode with ultra fast switching time to ensure system does not brown out during loads while charging
    • Ideal diode (ID) mode during discharge to prevent voltage drop to system load
    • PACK+ terminal voltage tolerance of +24V with 1kΩ RPACK value
  • High-accuracy analog front end with two independent ADCs:
    • 18-bit low offset delta-sigma ADC for Coulomb counting with ±100mV input range
    • 16-bit delta-sigma ADC for cell voltage and internal and external temperature sensors
  • Programmable safety and protection:
    • Hardware-level protections
      • Over Voltage Protection (OVP)
      • Under Voltage Protection (UVP)
      • Over Current Charging (OCC)
      • Over Current Discharging (OCD)
      • Short Circuit Discharging (SCD)
    • Firmware-level protections
      • OVP, UVP, OCC, and OCD
      • Under Temperature (UT)
      • Over Temperature (OT)
      • FET Failure (FETF)
      • Charge Timeout (CTO)
  • ECC ECDSA authentication support with secure memory
  • True zero-volt charging to support dead battery charging
  • Integrated RTC with calendar and time of day
  • Ultra-compact, 15-ball DSBGA package (YAH)

The Texas Instruments BQ27Z855 Dynamic Z-Trackgas gauge solution is a fully integrated, accurate 1-series cell gas gauge, JEITA-compliant linear battery charger, protection, and authentication solution.

The BQ27Z855 gas gauge communicates through an I2C compatible interface and combines an ultra-low power ARM M0 RISC processor, high accuracy analog measurement capabilities, integrated flash memory, high-side NMOS FET drivers, and ECC ECDSA authentication to provide a complete, high-performance battery management solution.

The Texas Instruments BQ27Z855 Dynamic Z-Trackgas gauge solution is a fully integrated, accurate 1-series cell gas gauge, JEITA-compliant linear battery charger, protection, and authentication solution.

The BQ27Z855 gas gauge communicates through an I2C compatible interface and combines an ultra-low power ARM M0 RISC processor, high accuracy analog measurement capabilities, integrated flash memory, high-side NMOS FET drivers, and ECC ECDSA authentication to provide a complete, high-performance battery management solution.

下载 观看带字幕的视频 视频

设计与开发

如需其他信息或资源,请点击以下任一标题进入详情页面查看(如有)。

评估板

BQ27Z855EVM — BQ27Z855 评估模块

BQ27Z855 评估模块 (EVM) 是一款系统级板,旨在帮助用户在系统内评估 BQ27Z855 电量监测计的功能。BQ27Z855 EVM 适用于电池组为 1 节串联电池(即单节串联电池)的应用。该 EVM 包含 BQ27Z855 电池电量监测计、低侧电流感应电阻器、集成式高侧保护器、ENAB 唤醒按钮、充电器唤醒按钮、线性电池充电器,以及其他接头选项,以便根据目标应用进行一定的改装。

用户指南: PDF | HTML
支持的产品和硬件
有库存
限制:
??asset.out-of-stock-ti_zh_CN??
无货
应用软件和框架

BQSTUDIO-TEST — Battery Management Studio (bqStudio) Software – Beta version downloads

Battery Management Studio (bqStudio) 提供一整套稳健的工具来帮助您评估、配置、测试 TI 电池管理产品以及利用其进行设计或以其他方式对其加以利用。这包括提供对寄存器和数据内存的完全访问,其中包括支持实时查看、绘制和记录轻松连接以发送命令、控制低级通信和 I/O,以及自动和指导支持配置、校准、执行学习周期以及生成有用的文件以将器件投入生产。

bqStudio 不支持 bq20xxx 和 bq30xxx 等旧产品。可从相应的产品页面下载特定的评估软件。您为 bqStudio 下载的最新化学物质更新程序也需要更新版 bqStudio。

支持的产品和硬件
固件

BQ27Z855-FW — BQ27Z855 device firmware

支持的产品和硬件
评估模块 (EVM) 用 GUI

BQSTUDIO-GUI — Battery Management Studio (bqStudio) Software - Web Based Version

Battery Management Studio (bqStudio) 提供一整套稳健的工具来帮助您评估、配置、测试 TI 电池管理产品以及利用其进行设计或以其他方式对其加以利用。这包括提供对寄存器和数据内存的完全访问,其中包括支持实时查看、绘制和记录轻松连接以发送命令、控制低级通信和 I/O,以及自动和指导支持配置、校准、执行学习周期以及生成有用的文件以将器件投入生产。

 

bqStudio-web 不支持 bq20xxx、bq30xxx 和 bq40xxx 等旧产品。可从相应的产品页面下载特定的评估软件。您为 bqStudio 下载的最新化学物质更新程序也需要更新版 bqStudio。

支持的产品和硬件
软件编程工具

BQ-BMS-PROGRAMMER-SW — Command line programmers for BQ products

BQ-BATTERY-PROGRAMMER-SW 软件开发套件 (SDK) 是一组强大的软件命令行工具,可在对使用 TI 电池管理产品的电池包进行编程、测试或组装的过程中提供帮助。该软件中的可执行文件支持用于 EV2300 通信收发器的 MKST-3P-ALT-EV2300 MKS Technology 替代产品。可执行文件可与单个站配合使用,但可以通过使用 MKS Technology Inc. 提供的其他软件和 GUI 扩展到多个站。本软件不支持多个站。

每个下载中有多个可执行文件,通常每个平台一个。还支持 BQ20xxx 和 BQ30xxx 等较旧的产品。提供了使用 C++ 编程语言 (...)

支持的产品和硬件
封装 引脚 CAD 符号、封装和 3D 模型
DSBGA (YAH) 15 Ultra Librarian

订购和质量

推荐产品可能包含与 TI 此产品相关的参数、评估模块或参考设计。

支持和培训

可获得 TI 工程师技术支持的 TI E2E™ 论坛

所有内容均由 TI 和社区贡献者按“原样”提供,并不构成 TI 规范。请参阅使用条款。

如果您对质量、包装或订购 TI 产品有疑问,请参阅 TI 支持。​​​​​​​​​​​​​​

视频