ZHCSMM7 April   2022 TUSB1004

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
    1.     说明
  3. 3 Revision History
  4. 4 Pin Configuration and Functions
  5. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Power Supply Characteristics
    6. 5.6  Control I/O DC Electrical Characteristics
    7. 5.7  USB Electrical Characteristics
    8. 5.8  Timing Requirements
    9. 5.9  Switching Characteristics
    10. 5.10 Typical Characteristics
  6. 6 Parameter Measurement Information
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 4-Level Inputs
      2. 7.3.2 USB Receiver Linear Equalization
        1. 7.3.2.1 Linear EQ Configuration
        2. 7.3.2.2 Full Adaptive Equalization
        3. 7.3.2.3 Fast Adaptive Equalization
      3. 7.3.3 USB Transmitter
        1. 7.3.3.1 Linearity VOD
        2. 7.3.3.2 Limited VOD
        3. 7.3.3.3 Transmit Equalization (Limited Redriver Mode Only)
      4. 7.3.4 USB 3.1 x2 Description
      5. 7.3.5 USB Polarity Inversion
      6. 7.3.6 Receiver Detect Control
    4. 7.4 Device Functional Modes
      1. 7.4.1 MODE Pin
      2. 7.4.2 Rx EQ Configuration in Pin-Strap Mode
      3. 7.4.3 USB 3.2 Power States
      4. 7.4.4 Disabling U1 and U2
    5. 7.5 Programming
      1. 7.5.1 Pseudocode Examples
        1. 7.5.1.1 Fixed EQ with Linear Redriver Mode
        2. 7.5.1.2 Fixed EQ with Limited Redriver Mode
        3. 7.5.1.3 Fast AEQ with Linear Redriver Mode
        4. 7.5.1.4 Fast AEQ with Limited Redriver Mode
        5. 7.5.1.5 Full AEQ with Linear Redriver Mode
        6. 7.5.1.6 Full AEQ with Limited Redriver Mode
      2. 7.5.2 TUSB1004 I2C Address Options
      3. 7.5.3 TUSB1004 I2C Target Behavior
    6. 7.6 Register Map
      1. 7.6.1 TUSB1004 Registers
  8. 8 Application and Implementation
    1. 8.1 Application Information
  9. 9 Typical Application
  10. 10Design Requirements
  11. 11Detailed Design Procedure
    1. 11.1 USB SSTX1/2 Receiver Configuration
    2. 11.2 USB CRX1/2 Receiver Configuration
      1. 11.2.1 Fixed Equalization
      2. 11.2.2 Full Adaptive Equalization
      3. 11.2.3 Fast Adaptive Equalization
  12. 12Application Curves
  13. 13Power Supply Recommendations
  14. 14Layout
    1. 14.1 Layout Guidelines
    2. 14.2 Layout Example
  15. 15Device and Documentation Support
    1. 15.1 接收文档更新通知
    2. 15.2 支持资源
    3. 15.3 Trademarks
    4. 15.4 Electrostatic Discharge Caution
    5. 15.5 术语表
  16. 16Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.5 Power Supply Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
PACTIVE-USB-2Ports Average active power
USB Only for both port1 and port2		 Link in U0 with GEN2 data transmission; EQ control pins = NC; PRBS7 pattern at
10 Gbps, VID = 1000 mVPP ; Linear redriver mode; LINR_L3;
EN = H;		 550 mW
PACTIVE-USB-1Port Average active power
USB Only for single port.		 Link in U0 with GEN2 data transmission; EQ control pins = NC; PRBS7 pattern at
10 Gbps, VID = 1000 mVPP ; LINR_L3;
EN = H;		 275 mW
PNC-USB-SLP# Average power with no connection with SLP_S0# No USB3.2 GEN2 device is connected to CTX1; EN = H; SLP_S0#; 0.13 mW
PNC-USB-1Port Average power with no connection No USB3.2 GEN2 device is connected to CTX1;
EN = H;		 1.5 mW
PNC-USB-2Ports Average power with no connection for both ports in disconnecton No USB3.2 device is connected to CTX1 and CTX2; 1.7 mW
PU2U3-2Ports Average power in U2/U3 for both ports Link in U2 or U3; EN = H; 2.8 mW
PU2U3-SLP# Average power in U2/U3 with SLP_S0# Link in U2 or U3; EN = H; SLP_S0# = L; 0.24 mW
PU2U3-1Port Average power in U2/U3 Link in U2 or U3; EN = H; 1.9 mW
PDISABLED-I2C Device Disabled power in I2C mode MODE = "F"; EN = H; CTLSEL = 0h; 0.108 mW
PDISABLED Device Disabled power in pin-strap MODE != "F"; EN = L; 0.130 mW