ZHCSMM7 April   2022 TUSB1004

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
    1.     说明
  3. 3 Revision History
  4. 4 Pin Configuration and Functions
  5. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Power Supply Characteristics
    6. 5.6  Control I/O DC Electrical Characteristics
    7. 5.7  USB Electrical Characteristics
    8. 5.8  Timing Requirements
    9. 5.9  Switching Characteristics
    10. 5.10 Typical Characteristics
  6. 6 Parameter Measurement Information
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 4-Level Inputs
      2. 7.3.2 USB Receiver Linear Equalization
        1. 7.3.2.1 Linear EQ Configuration
        2. 7.3.2.2 Full Adaptive Equalization
        3. 7.3.2.3 Fast Adaptive Equalization
      3. 7.3.3 USB Transmitter
        1. 7.3.3.1 Linearity VOD
        2. 7.3.3.2 Limited VOD
        3. 7.3.3.3 Transmit Equalization (Limited Redriver Mode Only)
      4. 7.3.4 USB 3.1 x2 Description
      5. 7.3.5 USB Polarity Inversion
      6. 7.3.6 Receiver Detect Control
    4. 7.4 Device Functional Modes
      1. 7.4.1 MODE Pin
      2. 7.4.2 Rx EQ Configuration in Pin-Strap Mode
      3. 7.4.3 USB 3.2 Power States
      4. 7.4.4 Disabling U1 and U2
    5. 7.5 Programming
      1. 7.5.1 Pseudocode Examples
        1. 7.5.1.1 Fixed EQ with Linear Redriver Mode
        2. 7.5.1.2 Fixed EQ with Limited Redriver Mode
        3. 7.5.1.3 Fast AEQ with Linear Redriver Mode
        4. 7.5.1.4 Fast AEQ with Limited Redriver Mode
        5. 7.5.1.5 Full AEQ with Linear Redriver Mode
        6. 7.5.1.6 Full AEQ with Limited Redriver Mode
      2. 7.5.2 TUSB1004 I2C Address Options
      3. 7.5.3 TUSB1004 I2C Target Behavior
    6. 7.6 Register Map
      1. 7.6.1 TUSB1004 Registers
  8. 8 Application and Implementation
    1. 8.1 Application Information
  9. 9 Typical Application
  10. 10Design Requirements
  11. 11Detailed Design Procedure
    1. 11.1 USB SSTX1/2 Receiver Configuration
    2. 11.2 USB CRX1/2 Receiver Configuration
      1. 11.2.1 Fixed Equalization
      2. 11.2.2 Full Adaptive Equalization
      3. 11.2.3 Fast Adaptive Equalization
  12. 12Application Curves
  13. 13Power Supply Recommendations
  14. 14Layout
    1. 14.1 Layout Guidelines
    2. 14.2 Layout Example
  15. 15Device and Documentation Support
    1. 15.1 接收文档更新通知
    2. 15.2 支持资源
    3. 15.3 Trademarks
    4. 15.4 Electrostatic Discharge Caution
    5. 15.5 术语表
  16. 16Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

11 Detailed Design Procedure

A typical usage of the TUSB1004 device is shown in Figure 11-1. The device can be configured either through its GPIO pins (SSEQ[1:0] and CEQ[1:0] pins) or through its I2C interface. In the example shown below, the TUSB1004 is configured in pin-strap mode with adaptive EQ (AEQ) enabled. The MODE pin is pull-down to GND through a 1-kΩ resistor. The AEQENZ is pull-down to GND which will enable AEQ for CRX1 and CRX2 receivers. Because AEQ is enabled, CEQ[1:0] pins can be left floating. The SSEQ[1:0] in this example is also floating but they need to configured to match the loss of the pre-channel (XAB).

GUID-20200916-CA0I-PHHJ-MWBS-HG5FJ0VM5XVT-low.gif Figure 11-1 Application Circuit