ZHCSMO6 June   2021 TPS92633

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Power Supply (SUPPLY)
        1. 7.3.1.1 Power-On Reset
        2. 7.3.1.2 Supply Current in Fault Mode
      2. 7.3.2  Enable and Shutdown (EN)
      3. 7.3.3  Reference Current (IREF)
      4. 7.3.4  Constant-Current Output and Setting (INx)
      5. 7.3.5  Analog Current Control (ICTRL)
        1. 7.3.5.1 Off-Board Brightness Binning Resistor
        2. 7.3.5.2 NTC Resistor
      6. 7.3.6  Thermal Sharing Resistor (OUTx and RESx)
      7. 7.3.7  PWM Control (PWMx)
      8. 7.3.8  Supply Control
      9. 7.3.9  Diagnostics
        1. 7.3.9.1 IREF Short-to-GND Detection
        2. 7.3.9.2 IREF Open Detection
        3. 7.3.9.3 LED Short-to-GND Detection
        4. 7.3.9.4 LED Open-Circuit Detection
        5. 7.3.9.5 Single LED Short-Circuit Detection (SLS_REF)
        6. 7.3.9.6 LED Open-Circuit and Single LED Short-Circuit Detection Enable (DIAGEN)
        7. 7.3.9.7 Low Dropout Operation
        8. 7.3.9.8 Over-Temperature Protection
      10. 7.3.10 FAULT Bus Output With One-Fails–All-Fail
      11. 7.3.11 FAULT Table
      12. 7.3.12 LED Fault Summary
      13. 7.3.13 IO Pins Inner Connection
    4. 7.4 Device Functional Modes
      1. 7.4.1 Undervoltage Lockout, V(SUPPLY) < V(POR_rising)
      2. 7.4.2 Normal Operation V(SUPPLY) ≥ 4.5 V
      3. 7.4.3 Low-Voltage Dropout Operation
      4. 7.4.4 Fault Mode
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 BCM Controlled Rear Lamp with One-Fails-All-Fail Setup
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
      2. 8.2.2 Independent PWM Controlled Rear Lamp with Off Board LED and Binning Resistor
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
        3. 8.2.2.3 Application Curves
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 接收文档更新通知
    2. 11.2 支持资源
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Detailed Design Procedure

STEP 1: Determine the reference current setting resistor, R(IREF), by using Equation 8.

Equation 8. GUID-6C55E1B2-63C5-470D-B74E-FBEFA2C1B199-low.gif

where

  • V(IREF) = 1.235 V (typical)
  • I(IREF) = 100 µA (recommended)

TI recommends 100 µA current for reference current, I(IREF) if the ICTRL resistor is placed in the same board with TPS92633. The calculated result for R(IREF) is 12.3 kΩ when I(IREF) = 100 µA.

STEP 2: Design the ICTRL resistor, R(ICTRL), for setting the regulation voltage, V(CS_REG) by using Equation 9.

Equation 9. GUID-1B1E56B7-8757-4864-BF4F-3379B5F72E2D-low.gif

where

  • V(CS_REG) = 100 mV (recommended)
  • I(IREF) = 100 µA (recommended)

TI recommends 100 mV for reference voltage across current sensing resistor, R(SNSx) if the ICTRL pin is not used for driving off-board binning resistor or NTC resistor. The calculated result for R(ICTRL) is 680 Ω when V(CS_REG) = 100 mV.

STEP 3: Determine the current sensing resistor, R(SNSx), by using Equation 10.

Equation 10. GUID-9AEC9A36-E681-42D7-AB48-0797DC6F05E0-low.gif

where

  • V(IREF) = 1.235 V (typical)
  • R(ICTRL) = 680 Ω
  • R(IREF) = 12.3 kΩ
  • I(OUTx_Tot) = 140 mA

According to design requirements, output current for each channel is same so that the R(SNS1) = R(SNS2) = R(SNS3) = 0.717 Ω. Two resistors in parallel are required to achieve equivalent 0.717-Ω resistance because 0.717 Ω is not a standard decade resistance value.

STEP 4: Design the current distribution between I(OUTx) and I(RESx), and calculate the current sharing resistor, R(RESx) by using Equation 11. The R(RESx) value actually decides the current distribution for I(OUTx) path and I(RESx) path, basic principle is to design the R(RESx) to consume appropriate 50% total power dissipation at typical supply operating voltage.

Equation 11. GUID-7CB7D84D-D701-4DF4-A0C8-CD82E6E47EAB-low.gif

where

  • V(SUPPLY) = 12 V (typical)
  • I(OUTx_Tot) = 140 mA

The calculated result for R(RESx) resistor value including R(RES1), R(RES2) and R(RES3) is 75 Ω when V(OUTx) is typical 3 × 2.2 V = 6.6 V.

STEP 5: Design the single-LED short-circuit threshold voltage and calculate the value of R(SLS_REF) resistor for setting single-LED short-circuit threshold by using Equation 12.

The total forward voltage for three LEDs in serial is 3 × 2.5 V = 7.5-V maximum and 3 × 1.9 V = 5.7-V minimum. Once anyone of three LEDs is defective with short-circuit behavior, the total forward voltage for remaining two LEDs in serial is 2 × 2.5 V = 5-V maximum and 2 × 1.9 V = 3.8-V minimum. So the 5.3 V is selected to be threshold for single-LED short-circuit, V(SLS_th_falling).

Equation 12. GUID-1F9B686A-5015-4379-B11F-1218D0717EB0-low.gif

where

  • V(IREF) = 1.235 V (typical)
  • R(IREF) = 12.3 kΩ
  • N(OUT) = 4
  • N(SLS_REF) = 1

The calculated result for R(SLS_REF) is 13.3 kΩ for V(SLS_th_falling) is 5.34 V.

STEP 6: Design the threshold voltage of SUPPLY to enable the LED open-circuit and single-LED short-circuit diagnostics, and calculate voltage divider resistor value for R1 and R2 on DIAGEN pin.

The maximum forward voltage of LED-string is 3 × 2.5 V = 7.5 V. To avoid the open-circuit fault or single-LED short-circuit reported in low-dropout operation conditions, additional headroom between SUPPLY and OUTx needs to be considered. The TPS92633 device must disable open-circuit detection and single-LED short-circuit detection when the supply voltage is below LED-string maximum forward voltage plus V(OPEN_th_rising) and V(CS_REG). The voltage divider resistor, R1 and R2 value can be calculated by Equation 13.

Equation 13. GUID-6B29B95C-25ED-4458-809B-E90C8BB2EA2E-low.gif

where

  • V(OPEN_th_rising) = 210 mV (maximum)
  • V(CS_REG) = 100 mV
  • VIL(DIAGEN) = 1.045 V (minimum)
  • R2 = 10 kΩ (recommended)

The calculated result for R1 is 64.9 kΩ when V(OUTx) maximum voltage is 7.5 V and V(CS_REG) is 100 mV.

STEP 7: Design the threshold voltage of SUPPLY to turn on and off each channel of LED, and calculate voltage divider resistor value for R3 and R4 on PWM input pin.

The minimum forward voltage of LED-string is 3 × 1.9 V = 5.7 V. To make sure the current output on each of LED-string is normal, each LED-string needs to be turned off when SUPPLY voltage is lower than LED minimum required forward voltage plus dropout voltage between INx to OUTx and V(CS_REG). The voltage divider resistor, R3 and R4 value can be calculated by Equation 14.

Equation 14. GUID-10EFBFB5-7121-4DB3-91AD-ACD7E7BC2911-low.gif

where

  • V(DROPOUT) = 300 mV (typical)
  • V(CS_REG) = 100 mV
  • VIH(PWM) = 1.26 V (maximum)
  • R4 = 10 kΩ (recommended)

The calculated result for R3 is 38.3 kΩ when V(OUTx) minimum voltage is 5.7 V and V(CS_REG) is 100 mV.