ZHCSDX6 July   2015 TPS65400-Q1

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 修订历史记录
  5. 5 说明（续）
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 System Characteristics
    7. 7.7 Operational Parameters
    8. 7.8 Package Dissipation Ratings
    9. 7.9 Typical Characteristics: System Efficiency
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1  Startup Timing and Power Sequencing
        1. 8.3.1.1 Startup Timing
        2. 8.3.1.2 External Sequencing
        3. 8.3.1.3 Internal Sequencing
      2. 8.3.2  UVLO and Precision Enables
      3. 8.3.3  Soft-Start and Prebiased Startup
        1. 8.3.3.1 Analog Soft-Start (Default) and Digital Soft-Start
        2. 8.3.3.2 Soft-Start Capacitor Selection
      4. 8.3.4  PWM Switching Frequency Selection
      5. 8.3.5  Clock Synchronization
      6. 8.3.6  Phase Interleaving
      7. 8.3.7  Fault Handling
      8. 8.3.8  OCP for SW1 to SW4
      9. 8.3.9  Overcurrent Protection for SW1 to SW4 in Current Sharing Operation
      10. 8.3.10 Recovery on Power Loss
      11. 8.3.11 Feedback Compensation
      12. 8.3.12 Adjusting Output Voltage
      13. 8.3.13 Digital Interface - PMBus
      14. 8.3.14 Initial Configuration
    4. 8.4 Device Functional Modes
      1. 8.4.1 CCM Operation Mode
      2. 8.4.2 CCM/DCM Operation Mode
      3. 8.4.3 Current Sharing Mode
    5. 8.5 Register Maps
      1. 8.5.1 PMBus
        1. 8.5.1.1 Overview
        2. 8.5.1.2 PMBus Protocol
          1. 8.5.1.2.1  PMBus Protocol
          2. 8.5.1.2.2  Transactions (No PEC)
          3. 8.5.1.2.3  Addressing
          4. 8.5.1.2.4  Startup
          5. 8.5.1.2.5  Bus Speed
          6. 8.5.1.2.6  I2CALERT Terminal
          7. 8.5.1.2.7  CONTROL Terminal
          8. 8.5.1.2.8  Packet Error Checking
          9. 8.5.1.2.9  Group Commands
          10. 8.5.1.2.10 Unsupported Features
      2. 8.5.2 PMBus Register Descriptions
        1. 8.5.2.1 Overview
        2. 8.5.2.2 Memory Model
        3. 8.5.2.3 Data Formats
        4. 8.5.2.4 Fault Monitoring
      3. 8.5.3 PMBus Core Commands
        1. 8.5.3.1  (00h) PAGE
        2. 8.5.3.2  (01h) OPERATION
        3. 8.5.3.3  (03h) CLEAR_FAULTS
        4. 8.5.3.4  (10h) WRITE_PROTECT
        5. 8.5.3.5  (11h) STORE_DEFAULT_ALL
        6. 8.5.3.6  (19h) CAPABILITY
        7. 8.5.3.7  (78h) STATUS_BYTE
        8. 8.5.3.8  (79h) STATUS_WORD
        9. 8.5.3.9  (7Ah) STATUS_VOUT
        10. 8.5.3.10 (80h) STATUS_MFR_SPECIFIC
        11. 8.5.3.11 (98h) PMBUS_REVISION
        12. 8.5.3.12 (ADh) IC_DEVICE_ID
        13. 8.5.3.13 (AEh) IC_DEVICE_REV
      4. 8.5.4 Manufacturer-Specific Commands
        1. 8.5.4.1  (D0h) USER_DATA_BYTE_00
        2. 8.5.4.2  (D1h) USER_DATA_BYTE_01
        3. 8.5.4.3  (D2h) PIN_CONFIG_00
        4. 8.5.4.4  (D3h) PIN_CONFIG_01
        5. 8.5.4.5  (D4h) SEQUENCE_CONFIG
        6. 8.5.4.6  (D5h) SEQUENCE_ORDER
        7. 8.5.4.7  (D6h) IOUT_MODE
        8. 8.5.4.8  (D7h) FREQUENCY_PHASE
        9. 8.5.4.9  (D8h) VREF_COMMAND
        10. 8.5.4.10 (D9h) IOUT_MAX
        11. 8.5.4.11 (DAh) USER_RAM_00
        12. 8.5.4.12 (DBh) SOFT_RESET
        13. 8.5.4.13 (DCh) RESET_DELAY
        14. 8.5.4.14 (DDh) TON_TOFF_DELAY
        15. 8.5.4.15 (DEh) TON_TRANSITION_RATE
        16. 8.5.4.16 (DFh) VREF_TRANSITION_RATE
        17. 8.5.4.17 (F0h) SLOPE_COMPENSATION
        18. 8.5.4.18 (F1h) ISENSE_GAIN
        19. 8.5.4.19 (FCh) DEVICE_CODE
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Internal Operation Typical Application
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Component Selection
            1. 9.2.1.2.1.1 Output Inductor Selection
            2. 9.2.1.2.1.2 Output Capacitor Selection
          2. 9.2.1.2.2 Internal Operation With Some Switchers Disabled
          3. 9.2.1.2.3 Internal Operation With All Switchers Enabled
          4. 9.2.1.2.4 Example Configuration
          5. 9.2.1.2.5 Unused Switchers
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Current Sharing Typical Application
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
          1. 9.2.2.2.1 Current Sharing Timing Example
      3. 9.2.3 External Sequencing Application
        1. 9.2.3.1 Design Requirements
        2. 9.2.3.2 Detailed Design Procedure
          1. 9.2.3.2.1 External Sequencing Through PG Pins
          2. 9.2.3.2.2 External Sequencing Through SW
          3. 9.2.3.2.3 Example Configuration
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 文档支持
      1. 12.1.1 相关文档
      2. 12.1.2 相关器件
    2. 12.2 社区资源
    3. 12.3 商标
    4. 12.4 静电放电警告
    5. 12.5 Glossary
  13. 13机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7 Specifications

7.1 Absolute Maximum Ratings

over operating free-air temperature (unless otherwise noted) (1)
MIN MAX UNIT
Input voltage PVIN1, PVIN2, PVIN3, PVIN4, VIN –0.3 20 V
CB1, CB2, CB3, CB4 referenced to SWx –0.3 7.5
ENSW1, ENSW2, ENSW3, ENSW4, SCL, SDA, CLK_OUT, VFB1, VFB2, VFB3, VFB4, RST_N, SCL, SDA, I2CALERT, CLK_OUT, I2CADDR, RCLOCK_SYNC –0.3 VDDD or 3.6
SW1, SW2, SW3, SW4 –1 20
VDDA, VDDG –0.3 7.5
PGOOD, SS1/PG1, SS2/PG2, SS3/PG3, SS4/PG4, COMP1, COMP2, COMP3, COMP4, CE –0.3 VDDA or 7.5
VDDD –0.3 3.6
TJ(max) Junction temperature 150 °C
Maximum lead temperature (soldering, 10 s) 260 °C
Tstg Storage temperature –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

7.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per AEC Q100-002(1) ±2000 V
Charged-device model (CDM), per AEC Q100-011 All pins ±500
Corner pins (1, 12, 13, 24, 25, 36, 37, and 48) ±750
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
VIN1, VIN2, VIN3, VIN4 Input voltage range 4.5 18 V
IOUT1, IOUT2 Load current 0 4 A
IOUT3, IOUT4 Load current 0 2 A
VFB1, VFB2, VFB3, VFB4 Voltage feedback 0.6 1.87 V
TJ Junction temperature range –40 125 °C

7.4 Thermal Information

THERMAL METRIC(1) TPS65400-Q1 UNIT
RGZ (VQFN)
48 PINS
RθJA Junction-to-ambient thermal resistance 29.8 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 14.9 °C/W
RθJB Junction-to-board thermal resistance 6.3 °C/W
ψJT Junction-to-top characterization parameter 0.2 °C/W
ψJB Junction-to-board characterization parameter 6.3 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 0.8 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953.

7.5 Electrical Characteristics

VIN = 12 V, FSW = 500 kHz, TJ = –40°C to 125°C, typical values are at TJ = 25°C, unless otherwise noted
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SWITCHER 1 AND SWITCHER 2
Ilimit1, Ilimit2 SW1, SW2 high-side current limit adjustment range 2 6 A
Ilimit-accuracy Accuracy to nominal current limit value Ilimit = 4 A, 5 A, 6 A –25% 25%
Rdson HS SW1, SW2 HS Rds(on) 66 mΩ
Rdson LS SW1, SW2 LS Rds(on) 42 mΩ
SWITCHER 3 AND SWITCHER 4
Ilimit3, Ilimit4 SW3 and SW4 current limit 0.5 3 A
Ilimit accuracy Accuracy to nominal current limit value Ilimit = 1 A, 2 A, 3 A –25% 25%
Rdson HS SW3 and SW4 HS Rds(on) 120 mΩ
Rdson LS SW3/4 LS Rds(on) 90 mΩ
FEEDBACK AND ERROR AMPLIFIERS FOR SW1 – SW4
VFB Accuracy VREF = 1 V –1% 1%
VREFn Error amplifier reference voltage Default value 800 mV
VREF_STEP I2C programmable VREF step size 10 mV
Gm Error amplifier transconductance 95 133 165 µS
Isink Sink 12 µA
Isource Source 12 µA
PWM SWITCHING CHARACTERISTICS
Phase_err12(1) Phase error between SW1 and SW2 Fsw = 1.1 MHz 5⁰
Phase_err34(1) Phase error between SW3 and SW4 Fsw = 1.1 MHz 5⁰
Fsw Resistor-configurable PWM switching configuration 275 2200 kHz
Fsw-accuracy PWM switching frequency accuracy ROSC = 165 kΩ
(Fsw = 1.1 MHz)		 –10% 10%
Vrclock_sync Voltage reference for RCLOCK_SYNC 0.8 V
tON_min Lower duty cycle limit 80 150 ns
tOFF_min Minimum off-time limit (constrains the maximum achievable duty cycle) 150 ns
CLOCK SYNC
V_HSYNC High signal threshold 2.6 V
V_LSYNC Low signal threshold 1 V
ICLKOUT Max current sink/source for CLK_OUT 2 mA
tmin_SYNC Minimum detectable time for sync pulse 150 ns
FSYNC Frequency synchronization range 275 2200 kHz
TSYNC_DELAY Delay between input pulse to RCLOCK_SYNC and rising edge of CLK_OUT and PWM output 20 ns
TIMING CHARACTERISTICS
trestart Delay for restart during repeated OCP condition 20 ms
INTERNAL REGULATORS AND UVLO
VDDA Internal subregulator output Vin > 6.6 V 6.1 V
4.5 V < Vin 6.6 V Vin – 0.1
VDDD Output of internal subregulator 3.2 V
VDDG Output of Internal regulator for gate drivers Vin > 6.6 V 6.1 V
4.5 V < Vin 6.6 V Vin – 0.1
IVIN Quiescent non-switching, no load current CE high, VFB >> VREF, (no switching) 8 mA
ISD Quiescent shutdown current CE low 12 27 µA
VIN_UVLO Input voltage UVLO Rising 4.25 4.48 V
VIN_UVLO Input voltage UVLO Falling 3.4 3.75 V
PGOOD, ENSWx, RST_N, SSx, PG
R_LPGOOD Resistance of PGOOD outputs when low 500 Ω
V_OLPGOOD Logic output low voltage I_OL = 100 µA 0.1 V
ISS Soft-start current 4.1 5.6 7.3 µA
VEN_H Enable logic high threshold (for ENSW1, ENSW2, ENSW3, ENSW4) VEN rising 1.12 1.20 1.28 V
VEN_L Enable logic low threshold (for ENSW1, ENSW2, ENSW3, ENSW4) VEN falling 0.97 1.07 V
VEN_HYS Enable hysteresis (for ENSW1, ENSW2, ENSW3, ENSW4) 130 mV
IEN ENSWx pin pullup current VEN = 0 2 µA
ICE CE pin pullup current VCE = 0 2 µA
VIH_CE Logic input high for CE 1.3 V
VIL_CE Logic input low CE 0.4 V
VIH_RSTN Logic input high RST_N 1.3 V
VIL_RSTN Logic input low RST_N 0.4 V
I2C MODULE (SDA, SCL, I2CALERT, I2CADDR)
V_ILI2C Logic input low SCL, SDA 0.8 V
V_IHI2C Logic input high for SCL, SDA 2.1 V
R_LI2C ON resistance of I2C pins (SDA,SCL,I2CALERT) to GND I2CALERT = 1 85 Ω
V_OLI2C Logic output low voltage for SCL,SDA,I2CALERT pins I_OL = 350 µA 0.1 V
ILEAK Input leakage current SDA, SCL = 3.3 V 1 µA
II2CADDR Source current of I2CADDR pin VDDD = 3.3 V, VIN > 4.5 V 20 uA
tTIMEOUT Timeout detection on SDA or SCL low 30 ms
tTIMEOUT_PULSE Duration of timeout pulse on I2CALERT 200 µs
FAULTS
TTSD(2) Thermal shutdown threshold 160 ⁰C
TTSD_restart(2) Thermal shutdown hysteresis 20 ⁰C
VFB_OVP OVP threshold rising (fault latched, PGOOD asserted) 0.6V < VREF < 1.87 V 111 % of VREF
OVP threshold falling (fault cleared, PGOOD deasserted) 0.6 V < VREF < 1.87 V 104 % of VREF
tOVPSDOWN Time after OVP before protection activation and PGOOD fall 55 95 µs
VFB UVP Undervoltage threshold (PGOOD deasserted) 0.6 V < VREF < 1.87 V 92 % of VREF
Undervoltage Threshold (PGOOD asserted) 0.6 V < VREF < 1.87 V 83 % of VREF
tUVPSDOWN Time after UVP before PGOOD fall 55 95 µs
(1) Specified by design.
(2) Specified by lab validation.

7.6 System Characteristics

The following specification table entries are specified by the design (component values provided in the typical application circuit are used). These parameters are not specified by production testing. Minimum and Max values apply over the full operating ambient temperature range (–40°C ≤ TJ ≤ 125°C), over the VIN range = 5 to 12 V, and IOUT range unless otherwise specified. L = 3.3 µH, DCR = 10.4 mΩ, VOUT = 1.2 V, 1% FB resistor.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VLINEREG Line regulation 0.1 %/V
VLOADREG Load regulation 0.1 %/A
tr VOUT step duration (tr) For 50-mV step 30 µs
ts VOUT step settling time (ts) For 50-mV step 30 µs
VOVUV VOUT step overshoot/undershoot For 50-mV step 6 mV
Efficiency (SW1 and SW2) Vin = 5 V, Vo = 1.2 V, Iout = 4 A,
ƒsw = 500 kHz		 77%
Vin = 12 V, Vo = 1.2 V Iout = 4 A,
ƒsw = 500 kHz		 76%
Efficiency (SW3 and SW4) Vin = 5 V, Vo = 1.2 V, Iout = 2 A,
ƒsw= 500 kHz		 77%
Vin = 12 V, Vo = 1.2 V Iout = 2 A,
ƒsw = 500 kHz		 74%
IOUTmatch Average ((1)) current sharing accuracy (SW1 and SW2, SW3 and SW4) Iload = IOUTmax 20%
IPKmatch Peak current ((2)) sharing accuracy (SW1 and SW2, SW3 and SW4) Iload = IOUTmax 20%
tacc Timing accuracy for delays and restarts –10% 10%
treset_delay Time after RSTn or CE is released for power sequence to begin Default value 1 ms
treset_delay_max0 Minimum delay after reset is released for power sequence to begin treset_delay set to 0 ms 1.1 ms
(1) Average current sharing accuracy is highly dependent on the matching of the inductor and capacitor.
(2) Peak current sharing accuracy refers to the max inductor current in each phase.

7.7 Operational Parameters

Values recommended that ensure proper system behavior
PARAMETER MIN TYP MAX UNIT
CA Stabilization capacitor to be connected to VDDA 4.7 µF
CD Stabilization capacitor to be connected to VDDD 3.3 µF
CG Stabilization capacitor to be connected to VDDG 10 µF
Vin1, Vin2, Vin3, Vin4 SW1 to SW4 input voltage 4.5 18 V
Vout1, Vout2, Vout3, Vout4 SW1 to SW4 output voltage 0.6 90% of Vin V

7.8 Package Dissipation Ratings(1)

PACKAGE RθJA (°C/W) TA = 25°C TA = 55°C TA = 85°C
RGZ 29.8 4.5 W 3.14 W 1.77 W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953.

7.9 Typical Characteristics: System Efficiency

TPS65400-Q1 D001_SLVSCQ9.gif
With 500 kHz and XAL6060-472 4.7-µH, 13.2-mΩ inductor
Figure 1. Buck1 and Buck2 Power Efficiency, VIN = 12 V
TPS65400-Q1 D004_SLVSCQ9.gif
With 500 kHz FSW and 4.7-µH, 34-mΩ inductor
Figure 3. Buck3 and Buck4 Power Efficiency, VIN = 12 V
TPS65400-Q1 D002_SLVSCQ9.gif
With 500 kHz and XAL6060-472 4.7-µH, 13.2-mΩ inductor
Figure 2. Buck1 and Buck2 Power Efficiency, VIN = 5 V
TPS65400-Q1 D005_SLVSCQ9.gif
With 500 kHz FSW and 4.7-µH, 34-mΩ inductor
Figure 4. Buck3 and Buck4 Power Efficiency, VIN = 5 V