SLVS841F November   2008  – August 2016 TPS2552 , TPS2552-1 , TPS2553 , TPS2553-1

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. Parameter Measurement Information
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Overcurrent Conditions
      2. 9.3.2 Reverse-Voltage Protection
      3. 9.3.3 FAULT Response
      4. 9.3.4 Undervoltage Lockout (UVLO)
      5. 9.3.5 ENABLE (EN or EN)
      6. 9.3.6 Thermal Sense
    4. 9.4 Device Functional Modes
    5. 9.5 Programming
      1. 9.5.1 Programming the Current-Limit Threshold
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Constant-Current vs Latch-Off Operation and Impact on Output Voltage
    2. 10.2 Typical Applications
      1. 10.2.1 Two-Level Current-Limit Circuit
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedures
          1. 10.2.1.2.1 Designing Above a Minimum Current Limit
          2. 10.2.1.2.2 Designing Below a Maximum Current Limit
          3. 10.2.1.2.3 Accounting for Resistor Tolerance
          4. 10.2.1.2.4 Input and Output Capacitance
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Auto-Retry Functionality
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
      3. 10.2.3 Typical Application as USB Power Switch
        1. 10.2.3.1 Design Requirements
          1. 10.2.3.1.1 USB Power-Distribution Requirements
        2. 10.2.3.2 Detailed Design Procedure
          1. 10.2.3.2.1 Universal Serial Bus (USB) Power-Distribution Requirements
  11. 11Power Supply Recommendations
    1. 11.1 Self-Powered and Bus-Powered Hubs
    2. 11.2 Low-Power Bus-Powered and High-Power Bus-Powered Functions
    3. 11.3 Power Dissipation and Junction Temperature
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
    2. 13.2 Related Links
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Community Resources
    5. 13.5 Trademarks
    6. 13.6 Electrostatic Discharge Caution
    7. 13.7 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • DBV|6
  • DRV|6
散热焊盘机械数据 (封装 | 引脚)
订购信息

4 Revision History

Changes from E Revision (February 2012) to F Revision

  • Added ESD Rating table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section Go
  • Changed 1300 mA to 1700 mA in the adjustable current limit bullet under the Features sectionGo
  • Changed from 1.2 A to 1.5 AGo

Changes from D Revision (June 2011) to E Revision

  • Changed VEN to VEN in Recommended Operating ConditionsGo
  • Changed VEN to VEN in Recommended Operating ConditionsGo

Changes from C Revision (September 2009) to D Revision

  • Changed From: Fast Overcurrent Response - 2-µS (typ) To: Fast Overcurrent Response - 2-µs (typ) in the FeaturesGo
  • Added text To Feature - UL Listed "and NEMKO IEC60950-1-am1 ed2.0"Go
  • Added Features Item "See the TI Switch Portfoilo"Go
  • Changed the DEVICE INFORMATION table, and Deleted Note 3Go
  • Added ESD-system level (contact/air) to the ABS MAX table, and Added Note 3Go
  • Added text to the REVERSE-VOLTAGE PROTECTION section: "A reverse.....when this occurs."Go

Changes from B Revision (February 2009) to C Revision

  • Added Feature - Up to 1.5 A Maximum Load CurrentGo
  • Changed 1.3 A (typ) To: 1.7 A (typ)Go
  • Added Text - and provide up to 1.5 A of continuous load currentGo
  • Changed From: 19.1 kΩ ≤ RILIM ≤ 232 kΩ To: 15 kΩ ≤ RILIM ≤ 232 kΩ.Go
  • Changed IOUT values for 1.2A and 1.5AGo
  • Changed TJ values for 1.2A and 1.5AGo
  • Added RILIM = 15 kΩ optionGo
  • Changed Text From: current-limit threshold between 75 mA and 1.3 A (typ) To: current-limit threshold between 75 mA and 1.7 A (typ)Go
  • Changed Text From: The recommended 1% resistor range for RILIM is 19.1 kΩ ≤ RILIM ≤ 232 kΩ to ensure stability To: The recommended 1% resistor range for RILIM is 15 kΩ ≤ RILIM ≤ 232 kΩ to ensure stabilityGo
  • Changed Figure 23 - Current-Limit Threshold vs RILIM Go
  • Changed Table 2 - added rows for Current Limit of 1400 to 1700Go

Changes from A Revision (December 2008) to B Revision

  • Added To Features - UL Listed – File No. E169910Go
  • Changed Figure 17 Ttitle From: Current Limit Threshold Vs RILM Go
  • Changed Figure 18 Ttitle From: Current Limit Threshold Vs RILM Go

Changes from * Revision (November 2008) to A Revision

  • Changed Title from: Adjustable Current-Limited Power-Distribution Switches to: Precision Adjustable Current-Limited Power-Distribution SwitchesGo