SLOS670B November   2010  – December 2016 TAS5727

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Thermal Information
    5. 8.5  DC Electrical Characteristics
    6. 8.6  AC Electrical Characteristics (BTL, PBTL)
    7. 8.7  PLL Input Parameters and External Filter Components
    8. 8.8  Serial Audio Ports Slave Mode
    9. 8.9  I2C Serial Control Port Operation
    10. 8.10 Reset Timing (RESET)
    11. 8.11 Typical Characteristics
  9. 9 Parameter Measurement Information
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagrams
    3. 10.3 Feature Description
      1. 10.3.1  Power Supply
      2. 10.3.2  I2C Address Selection and Fault Output
        1. 10.3.2.1 I2C Chip Select
        2. 10.3.2.2 I2C Device Address Change Procedure
        3. 10.3.2.3 Fault Indication
      3. 10.3.3  Device Protection Systems
        1. 10.3.3.1 Overcurrent (OC) Protection With Current Limiting
        2. 10.3.3.2 Overtemperature Protection
        3. 10.3.3.3 Undervoltage Protection (UVP) and Power-On Reset (POR)
      4. 10.3.4  Clock, Auto Detection, and PLL
      5. 10.3.5  PWM Section
      6. 10.3.6  SSTIMER Functionality
      7. 10.3.7  Single-Filter PBTL Mode
      8. 10.3.8  I2C Serial Control Interface
        1. 10.3.8.1 General I2C Operation
        2. 10.3.8.2 Single- and Multiple-Byte Transfers
        3. 10.3.8.3 Single-Byte Write
        4. 10.3.8.4 Multiple-Byte Write
        5. 10.3.8.5 Single-Byte Read
        6. 10.3.8.6 Multiple-Byte Read
      9. 10.3.9  Audio Serial Interface
      10. 10.3.10 Serial Interface Control and Timing
        1. 10.3.10.1 I2S Timing
        2. 10.3.10.2 Left-Justified
        3. 10.3.10.3 Right-Justified
      11. 10.3.11 Dynamic Range Control (DRC)
      12. 10.3.12 PWM Level Meter
    4. 10.4 Device Functional Modes
      1. 10.4.1 Stereo BTL Mode
      2. 10.4.2 Mono PBTL Mode
    5. 10.5 Programming
      1. 10.5.1 26-Bit 3.23 Number Format
    6. 10.6 Register Maps
      1. 10.6.1  Clock Control Register (0x00)
      2. 10.6.2  Device Id Register (0x01)
      3. 10.6.3  Error Status Register (0x02)
      4. 10.6.4  System Control Register 1 (0x03)
      5. 10.6.5  Serial Data Interface Register (0x04)
      6. 10.6.6  System Control Register 2 (0x05)
      7. 10.6.7  Soft Mute Register (0x06)
      8. 10.6.8  Volume Registers (0x07, 0x08, 0x09)
      9. 10.6.9  Volume Configuration Register (0x0E)
      10. 10.6.10 Modulation Limit Register (0x10)
      11. 10.6.11 Interchannel Delay Registers (0x11, 0x12, 0x13, and 0x14)
      12. 10.6.12 PWM Shutdown Group Register (0x19)
      13. 10.6.13 Start/Stop Period Register (0x1A)
      14. 10.6.14 Oscillator Trim Register (0x1B)
      15. 10.6.15 BKND_ERR Register (0x1C)
      16. 10.6.16 Input Multiplexer Register (0x20)
      17. 10.6.17 Channel 4 Source Select Register (0x21)
      18. 10.6.18 PWM Output MUX Register (0x25)
      19. 10.6.19 DRC Control Register (0x46)
      20. 10.6.20 PWM Switching Rate Control Register (0x4F)
      21. 10.6.21 Bank Switch and EQ Control (0x50)
  11. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Applications
      1. 11.2.1 Stereo Stereo Bridge Tied Load Application
        1. 11.2.1.1 Design Requirements
        2. 11.2.1.2 Detailed Design Procedure
          1. 11.2.1.2.1 Component Selection and Hardware Connections
          2. 11.2.1.2.2 I2C Pullup Resistors
          3. 11.2.1.2.3 Digital I/O Connectivity
          4. 11.2.1.2.4 Recommended Start-Up and Shutdown Procedures
            1. 11.2.1.2.4.1 Initialization Sequence
            2. 11.2.1.2.4.2 Normal Operation
            3. 11.2.1.2.4.3 Shutdown Sequence
            4. 11.2.1.2.4.4 Power-Down Sequence
        3. 11.2.1.3 Application Curves
      2. 11.2.2 Mono Parallel Bridge Tied Load Application
        1. 11.2.2.1 Design Requirements
        2. 11.2.2.2 Detailed Design Procedure
        3. 11.2.2.3 Application Curves
  12. 12Power Supply Recommendations
    1. 12.1 DVDD and AVDD Supplies
    2. 12.2 PVDD Power Supply
  13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Layout Example
  14. 14Device and Documentation Support
    1. 14.1 Device Support
      1. 14.1.1 Development Support
    2. 14.2 Documentation Support
      1. 14.2.1 Related Documentation
    3. 14.3 Receiving Notification of Documentation Updates
    4. 14.4 Community Resources
    5. 14.5 Trademarks
    6. 14.6 Electrostatic Discharge Caution
    7. 14.7 Glossary
  15. 15Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7 Pin Configuration and Functions

PHP Package
48-Pin HTQFP
Top View

Pin Functions

PIN TYPE(1) 5-V TOLERANT TERMINATION(2) DESCRIPTION
NAME NO.
AGND 30 P Local analog ground for power stage
A_SEL_FAULT 14 DIO This pin is monitored on the rising edge of RESET. A value of 0 (15-kΩ pulldown) sets the I2C device address to 0x54 and a value of 1 (15-kΩ pullup) sets it to 0x56. this dual-function pin can be programmed to output internal power-stage errors.
AVDD 13 P 3.3-V analog power supply
AVSS 9 P Analog 3.3-V supply ground
BST_A 4 P High-side bootstrap supply for half-bridge A
BST_B 43 P High-side bootstrap supply for half-bridge B
BST_C 42 P High-side bootstrap supply for half-bridge C
BST_D 33 P High-side bootstrap supply for half-bridge D
DVDD 27 P 3.3-V digital power supply
DVSS 28 P Digital ground
DVSSO 17 P Oscillator ground
GND 29 P Analog ground for power stage
GVDD_OUT 32 P Gate drive internal regulator output
LRCLK 20 DI 5-V Pulldown Input serial audio data left and right clock (sample-rate clock)
MCLK 15 DI 5-V Pulldown Master clock input
NC 5, 7, 40, 41, 44, 45 – No connect
OSC_RES 16 AO Oscillator trim resistor. Connect an 18.2-kΩ, 1% resistor to DVSSO.
OUT_A 1 O Output, half-bridge A
OUT_B 46 O Output, half-bridge B
OUT_C 39 O Output, half-bridge C
OUT_D 36 O Output, half-bridge D
PBTL 8 DI Low means BTL mode; high means PBTL mode. Information goes directly to power stage.
PDN 19 DI 5-V Pullup Power down, active-low. PDN prepares the device for loss of power supplies by shutting down the noise shaper and initiating the PWM stop sequence.
PGND_AB 47, 48 P Power ground for half-bridges A and B
PGND_CD 37, 38 P Power ground for half-bridges C and D
PLL_FLTM 10 AO PLL negative loop-filter terminal
PLL_FLTP 11 AO PLL positive loop-filter terminal
PVDD_AB 2, 3 P Power-supply input for half-bridge output A
PVDD_CD 34, 35 P Power-supply input for half-bridge output D
RESET 25 DI 5-V Pullup Reset, active-low. A system reset is generated by applying a logic low to this pin. RESET is an asynchronous control signal that restores the DAP to its default conditions and places the PWM in the hard-mute (high-impedance) state.
SCL 24 DI 5-V I2C serial control clock input
SCLK 21 DI 5-V Pulldown Serial audio-data clock (shift clock). SCLK is the serial-audio-port input-data bit clock.
SDA 23 DIO 5-V I2C serial control data interface input/output
SDIN 22 DI 5-V Pulldown Serial audio data input. SDIN supports three discrete (stereo) data formats.
SSTIMER 6 AI Controls ramp time of OUT_x to minimize pop. Leave this pin floating for BD mode. Requires capacitor of 2.2 nF to GND in AD mode. The capacitor determines the ramp time.
STEST 26 DI Factory test pin. Connect directly to DVSS.
VR_ANA 12 P Internally regulated 1.8-V analog supply voltage. This pin must not be used to power external devices.
VR_DIG 18 P Internally regulated 1.8-V digital supply voltage. This pin must not be used to power external devices.
VREG 31 P Digital regulator output. Not to be used for powering external circuitry.
(1) TYPE: A = analog; D = 3.3-V digital; P = power/ground/decoupling; I = input; O = output
(2) All pullups are weak pullups and all pulldowns are weak pulldowns. The pullups and pulldowns are included to assure proper input logic levels if the pins are left unconnected (pullups → logic 1 input; pulldowns → logic 0 input).