ZHCSTI3E June   1986  – October 2023 SN75ALS193

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 Dissipation Rating
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Device Functional Modes
  9. 8 Device and Documentation Support
    1. 8.1 接收文档更新通知
    2. 8.2 支持资源
    3. 8.3 Trademarks
    4. 8.4 静电放电警告
    5. 8.5 术语表
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • N|16
  • D|16
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.5 Electrical Characteristics

over recommended range of common-mode input voltage, supply voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS(1) MIN TYP(2) MAX UNIT
VIT+ Positive-going input threshold voltage 200 mV
VIT- Negative-going input threshold voltage –200(3) mV
Vhys Hysteresis voltage (VIT+ -VIT-) 120 mV
VIK Enable-input clamp voltage VCC = MIN, II = –18 mA –1.5 V
VOH High-level output voltage VCC = MIN, IOH = –400 μA, VID = 200 mV, See Figure 1 2.5 1.6 V
VOL Low-level output voltage VCC = MIN, VID = –200 mV, See Figure 1 IOL = 8 mA 0.45 V
IOL = 16 mA 0.5
IOZ High-impedance-state output current VCC = MAX VO = 2.4 V 20 μA
VO = 0.4 V –20
II Line input current Other input at 0, See (4) VCC = MIN, VI = 15 V 0.7 1.2 mA
VCC = MIN, VI = –15 V –1.0 –1.7
IIH High-level enable-input current VCC = MAX VIH = 2.7 V 20 μA
VIH = MAX 100
IIL Low-level enable-input current VCC = MAX, VIL = 0.4 V –100 μA
Input resistance 12 18 kΩ
IOS Short-circuit output current VCC = MAX, VO = 0, VID = 3 V, See (5) –15 –78 –130 mA
ICC Supply current VCC = MAX, Outputs disabled 22 35 mA
(1) For conditions shown as MIN or MAX, use the appropriate values specified under recommended operating conditions.
(2) All typical values are at VCC = 5 V, TA = 25°C.
(3) The algebraic convention, in which the less positive limit is designated minimum, is used in this data sheet for threshold voltage levels only.
(4) Refer to ANSI Standard EIA/TIA-422-B and EIA/TIA-423-A for exact conditions.
(5) Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.