ZHCSH84A September   2017  – December 2017 SN55HVD233-SP

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     Device Images
      1.      简化原理图
  4. 4 修订历史记录
  5. 5 说明 （续）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Driver Electrical Characteristics
    6. 7.6  Receiver Electrical Characteristics
    7. 7.7  Driver Switching Characteristics
    8. 7.8  Receiver Switching Characteristics
    9. 7.9  Device Switching Characteristics
    10. 7.10 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Modes
      2. 9.3.2 Loopback
      3. 9.3.3 CAN Bus States
      4. 9.3.4 ISO 11898 Compliance of SN55HVD233-SP
        1. 9.3.4.1 Introduction
        2. 9.3.4.2 Differential Signal
          1. 9.3.4.2.1 Common-Mode Signal
        3. 9.3.4.3 Interoperability of 3.3-V CAN in 5-V CAN Systems
      5. 9.3.5 Thermal Shutdown
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Diagnostic Loopback
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Slope Control
        2. 10.2.2.2 Standby
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Bus Loading, Length, and Number of Nodes
      2. 12.1.2 CAN Termination
    2. 12.2 Layout Example
  13. 13器件和文档支持
    1. 13.1 接收文档更新通知
    2. 13.2 社区资源
    3. 13.3 商标
    4. 13.4 静电放电警告
    5. 13.5 Glossary
  14. 14机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.5 Driver Electrical Characteristics

The specifications shown below are valid across temperature range of –55°C to 125°C pre-radiation and 25°C post-radiation. When different, the post-radiation values are shown in a separate row specified by the corresponding RHA level (L = 50 krad).
PARAMETERTEST CONDITIONSSUBGROUP(2)MINTYP(1)MAXUNIT
VO(D) Bus output voltage (dominant) CANH V(D) = 0 V, V(RS) = 0 V, see Figure 12 and Figure 13 [1, 2, 3] 2.4 VCC V
CANL [1, 2, 3] 0.5 1.25
VO Bus output voltage (recessive) CANH V(D) = 3 V, V(RS) = 0 V, see Figure 12 and Figure 13 2.3 V
CANL 2.3
VOD(D) Differential output voltage (dominant) V(D) = 0 V, V(RS) = 0 V, see Figure 12 and Figure 13 [1, 2, 3] 1.5 2 3 V
L 1.4
V(D) = 0 V, V(RS) = 0 V, see Figure 13 and Figure 14 [1, 2, 3] 1.2 2 3
VOD Differential output voltage (recessive) V(D) = 3 V, V(RS) = 0 V, see Figure 12 and Figure 13 [1, 2, 3] –120 12 mV
V(D) = 3 V, V(RS) = 0 V, no load [1, 2, 3] –0.5 0.05 V
VOC(pp) Peak-to-peak common-mode output voltage See Figure 20 1 V
IIH High-level input current D, LBK V(D) = 2 V [1, 2, 3] –30 30 μA
IIL Low-level input current D, LBK V(D) = 0.8 V [1, 2, 3] –30 30 μA
IOS Short-circuit output current V(CANH) = –7 V, CANL open, see Figure 23 [1, 2, 3] –250 mA
V(CANH) = 12 V, CANL open, see Figure 23 [1, 2, 3] 1
V(CANL) = –7 V, CANH open, see Figure 23 [1, 2, 3] –1
V(CANL) = 12 V, CANH open, see Figure 23 [1, 2, 3] 250
CO Output capacitance See receiver input capacitance
IIRS(s) RS input current for standby V(RS) = 0.75 VCC [1, 2, 3] –10 μA
ICC Supply current Standby V(RS) = VCC, V(D) = VCC, V(LBK) = 0 V [1, 2, 3] 200 600 μA
Dominant V(D) = 0 V, no load, V(LBK) = 0 V, RS = 0 V [1, 2, 3] 6 mA
Recessive V(D) = VCC, no load, V(LBK) = 0 V, V(RS) = 0 V [1, 2, 3] 6
(1) All typical values are at 25°C and with a 3.3-V supply.
(2) For subgroup definitions, please see Table 1.