ZHCSHU7J August   2005  – March 2021 PCA9555

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Device Features
      1. 8.3.1 Power-On Reset (POR)
      2. 8.3.2 I/O Port
    4. 8.4 Device Functional Modes
      1. 8.4.1 Interrupt ( INT) Output
        1. 8.4.1.1 Interrupt Errata
          1. 8.4.1.1.1 INT Description
          2. 8.4.1.1.2 System Impact
          3. 8.4.1.1.3 System Workaround
    5. 8.5 Programming
      1. 8.5.1 I2C Interface
      2. 8.5.2 Register Map
        1. 8.5.2.1 Device Address
        2. 8.5.2.2 Control Register And Command Byte
        3. 8.5.2.3 Register Descriptions
        4. 8.5.2.4 Bus Transactions
          1. 8.5.2.4.1 Writes
          2. 8.5.2.4.2 Reads
  9. Application Information Disclaimer
    1. 9.1 Application Information
      1. 9.1.1 Typical Application
        1. 9.1.1.1 Design Requirements
        2. 9.1.1.2 Design Requirements
          1. 9.1.1.2.1 Minimizing ICC When I/O Is Used To Control Led
        3. 9.1.1.3 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Power-On Reset Requirements
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Support Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)
PARAMETERTEST CONDITIONSVCCMINTYP(1)MAXUNIT
VIKInput diode clamp voltageII = –18 mA2.3 V to 5.5 V–1.2V
VPORRPower-on reset voltage, VCC risingVI = VCC or GND, IO = 01.21.5V
VPORFPower-on reset voltage, VCC

falling

VI = VCC or GND, IO = 0

0.75

1

V

VOHP-port high-level output voltage(2)IOH = –8 mA2.3 V1.8V
3 V2.6
4.75 V4.1
IOH = –10 mA2.3 V1.7
3 V2.5
4.75 V4
IOLSDAVOL = 0.4 V2.3 V to 5.5 V3mA
P port(3)VOL = 0.5 V820
VOL = 0.7 V1024
INTVOL = 0.4 V3
IISCL, SDAVI = VCC or GND2.3 V to 5.5 V±1μA
A2–A0±1
IIHP portVI = VCC2.3 V to 5.5 V1μA
IILP portVI = GND2.3 V to 5.5 V–100μA
ICCOperating modeVI = VCC or GND, IO = 0,
I/O = inputs, fSCL = 400 kHz, No load
5.5 V100200μA
3.6 V3075
2.7 V2050
Standby modeLow inputsVI = GND, IO = 0, I/O = inputs,
fSCL = 0 kHz, No load
5.5 V1.11.5mA
3.6 V0.71.3
2.7 V0.51
High inputsVI = VCC, IO = 0, I/O = inputs,
fSCL = 0 kHz, No load
5.5 V2.53.5μA
3.6 V1

1.8

2.7 V0.71.6
ΔICCAdditional current in standby modeOne input at VCC – 0.6 V,
Other inputs at VCC or GND
2.3 V to 5.5 V1.5mA
CISCLVI = VCC or GND2.3 V to 5.5 V38pF
CioSDAVIO = VCC or GND2.3 V to 5.5 V39.5pF
P port3.79.5
All typical values are at nominal supply voltage (2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C.
Each I/O must be externally limited to a maximum of 25 mA, and each octal (P07–P00 and P17–P10) must be limited to a maximum current of 100 mA, for a device total of 200 mA.
The total current sourced by all I/Os must be limited to 160 mA (80 mA for P07–P00 and 80 mA for P17–P10).