ZHCSOY8B September   2021  – February 2022 DRV8311

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 SPI Timing Requirements
    7. 7.7 SPI Secondary Device Mode Timings
    8. 7.8 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Output Stage
      2. 8.3.2  Control Modes
        1. 8.3.2.1 6x PWM Mode (DRV8311S and DRV8311H variants only)
        2. 8.3.2.2 3x PWM Mode (DRV8311S and DRV8311H variants only)
        3. 8.3.2.3 PWM Generation Mode (DRV8311S and DRV8311P Variants)
      3. 8.3.3  Device Interface Modes
        1. 8.3.3.1 Serial Peripheral Interface (SPI)
        2. 8.3.3.2 Hardware Interface
      4. 8.3.4  AVDD Linear Voltage Regulator
      5. 8.3.5  Charge Pump
      6. 8.3.6  Slew Rate Control
      7. 8.3.7  Cross Conduction (Dead Time)
      8. 8.3.8  Propagation Delay
      9. 8.3.9  Pin Diagrams
        1. 8.3.9.1 Logic Level Input Pin (Internal Pulldown)
        2. 8.3.9.2 Logic Level Input Pin (Internal Pullup)
        3. 8.3.9.3 Open Drain Pin
        4. 8.3.9.4 Push Pull Pin
        5. 8.3.9.5 Four Level Input Pin
      10. 8.3.10 Current Sense Amplifiers
        1. 8.3.10.1 Current Sense Amplifier Operation
        2. 8.3.10.2 Current Sense Amplifier Offset Correction
      11. 8.3.11 Protections
        1. 8.3.11.1 VM Supply Undervoltage Lockout (NPOR)
        2. 8.3.11.2 Under Voltage Protections (UVP)
        3. 8.3.11.3 Overcurrent Protection (OCP)
          1. 8.3.11.3.1 OCP Latched Shutdown (OCP_MODE = 010b)
          2. 8.3.11.3.2 OCP Automatic Retry (OCP_MODE = 000b or 001b)
          3. 8.3.11.3.3 OCP Report Only (OCP_MODE = 011b)
          4. 8.3.11.3.4 OCP Disabled (OCP_MODE = 111b)
        4. 8.3.11.4 Thermal Protections
          1. 8.3.11.4.1 Thermal Warning (OTW)
          2. 8.3.11.4.2 Thermal Shutdown (OTSD)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Functional Modes
        1. 8.4.1.1 Sleep Mode
        2. 8.4.1.2 Operating Mode
        3. 8.4.1.3 Fault Reset (CLR_FLT or nSLEEP Reset Pulse)
    5. 8.5 SPI Communication
      1. 8.5.1 Programming
        1. 8.5.1.1 SPI and tSPI Format
  9. DRV8311 Registers
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Three-Phase Brushless-DC Motor Control
        1. 10.2.1.1 Detailed Design Procedure
          1. 10.2.1.1.1 Motor Voltage
        2. 10.2.1.2 Driver Propagation Delay and Dead Time
        3. 10.2.1.3 Delay Compensation
        4. 10.2.1.4 Current Sensing and Output Filtering
        5. 10.2.1.5 Application Curves
    3. 10.3 Three Phase Brushless-DC tSPI Motor Control
      1. 10.3.1 Detailed Design Procedure
    4. 10.4 Alternate Applications
  11. 11Power Supply Recommendations
    1. 11.1 Bulk Capacitance
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
    3. 12.3 Thermal Considerations
      1. 12.3.1 Power Dissipation and Junction Temperature Estimation
  13. 13Device and Documentation Support
    1. 13.1 支持资源
    2. 13.2 Trademarks
    3. 13.3 Electrostatic Discharge Caution
    4. 13.4 术语表
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Protections

The DRV8311 family of devices is protected against VM, VIN_AVDD, AVDD and CP undervoltage, overcurrent and thermal events. Table 8-6 summarizes various faults details.

Table 8-6 Fault Action and Response
FAULTCONDITIONCONFIGURATIONREPORTH-BRIDGELOGICRECOVERY
VM undervoltage
(NPOR)
VVM < VUVLOHi-ZDisabledAutomatic:
VVM > VUVLO_R
CLR_FLT, nSLEEP Reset Pulse (NPOR bit)
VINAVDD undervoltage
(VINAVDD_UV)
VVINAVDD < VVINAVDD_UV nFAULT Hi-Z Active
(SPI disabled)
Configured using UVP_MODE
AVDD undervoltage
(AVDD_UV)
VAVDD < VAVDD_UVnFAULTHi-ZActive
(SPI disabled)
Configured using UVP_MODE
Charge pump undervoltage
(CP_UV)
VCP < VCPUVnFAULTHi-ZActiveConfigured using UVP_MODE
CSAREF undervoltage
(CSAREF_UV)
VCSAREF < VCSAREF_UV CSAREFUV_EN= 1b nFAULT Active
(CSA disabled)
Active Configured using UVP_MODE
CSAREFUV_EN= 0b None Active Active No Action
Overcurrent protection
(OCP)
IPHASE > IOCPOCP_MODE = 000bnFAULTHi-ZActiveAutomatic Retry:
SLOW_TRETRY
OCP_MODE = 001b nFAULT Hi-Z Active Automatic Retry:
FAST_TRETRY
OCP_MODE = 010bnFAULTHi-ZActiveLatched:
CLR_FLT, nSLEEP Reset Pulse
OCP_MODE = 011bnFAULTActiveActiveNo action
OCP_MODE = 111bNoneActiveActiveNo action
SPI fault
(SPI_FLT)
SCLK fault and ADDR faultSPIFLT_MODE = 0bnFAULTActiveActiveAutomatic
SPIFLT_MODE = 1bNoneActiveActiveNo action
Thermal warning
(OTW)
TJ > TOTWOTW_EN = 0bNoneActiveActiveNo action
OTW_EN = 1bnFAULTActiveActiveAutomatic:
TJ < TOTW – THYS
Thermal shutdown
(OTSD)
TJ > TOTSDOTSD_MODE = 00bnFAULTHi-ZActiveAutomatic
SLOW_TRETRY after
TJ < TOTSD – THYS
OTSD_MODE = 01b nFAULT Hi-Z Active Automatic
FAST_TRETRY after
TJ < TOTSD – THYS