ZHCSTD7A December   2021  – November 2023 BQ79631-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 说明（续）
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Measurement System
        1. 8.3.1.1 Voltage Measurement System
          1. 8.3.1.1.1 Main ADC
            1. 8.3.1.1.1.1 VS Voltage Measurements
              1. 8.3.1.1.1.1.1 Analog Front End
              2. 8.3.1.1.1.1.2 VS Channel Measurements
              3. 8.3.1.1.1.1.3 Post-ADC Digital LPF
              4. 8.3.1.1.1.1.4 SRP and SRN Measurements
            2. 8.3.1.1.1.2 Temperature Measurements
              1. 8.3.1.1.1.2.1 DieTemp1 Measurement
              2. 8.3.1.1.1.2.2 GPIOs and TSREF Measurements
            3. 8.3.1.1.1.3 Main ADC Operation Control
              1. 8.3.1.1.1.3.1 Operation Modes and Status
          2. 8.3.1.1.2 AUX ADC
            1. 8.3.1.1.2.1 AUX Voltage Measurements
              1. 8.3.1.1.2.1.1 AUX Analog Front End
              2. 8.3.1.1.2.1.2 AUX Channel Measurements
            2. 8.3.1.1.2.2 AUX Temperature Measurements
              1. 8.3.1.1.2.2.1 DieTemp2 Measurement
              2. 8.3.1.1.2.2.2 AUX GPIO Measurements
            3. 8.3.1.1.2.3 MISC Measurements
            4. 8.3.1.1.2.4 AUX ADC Operation Control
          3. 8.3.1.1.3 Synchronization Between MAIN and AUX ADC Measurements
        2. 8.3.1.2 Current Sense ADC
      2. 8.3.2 OVUV Detection
        1. 8.3.2.1 OVUV Operation Modes
        2. 8.3.2.2 OVUV Control and Status
          1. 8.3.2.2.1 OVUV Control
          2. 8.3.2.2.2 OVUV Status
      3. 8.3.3 Power Supplies
        1. 8.3.3.1 AVAO_REF and AVDD_REF
        2. 8.3.3.2 LDOIN
        3. 8.3.3.3 AVDD
        4. 8.3.3.4 DVDD
        5. 8.3.3.5 CVDD and NEG5V
        6. 8.3.3.6 TSREF
      4. 8.3.4 GPIO Configuration
      5. 8.3.5 Communication, OTP, Diagnostic Control
        1. 8.3.5.1 Communication
          1. 8.3.5.1.1 Serial Interface
            1. 8.3.5.1.1.1 UART Physical Layer
              1. 8.3.5.1.1.1.1 UART Transmitter
              2. 8.3.5.1.1.1.2 UART Receiver
              3. 8.3.5.1.1.1.3 COMM CLEAR
            2. 8.3.5.1.1.2 Command and Response Protocol
              1. 8.3.5.1.1.2.1 Transaction Frame Structure
                1. 8.3.5.1.1.2.1.1 Frame Initialization Byte
                2. 8.3.5.1.1.2.1.2 Device Address Byte
                3. 8.3.5.1.1.2.1.3 Register Address Bytes
                4. 8.3.5.1.1.2.1.4 Data Bytes
                5. 8.3.5.1.1.2.1.5 CRC Bytes
                6. 8.3.5.1.1.2.1.6 Calculating Frame CRC Value
                7. 8.3.5.1.1.2.1.7 Verifying Frame CRC
              2. 8.3.5.1.1.2.2 Transaction Frame Examples
                1. 8.3.5.1.1.2.2.1 Single Device Read/Write
                2. 8.3.5.1.1.2.2.2 Stack Read/Write
                3. 8.3.5.1.1.2.2.3 Broadcast Read/Write
                4. 8.3.5.1.1.2.2.4 Broadcast Write Reverse Direction
          2. 8.3.5.1.2 Daisy-Chain Interface
            1. 8.3.5.1.2.1 Daisy-Chain Transmitter and Receiver Functionality
            2. 8.3.5.1.2.2 Daisy-Chain Protocol
          3. 8.3.5.1.3 Start Communication
            1. 8.3.5.1.3.1 Identify Base and Stack
            2. 8.3.5.1.3.2 Auto-Addressing
              1. 8.3.5.1.3.2.1 Setting Up the Device Addresses
              2. 8.3.5.1.3.2.2 Setting Up COMM_CTRL[STACK_DEV] and [TOP_STACK]
              3. 8.3.5.1.3.2.3 Storing Device Address to OTP
            3. 8.3.5.1.3.3 Synchronize Daisy-Chain DLL
            4. 8.3.5.1.3.4 Ring Communication
          4. 8.3.5.1.4 Communication Timeout
            1. 8.3.5.1.4.1 Short Communication Timeout
            2. 8.3.5.1.4.2 Long Communication Timeout
          5. 8.3.5.1.5 Communication Debug Mode
          6. 8.3.5.1.6 Multidrop Configuration
          7. 8.3.5.1.7 SPI Master
          8. 8.3.5.1.8 SPI Loopback
        2. 8.3.5.2 Fault Handling
          1. 8.3.5.2.1 Fault Status Hierarchy
            1. 8.3.5.2.1.1 Debug Registers
          2. 8.3.5.2.2 Fault Masking and Reset
            1. 8.3.5.2.2.1 Fault Masking
            2. 8.3.5.2.2.2 Fault Reset
          3. 8.3.5.2.3 Fault Signaling
            1. 8.3.5.2.3.1 Fault Status Transmitting in ACTIVE Mode
            2. 8.3.5.2.3.2 Fault Status Transmitting in SLEEP Mode
            3. 8.3.5.2.3.3 Heartbeat and Fault Tone
        3. 8.3.5.3 Nonvolatile Memory
          1. 8.3.5.3.1 OTP Page Status
          2. 8.3.5.3.2 OTP Programming
        4. 8.3.5.4 Diagnostic Control/Status
          1. 8.3.5.4.1 Power Supplies Check
            1. 8.3.5.4.1.1 Power Supply Diagnostic Check
            2. 8.3.5.4.1.2 Power Supply BIST
          2. 8.3.5.4.2 Thermal Shutdown and Warning Check
            1. 8.3.5.4.2.1 Thermal Shutdown
            2. 8.3.5.4.2.2 Thermal Warning
          3. 8.3.5.4.3 Oscillators Watchdog
          4. 8.3.5.4.4 OTP Error Check
            1. 8.3.5.4.4.1 OTP CRC Test and Faults
            2. 8.3.5.4.4.2 OTP Margin Read
            3. 8.3.5.4.4.3 Error Check and Correct (ECC) OTP
          5. 8.3.5.4.5 OVUV Detection Check
            1. 8.3.5.4.5.1 Parity Check
            2. 8.3.5.4.5.2 OVUV DAC Check
            3. 8.3.5.4.5.3 OVUV Protector BIST
          6. 8.3.5.4.6 Diagnostic Through ADC Comparison
            1. 8.3.5.4.6.1 VS Voltage Measurement Check
            2. 8.3.5.4.6.2 Temperature Measurement Check
            3. 8.3.5.4.6.3 VS and AUX Open Wire Check
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power Modes
        1. 8.4.1.1 SHUTDOWN Mode
          1. 8.4.1.1.1 Exit SHUTDOWN Mode
          2. 8.4.1.1.2 Enter SHUTDOWN Mode
        2. 8.4.1.2 SLEEP Mode
          1. 8.4.1.2.1 Exit SLEEP Mode
          2. 8.4.1.2.2 Enter SLEEP Mode
        3. 8.4.1.3 ACTIVE Mode
          1. 8.4.1.3.1 Exit ACTIVE Mode
          2. 8.4.1.3.2 Enter ACTIVE Mode From SHUTDOWN Mode
          3. 8.4.1.3.3 Enter ACTIVE Mode From SLEEP Mode
      2. 8.4.2 Device Reset
      3. 8.4.3 Ping and Tone
        1. 8.4.3.1 Ping
        2. 8.4.3.2 Tone
        3. 8.4.3.3 Ping and Tone Propagation
    5. 8.5 Register Maps
      1. 8.5.1 OTP Shadow Register Summary
      2. 8.5.2 Read/Write Register Summary
      3. 8.5.3 Read-Only Register Summary
      4. 8.5.4 Register Field Descriptions
        1. 8.5.4.1  Device Addressing Setup
          1. 8.5.4.1.1 DIR0_ADDR_OTP
          2. 8.5.4.1.2 DIR1_ADDR_OTP
          3. 8.5.4.1.3 CUST_MISC1 through CUST_MISC8
          4. 8.5.4.1.4 DIR0_ADDR
          5. 8.5.4.1.5 DIR1_ADDR
        2. 8.5.4.2  Device ID and Scratch Pad
          1. 8.5.4.2.1 PARTID
          2. 8.5.4.2.2 DEV_REVID
          3. 8.5.4.2.3 DIE_ID1 through DIE_ID9
        3. 8.5.4.3  General Configuration and Control
          1. 8.5.4.3.1  DEV_CONF
          2. 8.5.4.3.2  PWR_TRANSIT_CONF
          3. 8.5.4.3.3  COMM_TIMEOUT_CONF
          4. 8.5.4.3.4  TX_HOLD_OFF
          5. 8.5.4.3.5  STACK_RESPONSE
          6. 8.5.4.3.6  COMM_CTRL
          7. 8.5.4.3.7  CONTROL1
          8. 8.5.4.3.8  CONTROL2
          9. 8.5.4.3.9  CUST_CRC_HI
          10. 8.5.4.3.10 CUST_CRC_LO
          11. 8.5.4.3.11 CUST_CRC_RSLT_HI
          12. 8.5.4.3.12 CUST_CRC_RSLT_LO
        4. 8.5.4.4  Operation Status
          1. 8.5.4.4.1 DIAG_STAT
          2. 8.5.4.4.2 ADC_STAT1
          3. 8.5.4.4.3 ADC_STAT2
          4. 8.5.4.4.4 GPIO_STAT
          5. 8.5.4.4.5 DEV_STAT
        5. 8.5.4.5  ADC Configuration and Control
          1. 8.5.4.5.1  ADC_CONF1
          2. 8.5.4.5.2  ADC_CONF2
          3. 8.5.4.5.3  MAIN_ADC_CAL1
          4. 8.5.4.5.4  MAIN_ADC_CAL2
          5. 8.5.4.5.5  AUX_ADC_CAL1
          6. 8.5.4.5.6  AUX_ADC_CAL2
          7. 8.5.4.5.7  CS_ADC_CAL1
          8. 8.5.4.5.8  CS_ADC_CAL2
          9. 8.5.4.5.9  ADC_CTRL1
          10. 8.5.4.5.10 ADC_CTRL2
          11. 8.5.4.5.11 ADC_CTRL3
        6. 8.5.4.6  ADC Measurement Results
          1. 8.5.4.6.1  VS16_HI/LO
          2. 8.5.4.6.2  VS15_HI/LO
          3. 8.5.4.6.3  VS14_HI/LO
          4. 8.5.4.6.4  VS13_HI/LO
          5. 8.5.4.6.5  VS12_HI/LO
          6. 8.5.4.6.6  VS11_HI/LO
          7. 8.5.4.6.7  VS10_HI/LO
          8. 8.5.4.6.8  VS9_HI/LO
          9. 8.5.4.6.9  VS8_HI/LO
          10. 8.5.4.6.10 VS7_HI/LO
          11. 8.5.4.6.11 VS6_HI/LO
          12. 8.5.4.6.12 VS5_HI/LO
          13. 8.5.4.6.13 VS4_HI/LO
          14. 8.5.4.6.14 VS3_HI/LO
          15. 8.5.4.6.15 VS2_HI/LO
          16. 8.5.4.6.16 VS1_HI/LO
          17. 8.5.4.6.17 CSAUX_HI/LO
          18. 8.5.4.6.18 TSREF_HI/LO
          19. 8.5.4.6.19 GPIO1_HI/LO
          20. 8.5.4.6.20 GPIO2_HI/LO
          21. 8.5.4.6.21 GPIO3_HI/LO
          22. 8.5.4.6.22 GPIO4_HI/LO
          23. 8.5.4.6.23 GPIO5_HI/LO
          24. 8.5.4.6.24 GPIO6_HI/LO
          25. 8.5.4.6.25 GPIO7_HI/LO
          26. 8.5.4.6.26 GPIO8_HI/LO
          27. 8.5.4.6.27 DIETEMP1_HI/LO
          28. 8.5.4.6.28 DIETEMP2_HI/LO
          29. 8.5.4.6.29 AUX_IN_HI/LO
          30. 8.5.4.6.30 AUX_GPIO_HI/LO
          31. 8.5.4.6.31 AUX_PWR_HI/LO
          32. 8.5.4.6.32 AUX_REFL_HI/LO
          33. 8.5.4.6.33 AUX_VBG2_HI/LO
          34. 8.5.4.6.34 AUX_AVAO_REF_HI/LO
          35. 8.5.4.6.35 AUX_AVDD_REF_HI/LO
          36. 8.5.4.6.36 AUX_OV_DAC_HI/LO
          37. 8.5.4.6.37 AUX_UV_DAC_HI/LO
          38. 8.5.4.6.38 AUX_VCM1_HI/LO
          39. 8.5.4.6.39 REFH_HI/LO
          40. 8.5.4.6.40 DIAG_MAIN_HI/LO
          41. 8.5.4.6.41 DIAG_AUX_HI/LO
          42. 8.5.4.6.42 CURRENT_HI/MID/LO
        7. 8.5.4.7  Protector Configuration and Control
          1. 8.5.4.7.1 OV_THRESH
          2. 8.5.4.7.2 UV_THRESH
          3. 8.5.4.7.3 UV_DISABLE1
          4. 8.5.4.7.4 UV_DISABLE2
          5. 8.5.4.7.5 OVUV_CTRL
        8. 8.5.4.8  GPIO Configuration
          1. 8.5.4.8.1 GPIO_CONF1
          2. 8.5.4.8.2 GPIO_CONF2
          3. 8.5.4.8.3 GPIO_CONF3
          4. 8.5.4.8.4 GPIO_CONF4
        9. 8.5.4.9  SPI Master
          1. 8.5.4.9.1 SPI_CONF
          2. 8.5.4.9.2 SPI_EXE
          3. 8.5.4.9.3 SPI_TX3, SPI_TX2, and SPI_TX1
          4. 8.5.4.9.4 SPI_RX3, SPI_RX2, and SPI_RX1
        10. 8.5.4.10 Diagnostic Control
          1. 8.5.4.10.1 DIAG_OTP_CTRL
          2. 8.5.4.10.2 DIAG_COMM_CTRL
          3. 8.5.4.10.3 DIAG_PWR_CTRL
          4. 8.5.4.10.4 DIAG_COMP_CTRL1
          5. 8.5.4.10.5 DIAG_COMP_CTRL2
          6. 8.5.4.10.6 DIAG_COMP_CTRL3
          7. 8.5.4.10.7 DIAG_COMP_CTRL4
          8. 8.5.4.10.8 DIAG_PROT_CTRL
        11. 8.5.4.11 Fault Configuration and Reset
          1. 8.5.4.11.1 FAULT_MSK1
          2. 8.5.4.11.2 FAULT_MSK2
          3. 8.5.4.11.3 FAULT_RST1
          4. 8.5.4.11.4 FAULT_RST2
        12. 8.5.4.12 Fault Status
          1. 8.5.4.12.1  FAULT_SUMMARY
          2. 8.5.4.12.2  FAULT_COMM1
          3. 8.5.4.12.3  FAULT_COMM2
          4. 8.5.4.12.4  FAULT_COMM3
          5. 8.5.4.12.5  FAULT_OTP
          6. 8.5.4.12.6  FAULT_SYS
          7. 8.5.4.12.7  FAULT_PROT1
          8. 8.5.4.12.8  FAULT_PROT2
          9. 8.5.4.12.9  FAULT_OV1
          10. 8.5.4.12.10 FAULT_OV2
          11. 8.5.4.12.11 FAULT_UV1
          12. 8.5.4.12.12 FAULT_UV2
          13. 8.5.4.12.13 FAULT_COMP_GPIO
          14. 8.5.4.12.14 FAULT_COMP_VSAUX1
          15. 8.5.4.12.15 FAULT_COMP_VSAUX2
          16. 8.5.4.12.16 FAULT_COMP_VSOW1
          17. 8.5.4.12.17 FAULT_COMP_VSOW2
          18. 8.5.4.12.18 FAULT_COMP_AUXOW1
          19. 8.5.4.12.19 FAULT_COMP_AUXOW2
          20. 8.5.4.12.20 FAULT_COMP_MISC
          21. 8.5.4.12.21 FAULT_PWR1
          22. 8.5.4.12.22 FAULT_PWR2
          23. 8.5.4.12.23 FAULT_PWR3
        13. 8.5.4.13 Debug Control and Status
          1. 8.5.4.13.1  DEBUG_CTRL_UNLOCK
          2. 8.5.4.13.2  DEBUG_COMM_CTRL1
          3. 8.5.4.13.3  DEBUG_COMM_CTRL2
          4. 8.5.4.13.4  DEBUG_COMM_STAT
          5. 8.5.4.13.5  DEBUG_UART_RC
          6. 8.5.4.13.6  DEBUG_UART_RR_TR
          7. 8.5.4.13.7  DEBUG_COMH_BIT
          8. 8.5.4.13.8  DEBUG_COMH_RC
          9. 8.5.4.13.9  DEBUG_COMH_RR_TR
          10. 8.5.4.13.10 DEBUG_COML_BIT
          11. 8.5.4.13.11 DEBUG_COML_RC
          12. 8.5.4.13.12 DEBUG_COML_RR_TR
          13. 8.5.4.13.13 DEBUG_UART_DISCARD
          14. 8.5.4.13.14 DEBUG_COMH_DISCARD
          15. 8.5.4.13.15 DEBUG_COML_DISCARD
          16. 8.5.4.13.16 DEBUG_UART_VALID_HI/LO
          17. 8.5.4.13.17 DEBUG_COMH_VALID_HI/LO
          18. 8.5.4.13.18 DEBUG_COML_VALID_HI/LO
          19. 8.5.4.13.19 DEBUG_OTP_SEC_BLK
          20. 8.5.4.13.20 DEBUG_OTP_DED_BLK
        14. 8.5.4.14 OTP Programming Control and Status
          1. 8.5.4.14.1 OTP_PROG_UNLOCK1A through OTP_PROG_UNLOCK1D
          2. 8.5.4.14.2 OTP_PROG_UNLOCK2A through OTP_PROG_UNLOCK2D
          3. 8.5.4.14.3 OTP_PROG_CTRL
          4. 8.5.4.14.4 OTP_ECC_TEST
          5. 8.5.4.14.5 OTP_ECC_DATAIN1 through OTP_ECC_DATAIN9
          6. 8.5.4.14.6 OTP_ECC_DATAOUT1 through OTP_ECC_DATAOUT9
          7. 8.5.4.14.7 OTP_PROG_STAT
          8. 8.5.4.14.8 OTP_CUST1_STAT
          9. 8.5.4.14.9 OTP_CUST2_STAT
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Base Device Application Circuit
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1  PACK+ and FUSE Measurement
          2. 9.2.1.2.2  Insulation Measurement
          3. 9.2.1.2.3  LINK+/- Measurement
          4. 9.2.1.2.4  CHARGE+/– Measurement
          5. 9.2.1.2.5  Overcurrent Detection Scheme Using OVUV Comparators
          6. 9.2.1.2.6  Unused Pins
          7. 9.2.1.2.7  Current Sense Input
          8. 9.2.1.2.8  VPWR and External NPN
          9. 9.2.1.2.9  Power Supplies, Reference Input
          10. 9.2.1.2.10 GPIO For Thermistor Inputs
          11. 9.2.1.2.11 UART, NFAULT
          12. 9.2.1.2.12 Daisy-Chain Isolation
            1. 9.2.1.2.12.1 Devices Connected on the Same PCB
            2. 9.2.1.2.12.2 Devices Connected on Different PCBs
        3. 9.2.1.3 Application Curve
      2. 9.2.2 Daisy Device Application Circuit
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Ground Planes
      2. 11.1.2 Bypass Capacitors for Power Supplies and Reference
      3. 11.1.3 Voltage Sensing
      4. 11.1.4 Daisy-Chain Communication
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 第三方产品免责声明
    2. 12.2 接收文档更新通知
    3. 12.3 支持资源
    4. 12.4 Trademarks
    5. 12.5 静电放电警告
    6. 12.6 术语表
  14. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.5.2 Read/Write Register Summary

Register NameAddr HexRW TypeReset ValueData
Bit7Bit6Bit5Bit4Bit3Bit2Bit1Bit0
OTP_PROG_UNLOCK1A through OTP_PROG_UNLOCK1D300RW0x00CODE[7:0]
301RW0x00CODE[7:0]
302RW0x00CODE[7:0]
303RW0x00CODE[7:0]
DIR0_ADDR306RW0x00RSVDADDRESS[5:0]
DIR1_ADDR307RW0x00RSVDADDRESS[5:0]
COMM_CTRL308RW0x00RSVDSTACK_ DEVTOP_ STACK
CONTROL1309RW0x00DIR_SELSEND_ SHUT DOWNSEND_ WAKESEND_ SLPTO ACTGOTO_ SHUT DOWNGOTO_ SLEEPSOFT_ RESETADDR_ WR
CONTROL230ARW0x00RSVDSEND_ HW_ RESETTSREF _EN
OTP_PROG_CTRL30BRW0x00RSVDPAGE SELPROG _GO
ADC_CTRL130DRW0x00RSVDCS_DR[1:0]LPF_CSAUX _ENLPF_ VS_ ENCS_MAIN_GOMAIN_MODE[1:0]
ADC_CTRL230ERW0x00RSVD MAINAUXCS_AFE_DISAUX_IN_ALIGNAUX_IN_SEL[4:0]
ADC_CTRL330FRW0x00RSVDAUX_GPIO_SEL[3:0]AUX_GOAUX_MODE[1:0]
REG_INT_RSVD310RW0x00INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
REG_INT_RSVD 318 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
319 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
31A RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
31B RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
31C RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
31D RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
31E RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
31F RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
320 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
321 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
322 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
323 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
324 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
325 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
326 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
327 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
REG_INT_RSVD 328 RW 0x3F INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
329 RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
32A RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
32B RW 0x0F INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
OVUV_CTRL32CRW0x00RSVDOVUV_LOCK[3:0]OVUV _GOOVUV_MODE[1:0]
REG_INT_RSVD 32D RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
REG_INT_RSVD 32E RW 0x00 INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
REG_INT_RSVD32FRW0x00INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
REG_INT_RSVD330RW0x00INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
FAULT_RST1331RW0x00RST_ PROTRSVDRSVDRST_UVRST_OVRST_ COMPRST_SYSRST_ PWR
FAULT_RST2332RW0x00RSVDRST_OTP _CRCRST_OTP _DATARST_ COMM3_ FCOMMRST_ COMM3_ FTONERST_ COMM3_ HBRST_ COMM2RST_ COMM1
DIAG_OTP_CTRL335RW0x00RSVDFLIP_ FACT_ CRCMARGIN_MODE[2:0]MARGIN _GO
DIAG_COMM_CTRL336RW0x00RSVDSPI_ LOOP BACKFLIP_TR _CRC
DIAG_PWR_CTRL337RW0x00RSVDBIST_ NO_RSTPWR_ BIST_GO
REG_INT_RSVD338RW0x00INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
REG_INT_RSVD339RW0x00INTERNAL USE. DO NOT WRITE TO THIS ADDRESS
DIAG_COMP_CTRL133ARW0x00VSAUX_THR[4:0]RSVD
DIAG_COMP_CTRL233BRW0x00RSVDGPIO_THR[2:0]OW_THR[3:0]
DIAG_COMP_CTRL333CRW0x00RSVDRSVDOW_SNK[1:0]COMP_ADC_SEL[2:0]COMP_ ADC_GO
DIAG_COMP_CTRL433DRW0x00RSVDCOMP_ FAULT _INJLPF_ FAULT _INJ
DIAG_PROT_CTRL33ERW0x00RSVDPROT_ BIST_ NO_RST
OTP_ECC_DATAIN1 through OTP_ECC_DATAIN9343RW0x00DATA[7:0]
344RW0x00DATA[7:0]
345RW0x00DATA[7:0]
346RW0x00DATA[7:0]
347RW0x00DATA[7:0]
348RW0x00DATA[7:0]
349RW0x00DATA[7:0]
34ARW0x00DATA[7:0]
34BRW0x00DATA[7:0]
OTP_ECC_TEST34CRW0x00RSVDDED_ SECMANUAL _AUTOENC_ DECENABLE
SPI_CONF34DRW0x00RSVDCPOLCPHANUMBIT[4:0]
SPI_TX3, SPI_TX2, and SPI_TX134ERW0x00DATA[7:0]
34FRW0x00DATA[7:0]
350RW0x00DATA[7:0]
SPI_EXE351RW0x02RSVDSS_CTRLSPI_GO
OTP_PROG_UNLOCK2A through OTP_PROG_UNLOCK2D352RW0x00CODE[7:0]
353RW0x00CODE[7:0]
354RW0x00CODE[7:0]
355RW0x00CODE[7:0]
DEBUG_CTRL_UNLOCK 700 RW 0x00 CODE[7:0]
DEBUG_COMM_CTRL1 701 RW 0x04 RSVD UART_ BAUD UART_ MIRROR _EN UART_ TX_EN USER_ UART_ EN USER_ DAISY _EN
DEBUG_COMM_CTRL2 702 RW 0x0F RSVD COML_ TX_EN COML_ RX_EN COMH_ TX_EN COMH_ RX_EN