5 Revision History
Changes from February 11, 2020 to August 30, 2020 (from Revision * (February 2020) to Revision A (August 2020))
- 通篇:更新了整个文档中的表格、图和交叉参考的编号格式。Go
- 通篇:添加/更新了仅在 AWR2243P 上支持的级联功能Go
- 通篇:添加/更新了“以符合功能安全标准为目标”信息Go
- 通篇:将 AWR2243 产品状态从“预告信息 (AI)”更新为“量产数据 (PD)”Go
- (器件信息):更新/更改了表以反映量产器件型号。Go
- (功能方框图):更新/更改了脚注以反映 AWR2243、AWR2243P 和 AWR1843Go
-
Table 6-1 (Device Features Comparison): Added AWR2243P device-specific
features to table and updated associated footnotesGo
-
Table 6-1: Updated/Changed Max sampling rate FUNCTION to separate complex 1x and 2x
casesGo
-
Table 7-1 (Signal Descriptions): Updated/Changed the DEFAULT PULL STATUS and DESCRIPTION for
NRESET (P12)Go
-
Table 7-1: Added recommended connectivity for GPIO[0] (N4) during DebugGo
-
Section 8.1
(Absolute Maximum Ratings): Updated/Changed the MAX value for Operating junction
temperature range from "125" to "140", as Automotive.Go
-
Section 8.3 (Power-On
Hours (POH)): Updated/Changed table to reflect automotive junction temp POH
percentages.Go
-
Section 8.4 (Recommended Operating
Conditions): Added TJ, Operating junction temperature rangeGo
-
Section 8.6 (Power Consumption Summary): Added missing table reference to the
paragraphGo
-
Table 8-3 (Maximum Current Ratings at Power Terminals): Added the current consumption VDDIN MAX
value of "850 mA" for AWR2243Go
-
Section 8.7 (RF Specification): Updated/Changed the MAX values for IF bandwidth and A2D sampling
rate for both "(real/complex 2x)" and "(complex 1x)" to reflect the AWR2243P and AWR2243
devices.Go
-
Section 8.7: Added 20GHz SYNC OUT output level max value of 10 dBm and 20GHz SYNC IN input level
max value of 7 dBm with associated footnote. Go
-
Section 8.7: Corrected the phase noise measurement conditions to reflect VCO1 value
only.Go
-
Section 8.7: Updated/Changed the 1-dB compression point TYP value from "-8" to "-9" dBm, and
updated the corresponding footnote frequency from "50" to "10" kHzGo
-
Figure 8-1
(Noise Figure, In-band P1dB vs Receiver Gain): Updated figureGo
-
Section 8.8
(Thermal Resistance Characteristics): Deleted the 125°C
junction temperature reference from footnote #GUID-968ED596-BC99-45AD-92FF-E60FC4A0F954/THERM_CHAR_AUTO_FTN3.Go
-
Figure 8-2 (Device Wake-Up Sequence): Removed associated MCU_CLK_OUT footnote from
imageGo
-
Section 8.9.3.1
(Clock Specifications): Added the External Clock Mode Specifications
table
Go
-
Section 8.9.4
(Multibuffered / Standard Serial Peripheral Interface (MibSPI)): Updated
sectionGo
-
Figure 8-6 (SPI Communication): Updated figure.Go
-
Section 10
(Monitoring and Diagnostic Mechanisms): Added new sectionGo
-
(Monitoring and Diagnostic Mechanisms) : Added a new note on
Functional Safety related collateralGo
-
Figure 11-1 (Short-, Medium-, and Long-Range Radar): Updated figureGo
-
Section 11.3 (Imaging Radar using Cascade Configuration): Updated figureGo
-
(Reference Schematic): Updated/Changed the VBGAP decoupling
capacitor value from "0.22 uF" to "47 nF"Go
-
Figure 12-1 (Device Nomenclature): Updated/Changed figureGo
Changes from September 1, 2020 to December 5, 2021 (from Revision A (September 2020) to Revision B (December 2021))
-
通篇:进行了更新,以反映功能安全合规性及相关认证资料Go
-
通篇:将“A2D”替换为“ADC”;将“主子系统”和“主 R4F”更改为“主要子系统”和“主要 R4F”;在主/从术语方面改用了更具包容性的措辞。Go
-
(特性):提及了毫米波传感器的额定工作温度范围Go
-
(应用):为“自动紧急刹车”添加了应用网络链接Go
-
(Device Feature Comparison): Removed a row on
Functional-Safety compliance and instead added a table-note for this; Also added
a table-note for LVDS operationGo
-
(Device Feature Comparison): Updated GPADC row to reflect
applicability for AWR2243 and AWR2243P devicesGo
-
(Signal Descriptions): Updated/modified GPADC pin description, and
CLKP/CLKM decriptions for Reference OscillatorGo
-
(Signal Descriptions): Added a table-note for QSPI Interface
usageGo
-
(Maximum Current Ratings at Power Terminals) : Added a table-note for 3.3V Power
railGo
-
(RF Specification) : Updated the link for mmWave Radar Interface
Control document in the footnotes.Go
- (Frame Trigger Timing) : Updated the maximum pulse width to 4us in
the table. Go
-
(Clock Specifications): Updated/Changed "Crystal
Electrical Characteristics (Oscillator Mode)" to reflect correct device
operating temperature range; Revised frequency tolerance specs in "External
Clock Mode Specifications" tableGo
-
(Switching Characteristics for Output Timing versus Load
Capacitance): Updated/Modified the table to remove Slew Rate = 1
condition; removed a footnoteGo
- (Other Subsytems) : Added a new chapter for ADC channels for user
service application.Go
-
(GPADC) :Additional chapter appended to describe ADC Channels
for User ApplicationGo
-
(Monitoring and Diagnostic Mechanisms) : Added a new note on
Functional Safety related collateralGo
-
(Reference Schematic) : Added weblinks to AWR2243 EVM
documentation collateralGo
-
(Device Nomenclature): Updated/Changed figure to reflect Functional
Safety ComplianceGo
Changes from December 6, 2021 to June 30, 2022 (from Revision B (December 2021) to Revision C (June 2022))
-
(器件信息):更新/更改了表以删除不受支持的量产器件型号。Go
-
(功能方框图):更新/更改了脚注以反映 AWR2243 中的级联支持,并删除了不受支持的器件型号提及。Go
-
(Device Feature Comparison): Removed unsupported devices from
the table and updated the feature set for AWR2243 (Including Max IF Bandwidth,
Sampling rates and cascade support)Go
-
(Signal Descriptions): Added a table-note for QSPI Interface
usageGo
-
(Maximum Current Ratings at Power Terminals) : Removed data for unsupported part
variant AWR2243PGo
-
(RF Specification): Removed data for unsupported part variant
AWR2243P and updated feature set for AWR2243 (Including Max IF Bandwidth, Sampling rates
and cascade support)Go