ZHCSAM3B December 2012 – April 2022 ADS54T01
PRODUCTION DATA
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 0 | 3/4 Wire SPI | Dec Fil/ Burst | 0 | High/ Low Pass | 0 | 0 | 0 | 0 | 0 | 0 | Burst rate | 0 | 0 | Auto Trigger | 0 | 0 |
| D15 | 3/4 Wire SPI Default 0 | Enables 4-bit serial interface when set |
| 0 | 3-wire SPI is used with SDIO pin operating as bidirectional I/O port | |
| 1 | 4-wire SPI is used with SDIO pin operating as data input and SDO pin as data output port. | |
| D14 | DecFil/ Burst Default 0 | 2x decimation filter (Receive Mode) is enabled when bit is set |
| 0 | Burst mode enable | |
| 1 | 2x decimation filter enabled | |
| D12 | High/Low Pass Default 0 | (Decimation filter must be enabled first: set bit D14) |
| 0 | Low Pass | |
| 1 | High Pass | |
| D5 | Burst Rate Default 0 | Low resolution output data rate in burst mode |
| 0 | Low resolution (9-bit) full output rate | |
| 1 | Decimated low resolution output (4x decimation, 11-bit resolution) | |
| D2 | Auto Trigger Default 0 | Enables auto trigger mode in burst mode without the need to control the trigger pin. |
| 0 | Manual trigger mode using the external trigger input pin | |
| 1 | Auto trigger mode enabled | |
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 1 | Corr EN | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | Data Format | 0 | HP Mode1 | 0 |
| D15 | Corr EN (should be enabled for maximum performance) Default 0 | |
| 0 | auto gain correction disabled | |
| 1 | auto gain correction enabled | |
| D3 | Data Format Default 0 | |
| 0 | Two's complement | |
| 1 | Offset Binary | |
| D1 | HP Mode 1 Default 0 | |
| 1 | Must be set to 1 for optimum performance | |
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 2 | 0 | 1 | 1 | 0 | 0 | Over-range threshold | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
| D14 | Read back 1. | |||
| D13 | Read back 1. | |||
| D10-D7 | Over-range threshold | The over-range detection is triggered 12 output clock cycles after the overload condition occurs. The threshold at which the OVR is triggered = 1.0V x [decimal value of <Over-range threshold>]/16. After power up or reset, the default value is 15 (decimal) which corresponds to a OVR threshold of 0.56dB below fullscale (20*log(15/16)). This OVR threshold is applicable to both channels. | ||
| Default 1111 | ||||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 3 | 0 | DC Offset Coff | 0 | 0 | 1 | 0 | 1 | 1 | 0 | 0 | 0 | 1 | 1 | 0 | 0 | 0 |
| D14 | DC Offset Corr Default 1 | Starts DC offset correction loop | |
| 0 | Starts offset correction loop | ||
| 1 | DC offset correction loop is cleared | ||
| D11, 9, 8, 4, 3 | Must be set to 1 for maximum performance Default 1 | ||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| E | Sync Select | 0 | 0 | |||||||||||||
| D15-D2 | Sync Select Default 1010 1010 1010 10 | Sync selection for the clock generator block (also need to see address 0x0F) | |
| 0000 0000 0000 00 | Sync is disabled | ||
| 0101 0101 0101 01 | Sync is set to one shot (one time synchronization only) | ||
| 1010 1010 1010 10 | Sync is derived from SYNC input pins | ||
| 1111 1111 1111 11 | not supported | ||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| F | Sync Select | 0 | 0 | 0 | 0 | 0 | VREF Sel | 0 | 0 | 0 | 0 | |||||
| D15-D12 | Sync Select Default 1010 1010 1010 10 | Sync selection for the clock generator block | |
| 0000 | Sync is disabled | ||
| 0101 | Sync is set to one shot (one time synchronization only) | ||
| 1010 | Sync is derived from SYNC input pins | ||
| 1111 | not supported | ||
| D6-D4 | VREF SEL Default 000 | Internal voltage reference selection | |
| 000 | 1.0 V | ||
| 001 | 1.25 V | ||
| 010 | 0.9 V | ||
| 011 | 0.8 V | ||
| 100 | 1.15 V | ||
| Others | external reference | ||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 1A | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 1 | 0 | 0 | 0 | 1 | 1 | 0 | 0 | 0 |
| D14, 11, 9, 8, 4, 3 | Must be set to 1 for maximum performance Default 1 | ||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 2B | 0 | 0 | 0 | 0 | 0 | 0 | 0 | Temp Sensor | ||||||||
| D8-D0 | Temp Sensor | Internal temperature sensor value – read only |
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 2C | Reset | |||||||||||||||
| D15-D0 | Reset Default 0000 | This is a software reset to reset all SPI registers to their default value. Self clears to 0. | |
| 1101001011110000 | Perform software reset | ||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 34 | 0 | 0 | Burst Mode N | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
| D13-D10 | Burst Mode N Default 0000 | This is the parameter that sets the amount of high resolution samples in burst mode | |
| 0000 | N = 10 | ||
| 0001 | N = 11 | ||
| ... | ... | ||
| 1111 | N = 25 | ||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 37 | Sleep Modes | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||||
| D15-D14 | Sleep Modes Default 00 | Sleep mode selection which is controlled by the ENABLE pin. Sleep modes are active when ENABLE pin goes low. | |
| 000000 | Complete shut down | Wake up time 2.5 ms | |
| 100000 | Standby mode | Wake up time 100 µs | |
| 110000 | Deep sleep mode | Wake up time 20 µs | |
| 110101 | Light sleep mode | Wake up time 2 µs | |
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 38 | HP Mode 2 | LP Mode | TEMP EN | FUSE Bias EN | SYNC EN | TRIG EN | 1 | 1 | 1 | 1 | ||||||
| D15-D9 | HP Mode 2 Default 111111111 | ||
| 1 | Set to 1 for normal operation | ||
| D8 | LP Mode Default 1 | Low power mode | |
| 0 | Set to 0 to turn off unused output buffers | ||
| D7 | TEMP EN Default 1 | Temperature sensor enable | |
| 1 | Set to 1 to enable the temperature sensor | ||
| D6 | FUSE BIAS EN Default 1 | Enables internal bias voltages. Can be disabled after power up for power savings. | |
| 0 | Internal fuse bias powered down | ||
| 1 | Internal fuse bias enabled | ||
| D5 | SYNC EN Default 1 | Enables the SYNC input buffer. | |
| 0 | SYNC input buffer disabled | ||
| 1 | SYNC input bffer enabled | ||
| D4 | TRIG EN Default 1 | Enables the TRIGGER input buffer. | |
| 0 | TRIGGER input buffer disabled | ||
| 1 | TRIGGER input bffer enabled | ||
| D3-D0 | Read back 1 | ||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 3A | LVDS Current Strength | LVDS SW | Internal LVDS Termination | 0 | 0 | 0 | 0 | DACLK EN | 0 | 0 | OVRA EN | 0 | ||||
| D15-D13 | LVDS Current Strength Default 000 | LVDS output current strength. | |||
| 000 | 2 mA | 100 | 3 mA | ||
| 001 | 2.25 mA | 101 | 3.25 mA | ||
| 010 | 2.5 mA | 110 | 3.5 mA | ||
| 011 | 2.75 mA | 111 | 3.75 mA | ||
| D12-D11 | LVDS SW Default 01 | LVDS driver internal switch setting – correct range must be set for setting in D15-D13 | |||
| 01 | 2 mA to 2.75 mA | ||||
| 11 | 3mA to 3.75mA | ||||
| D10-D9 | Internal LVDS Termination Default 00 | Internal termination | |||
| 00 | 2 kΩ | ||||
| 01 | 200 Ω | ||||
| 10 | 200 Ω | ||||
| 11 | 100 Ω | ||||
| D4 | DACLK EN Default 1 | Enable DACLK output buffer | |||
| 0 | DACLK output buffer powered down | ||||
| 1 | DACLK output buffer enabled | ||||
| D1 | OVRA EN Default 1 | Enable OVRA output buffer | |||
| 0 | OVRA output buffer powered down | ||||
| 1 | OVRA output buffer enabled | ||||
| Register Address | Register Data | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A7-A0 in hex | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| 66 | LVDS Output Bus EN | |||||||||||||||
| D15-D0 | LVDS Output Bus EN Default FFFF | Individual LVDS output pin power down | |
| 0 | Output is powered down | ||
| 1 | Output is enabled | ||
| D15 | corresponds to TRDYP/N (pins N7, P7) | ||
| D14 | corresponds to HRESP/N (pins N6, P6) | ||
| D13 | SYNCOUTP/N (pins N5, P5) | ||
| D12 | Pins N4, P4 (no connect pins) which are not used and should be powered down for power savings | ||
| D11-D0 | corresponds to DA11-DA0 | ||