SLUS873C January   2009  – December 2016 UC1825A-SP

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Leading Edge Blanking
      2. 8.3.2 UVLO, Soft-Start, and Fault Management
      3. 8.3.3 Active Low Outputs During UVLO
      4. 8.3.4 Control Methods
      5. 8.3.5 Synchronization
      6. 8.3.6 High Current Outputs
      7. 8.3.7 Open Loop Test Circuit
    4. 8.4 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1  Auxiliary Supply Voltage
        2. 9.2.2.2  Oscillator Frequency
        3. 9.2.2.3  Preliminary Considerations
        4. 9.2.2.4  Input Power
        5. 9.2.2.5  Primary Current
        6. 9.2.2.6  Sense Resistor R(s)
        7. 9.2.2.7  MOSFET DC Losses
        8. 9.2.2.8  Selection of Core Material
        9. 9.2.2.9  Main Transformer Design
        10. 9.2.2.10 Calculation of Transformer
        11. 9.2.2.11 Minimum Core Size
        12. 9.2.2.12 Core Loss Limited Conditions
        13. 9.2.2.13 Core Geometry Selection
        14. 9.2.2.14 Wire Size Selection
        15. 9.2.2.15 Calculate Secondary RMS Current
        16. 9.2.2.16 Transformer Assembly
        17. 9.2.2.17 Calculation of Winding Resistances and Losses
        18. 9.2.2.18 Transformer Power Losses
        19. 9.2.2.19 Output Section
          1. 9.2.2.19.1 Output Choke Calculations
          2. 9.2.2.19.2 Output Capacitor
          3. 9.2.2.19.3 Output Diodes
        20. 9.2.2.20 UC1825A-SP PWM Control Section
          1. 9.2.2.20.1 Current Limit and Shutdown
          2. 9.2.2.20.2 Ramp
          3. 9.2.2.20.3 Slope Compensation
        21. 9.2.2.21 Closing the Feedback Loop
          1. 9.2.2.21.1 Error Amplifier
          2. 9.2.2.21.2 Control to Output Gain
          3. 9.2.2.21.3 Error Amplifier Compensation
          4. 9.2.2.21.4 Dynamic Performance
          5. 9.2.2.21.5 Short Circuit
          6. 9.2.2.21.6 Circuit Power Losses
        22. 9.2.2.22 Summary
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Feedback Traces
      2. 11.1.2 Input/Output Capacitors
      3. 11.1.3 Compensation Components
      4. 11.1.4 Traces and Ground Planes
      5. 11.1.5 Ground Planes
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 Receiving Notification of Documentation Updates
    4. 12.4 Community Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Pin Configuration and Functions

J Package
16-Pin CDIP
Top View
UC1825A-SP pinout_01_slus873.gif
HKT Package
16-Pin CFP
Top View

Pin Functions

PIN I/O DESCRIPTION
NAME NO.
CLK/LEB 4 O Output of the internal oscillator.
CT 6 I Timing capacitor connection pin for oscillator frequency programming. The timing capacitor must be connected to the device ground using minimal trace length.
EAOUT 3 O Output of the error amplifier for compensation.
GND 10 — Analog ground return pin.
ILIM 9 I Input to the current limit comparator.
INV 1 I Inverting input to the error amplifier.
NI 2 I Noninverting input to the error amplifier.
OUTA 11 O High current totem pole output A of the on-chip drive stage.
OUTB 14 O High current totem pole output B of the on-chip drive stage.
PGND 12 — Ground return pin for the output driver stage.
RAMP 7 I Noninverting input to the PWM comparator with 1.25-V internal input offset. In voltage mode operation, this serves as the input voltage feed-forward function by using the CT ramp. In peak current mode operation, this serves as the slope compensation input.
RT 5 I Timing resistor connection pin for oscillator frequency programming.
SS 8 I Soft-start input pin that also doubles as the maximum duty cycle clamp.
VC 13 — Power supply pin for the output stage. This pin must be bypassed with a 0.1-μF monolithic ceramic low ESL capacitor with minimal trace lengths.
VCC 15 — Power supply pin for the device. This pin must be bypassed with a 0.1-μF monolithic ceramic low ESL capacitor with minimal trace lengths.
VREF 16 O 5.1-V reference. For stability, the reference must be bypassed with a 0.1-μF monolithic ceramic low ESL capacitor and minimal trace length to the ground plane.