ZHCSTJ5A October   2023  – February 2024 TPS274C65CP

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Diagrams
      2. 8.3.2 Programmable Current Limit
      3. 8.3.3 Protection Mechanisms
        1. 8.3.3.1 Over-current Protection
        2. 8.3.3.2 Short-Circuit Protection
          1. 8.3.3.2.1 VS During Short-to-Ground
        3. 8.3.3.3 Thermal Shutdown Behavior
        4. 8.3.3.4 Inductive-Load Switching-Off Clamp
        5. 8.3.3.5 Inductive Load Demagnetization
        6. 8.3.3.6 Thermal Shutdown
        7. 8.3.3.7 Undervoltage Protection on VS (UVP)
        8. 8.3.3.8 Undervoltage Lockout on Low Voltage Supply (VDD_UVLO)
        9. 8.3.3.9 Power-Up and Power-Down Behavior
      4. 8.3.4 Diagnostic Mechanisms
        1. 8.3.4.1 Fault Indication
        2. 8.3.4.2 Short-to-Battery and Open-Load Detection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Off
      2. 8.4.2 Active
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 IEC 61000-4-5 Surge
        2. 9.2.2.2 Loss of GND
        3. 9.2.2.3 Paralleling Channels
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 静电放电警告
    6. 10.6 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.3.3.1 Over-current Protection

When IOUT reaches the current limit threshold, ICL, the device registers an overcurrent fault and begins regulating the current at the set limit. When either switch is in the FAULT state, it is indicated on the corresponding STx pin. This protects the system against overload cases where the load attempts to draw more than the maximum rated current, so the TPS274C65 can recognize and limit current or shut off these cases. In the case of a slow overload with the device channel enabled for a while, the current limit levels are as shown in Figure 8-3.

GUID-20231017-SS0I-9BKH-0TDH-GVJPXQ70ZCKF-low.svg Figure 8-3 Overload Response
GUID-20231017-SS0I-L0ML-9RKW-3G47TCMN6XSW-low.svg Figure 8-4 Overcurrent Behavior

For more details on the current limiting functionality, please see Programmable Current Limit.