ZHCSP88A December   2022  – September 2023 TPS25762-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Recommended Components
    5. 7.5  Thermal Information
    6. 7.6  Buck-Boost Regulator
    7. 7.7  CC Cable Detection Parameters
    8. 7.8  CC VCONN Parameters
    9. 7.9  CC PHY Parameters
    10. 7.10 Thermal Shutdown Characteristics
    11. 7.11 Oscillator Characteristics
    12. 7.12 ADC Characteristics
    13. 7.13 TVS Parameters
    14. 7.14 Input/Output (I/O) Characteristics
    15. 7.15 BC1.2 Characteristics
    16. 7.16 I2C Requirements and Characteristics
    17. 7.17 Typical Characteristics
  9. 8 Parameter Measurement Information
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Device Power Management and Supervisory Circuitry
        1. 9.3.1.1 VIN UVLO and Enable/UVLO
        2. 9.3.1.2 Internal LDO Regulators
      2. 9.3.2  TVSP Device Configuration and ESD Protection
      3. 9.3.3  Buck-Boost Regulator
        1. 9.3.3.1  Buck-Boost Regulator Operation
        2. 9.3.3.2  Switching Frequency, Frequency Dither, Phase-Shift and Synchronization
        3. 9.3.3.3  VIN Supply and VIN Over-Voltage Protection
        4. 9.3.3.4  Feedback Paths and Error Amplifiers
        5. 9.3.3.5  Transconductors and Compensation
        6. 9.3.3.6  Output Voltage DAC, Soft-Start and Cable Droop Compensation
        7. 9.3.3.7  VBUS Overvoltage Protection
        8. 9.3.3.8  VBUS Undervoltage Protection
        9. 9.3.3.9  Current Sense Resistor (RSNS) and Current Limit Operation
        10. 9.3.3.10 Buck-Boost Peak Current Limits
      4. 9.3.4  USB-PD Physical Layer
        1. 9.3.4.1 USB-PD Encoding and Signaling
        2. 9.3.4.2 USB-PD Bi-Phase Marked Coding
        3. 9.3.4.3 USB-PD Transmit (TX) and Receive (Rx) Masks
        4. 9.3.4.4 USB-PD BMC Transmitter
        5. 9.3.4.5 USB-PD BMC Receiver
        6. 9.3.4.6 Squelch Receiver
      5. 9.3.5  VCONN
      6. 9.3.6  Cable Plug and Orientation Detection
        1. 9.3.6.1 Configured as a Source
        2. 9.3.6.2 Configured as a Sink
        3. 9.3.6.3 Overvoltage Protection (Px_CC1, Px_CC2)
      7. 9.3.7  ADC
        1. 9.3.7.1 ADC Divider Ratios
      8. 9.3.8  BC 1.2, Legacy and Fast Charging Modes (Px_DP, Px_DM)
      9. 9.3.9  USB2.0 Low-Speed Endpoint
      10. 9.3.10 Digital Interfaces
        1. 9.3.10.1 General GPIO
        2. 9.3.10.2 I2C Buffer
      11. 9.3.11 I2C Interface
        1. 9.3.11.1 I2C Interface Description
        2. 9.3.11.2 I2C Clock Stretching
        3. 9.3.11.3 I2C Address Setting
        4. 9.3.11.4 Unique Address Interface
        5. 9.3.11.5 I2C Pullup Resistor Calculation
      12. 9.3.12 Digital Core
        1. 9.3.12.1 Device Memory
        2. 9.3.12.2 Core Microprocessor
      13. 9.3.13 NTC Input
      14. 9.3.14 Thermal Sensors and Thermal Shutdown
    4. 9.4 Device Functional Modes
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Application GUI Selections
        2. 10.2.2.2 EEPROM Selection
        3. 10.2.2.3 EN/UVLO
        4. 10.2.2.4 Sense Resistor, RSNS, RCSP, RCSN and CFILT
        5. 10.2.2.5 Inductor Currents
        6. 10.2.2.6 Output Capacitor
        7. 10.2.2.7 Input Capacitor
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  14. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 接收文档更新通知
    3. 13.3 支持资源
    4. 13.4 Trademarks
    5. 13.5 静电放电警告
    6. 13.6 术语表
  15. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

10.2.2.1 Application GUI Selections

Use the application GUI to select the desired operating conditions. Once complete, save the settings to the programming PC, flash the firmware to EEPROM, and power cycle device. Once complete the TPS25762-Q1 will be ready for operation.

Table 10-4 Application GUI Selections
PARAMETERGUI SELECTION
BUCK-BOOST AND USB INPUTS
Port A VBUS Power65 W
Port A PDOs and APDOs

PDO: 5 V, 3 A; 9 V, 3 A; 15 V, 3 A; 20 V, 3.25 A

APDO: 3.3 - 21 V, 3A

Port A VCONN Power0.1 W
fSW Switching Frequency400 kHz
L Inductor4.7 µH
Automotive Module Maximum Current15 A
LOW BATTERY INPUTS
Engine ON voltage12.5 V
Engine OFF voltage11 V
Run timer after engine off600 seconds
THERMAL MANAGEMENT INPUTS
VNTC_PHASE11.65 V
NTC_PHASE1 Power as Percentage of MAX50 %
VNTC_PHASE22.1 V
NTC_PHASE2 Power as Percentage of MAX30 %
VNTC_PHASE32.4 V
NTC_PHASE3 Power as Percentage of MAX0 % (disable PA_VBUS)