主页 放大器 可编程和可变增益放大器（PGA 和 VGA）
主页
放大器
可编程和可变增益放大器（PGA 和 VGA）

PGA309-HT

正在供货

电压输出可编程传感器调节器，PGA309-HT

立即订购
数据表

PGA309-HT

正在供货
数据表 立即订购

产品详情

PGA/VGA PGA Number of channels 2 Vs (min) (V) 2.7 Vs (max) (V) 5.5 Input type Differential Output type Single-ended Input offset drift (±) (typ) (µV/°C) 0.2 Interface type 1-wire, Analog 2 Wire, UART Noise at 1 kHz (typ) (V√Hz) 0.00000021 BW at Acl (MHz) 2 Acl, min spec gain (V/V) 4 Gain (max) (dB) 42 Architecture CMOS Features High Temperature, Temperature sensing Vos (offset voltage at 25°C) (typ) (mV) 0.003 Input voltage noise (typ) (µV√Hz) 0.21 Slew rate (typ) (V/µs) 0.5 Iq per channel (typ) (mA) 1.2 Gain error (typ) (%) 0.2 Gain drift (max) (ppm/°C) 10 Rating High Temp Operating temperature range (°C) -55 to 150
PGA/VGA PGA Number of channels 2 Vs (min) (V) 2.7 Vs (max) (V) 5.5 Input type Differential Output type Single-ended Input offset drift (±) (typ) (µV/°C) 0.2 Interface type 1-wire, Analog 2 Wire, UART Noise at 1 kHz (typ) (V√Hz) 0.00000021 BW at Acl (MHz) 2 Acl, min spec gain (V/V) 4 Gain (max) (dB) 42 Architecture CMOS Features High Temperature, Temperature sensing Vos (offset voltage at 25°C) (typ) (mV) 0.003 Input voltage noise (typ) (µV√Hz) 0.21 Slew rate (typ) (V/µs) 0.5 Iq per channel (typ) (mA) 1.2 Gain error (typ) (%) 0.2 Gain drift (max) (ppm/°C) 10 Rating High Temp Operating temperature range (°C) -55 to 150
TSSOP (PW) 16 32 mm² (5 mm × 6.4 mm)
  • Complete Bridge Sensor Conditioner
  • Voltage Output: Ratiometric or Absolute
  • Digital Cal: No Potentiometers/Sensor Trims
  • Sensor Error Compensation
    • Span, Offset, and Temperature Drifts
  • Low Error, Time-Stable
  • Sensor Linearization Circuitry
  • Temperature Sense: Internal or External
  • Calibration Lookup Table Logic
    • Uses External EEPROM (SOT23-5)
  • Over/Under-Scale Limiting
  • Sensor Fault Detection
  • +2.7V TO +5.5V Operation
  • Small TSSOP-16 Package
  • Complete Bridge Sensor Conditioner
  • Voltage Output: Ratiometric or Absolute
  • Digital Cal: No Potentiometers/Sensor Trims
  • Sensor Error Compensation
    • Span, Offset, and Temperature Drifts
  • Low Error, Time-Stable
  • Sensor Linearization Circuitry
  • Temperature Sense: Internal or External
  • Calibration Lookup Table Logic
    • Uses External EEPROM (SOT23-5)
  • Over/Under-Scale Limiting
  • Sensor Fault Detection
  • +2.7V TO +5.5V Operation
  • Small TSSOP-16 Package

The PGA309 is a programmable analog signal conditioner designed for bridge sensors. The analog signal path amplifies the sensor signal and provides digital calibration for zero, span, zero drift, span drift, and sensor linearization errors with applied stress (pressure, strain, etc.). The calibration is done via a One-Wire digital serial interface or through a Two-Wire industry-standard connection. The calibration parameters are stored in external nonvolatile memory (typically SOT23-5) to eliminate manual trimming and achieve long-term stability.

The all-analog signal path contains a 2x2 input multiplexer (mux), auto-zero programmable-gain instrumentation amplifier, linearization circuit, voltage reference, internal oscillator, control logic, and an output amplifier. Programmable level shifting compensates for sensor dc offsets.

The core of the PGA309 is the precision, low-drift, no 1/f noise Front-End PGA (Programmable Gain Amplifier). The overall gain of the Front-End PGA + Output Amplifier can be adjusted from 2.7V/V to 1152V/V. The polarity of the inputs can be switched through the input mux to accommodate sensors with unknown polarity output. The Fault Monitor circuit detects and signals sensor burnout, overload, and system fault conditions.

For reference application information, see the commercial device PGA309 User's Guide (SBOU024) available for download at www.ti.com.

The PGA309 is a programmable analog signal conditioner designed for bridge sensors. The analog signal path amplifies the sensor signal and provides digital calibration for zero, span, zero drift, span drift, and sensor linearization errors with applied stress (pressure, strain, etc.). The calibration is done via a One-Wire digital serial interface or through a Two-Wire industry-standard connection. The calibration parameters are stored in external nonvolatile memory (typically SOT23-5) to eliminate manual trimming and achieve long-term stability.

The all-analog signal path contains a 2x2 input multiplexer (mux), auto-zero programmable-gain instrumentation amplifier, linearization circuit, voltage reference, internal oscillator, control logic, and an output amplifier. Programmable level shifting compensates for sensor dc offsets.

The core of the PGA309 is the precision, low-drift, no 1/f noise Front-End PGA (Programmable Gain Amplifier). The overall gain of the Front-End PGA + Output Amplifier can be adjusted from 2.7V/V to 1152V/V. The polarity of the inputs can be switched through the input mux to accommodate sensors with unknown polarity output. The Fault Monitor circuit detects and signals sensor burnout, overload, and system fault conditions.

For reference application information, see the commercial device PGA309 User's Guide (SBOU024) available for download at www.ti.com.
filter 查找其他 可编程和可变增益放大器（PGA 和 VGA）
下载 观看带字幕的视频 视频

技术文档

未找到结果。请清除搜索并重试。
查看全部 1
顶层文档 类型 标题 格式选项 下载最新的英语版本 日期
* 数据表 Voltage Output Programmable Sensor Conditioner, PGA309-HT 数据表 (Rev. A) 2013-12-26

设计与开发

如需其他信息或资源，请点击以下任一标题进入详情页面查看（如有）。

封装 引脚 CAD 符号、封装和 3D 模型
TSSOP (PW) 16 Ultra Librarian
适用于评估类项目的 TI 标准条款与条件。

订购和质量

支持和培训

可获得 TI 工程师技术支持的 TI E2E™ 论坛

查看全部论坛主题 查看英文版全部论坛主题

所有内容均由 TI 和社区贡献者按“原样”提供，并不构成 TI 规范。请参阅使用条款。

如果您对质量、包装或订购 TI 产品有疑问，请参阅 TI 支持。​​​​​​​​​​​​​​

视频