LP87524J-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
- Input Voltage: 2.8 V to 5.5 V
- Output Voltage: 0.6 V to 3.36 V
- Four High-Efficiency Step-Down DC-DC Converter Cores:
- Total Output Current Up To 10 A
- Output Voltage Slew-Rate 3.8 mV/µs
- 4-MHz Switching Frequency
- Spread-Spectrum Mode and Phase Interleaving
- Configurable General Purpose I/O (GPIOs)
- I2C-Compatible Interface which Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
- Interrupt Function with Programmable Masking
- Programmable Power Good Signal (PGOOD)
- Output Short-Circuit and Overload Protection
- Overtemperature Warning and Protection
- Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)
The LP87524B/J/P-Q1 is designed to meet the power management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC-DC converter cores, which are configured as 4 single phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.
The automatic PFM/PWM (AUTO mode) operation maximizes efficiency over a wide output-current range. The LP87524B/J/P-Q1 supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) thus improving the accuracy of the output voltage. In addition the switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.
The LP87524B/J/P-Q1 device supports load-current measurement without the addition of external current-sense resistors. In addition, the LP87524B/J/P-Q1 supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can also include GPIO signals to control external regulators, load switches and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output voltage overshoot and the in-rush current.
관심 가지실만한 유사 제품
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능
비교 대상 장치와 유사한 기능
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | LP87524B/J/P-Q1 Four 4-MHz Buck Converters for AWR and IWR MMICs datasheet (Rev. B) | PDF | HTML | 2018/12/06 |
| User guide | LP87524x-Q1 Technical Reference Manual (Rev. A) | PDF | HTML | 2021/05/10 | |
| Application brief | The Benefits of FlexPower PMIC Devices (Rev. B) | PDF | HTML | 2020/11/23 | |
| Application note | Power Management Optimizations - Low Cost LC Filter Solution (Rev. A) | PDF | HTML | 2020/11/11 | |
| Application note | XWR1xxx Power Management Optimizations - Low Cost LC Filter Solution | 2017/10/16 |
설계 및 개발
전원 공급 솔루션
LP87524J-Q1을 포함하는 솔루션을 살펴보세요. TI는 칩(SoC), 프로세서, 마이크로컨트롤러, 센서 또는 FPGA(Field Programmable Gate Array)의 TI와 비TI 시스템을 위한 전원 공급 솔루션을 제공합니다.
AWR1843AOPEVM — 단일 칩 76GHz~81GHz 차량용 레이더 센서용 AWR1843AOP 평가 모듈(EVM)
AWR1843 AoP(안테나 온 패키지) 평가 모듈(EVM)은 MMWAVEICBOOST 및 DCA1000EVM 개발 키트(별도 판매)에 대한 직접 연결을 사용하여 AWR1843AOP mmWave 레이더 센서를 평가하기 위한 사용하기 쉬운 플랫폼입니다.
AWR1843AOPEVM에는 온칩 C67x DSP 코어와 저전력 Arm® Cortex® R4F 프로세서용 소프트웨어 개발을 시작하는 데 필요한 모든 것이 포함되어 있습니다.
LP87524Q1EVM — LP87524-Q1 쿼드 출력, 단상 벅 컨버터 평가 모듈
MMWAVEICBOOST — mmWave 센서 캐리어 카드 플랫폼
MMWAVEICBOOST 캐리어 카드는 일부 60GHz mmWave 평가 모듈의 기능을 확장합니다. 이 보드는 TI의 Code Composer 호환 디버거를 통해 추적 및 단일 스텝과 같은 고급 소프트웨어 개발, 디버그 기능을 제공합니다. 온보드 LaunchPad 인터페이스를 이용하면 추가 센서 및 무선 연결을 위해 TI의 BoosterPack™ 호환 하드웨어와 페어링할 수 있습니다. TI의 LaunchPad 에코시스템은 더 넓은 주변 기기 세트와 연결에 대한 MMWAVEICBOOST 액세스를 지원합니다.
(...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VQFN-HR (RNF) | 26 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.