LP87524P-Q1
AWR 및 AWR MIC용 차량용 다중 위상 4MHz, 3A/1.0V + 3A/1.0V + 2.5A/1.8V + 1.5A/1.2V 벅 컨버터
LP87524P-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
- Input Voltage: 2.8 V to 5.5 V
- Output Voltage: 0.6 V to 3.36 V
- Four High-Efficiency
Step-Down DC-DC Converter Cores:
- Total Output Current Up To 10 A
- Output Voltage Slew-Rate 3.8 mV/µs
- 4-MHz Switching Frequency
- Spread-Spectrum Mode and Phase Interleaving
- Configurable General Purpose I/O (GPIOs)
- I2C-Compatible Interface which Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
- Interrupt Function with Programmable Masking
- Programmable Power Good Signal (PGOOD)
- Output Short-Circuit and Overload Protection
- Overtemperature Warning and Protection
- Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)
The LP87524B/J/P-Q1 is designed to meet the power management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC-DC converter cores, which are configured as 4 single phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.
The automatic PFM/PWM (AUTO mode) operation maximizes efficiency over a wide output-current range. The LP87524B/J/P-Q1 supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) thus improving the accuracy of the output voltage. In addition the switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.
The LP87524B/J/P-Q1 device supports load-current measurement without the addition of external current-sense resistors. In addition, the LP87524B/J/P-Q1 supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can also include GPIO signals to control external regulators, load switches and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output voltage overshoot and the in-rush current.
관심 가지실만한 유사 제품
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | LP87524B/J/P-Q1 Four 4-MHz Buck Converters for AWR and IWR MMICs datasheet (Rev. B) | PDF | HTML | 2018. 12. 6 | |
| * | 사용 설명서 | LP87524x-Q1 Technical Reference Manual (Rev. A) | PDF | HTML | 2021. 5. 10 | |
| Application brief | The Benefits of FlexPower PMIC Devices (Rev. B) | PDF | HTML | 2020. 11. 23 |
설계 및 개발
전원 공급 솔루션
LP87524P-Q1을 포함하는 솔루션을 살펴보세요. TI는 칩(SoC), 프로세서, 마이크로컨트롤러, 센서 또는 FPGA(Field Programmable Gate Array)의 TI와 비TI 시스템을 위한 전원 공급 솔루션을 제공합니다.
LP87524Q1EVM — LP87524-Q1 쿼드 출력, 단상 벅 컨버터 평가 모듈
TIDEP-01012 — 계단식 mmWave 센서를 사용하는 이미징 레이더 레퍼런스 설계
캐스케이드 개발 키트의 두 가지 주요 사용 사례는 다음과 같습니다.
- mmWave Studio 툴을 사용하여 AWR2243 4칩 캐스케이드의 성능을 평가하기 위해 MMWCAS-DSP-EVM을 캡처 카드로 사용하려면 TIDEP-01012 설계 가이드를 참조하세요.
- 레이더 실시간 소프트웨어 애플리케이션을 개발하기 위해 MMWCAS-DSP-EVM을 사용하려면 TIDEP-01017 설계 가이드를 참조하세요.
이 레퍼런스 설계는 캐스케이드 이미징 레이더 무선 주파수(RF) 시스템을 사용합니다. 캐스케이드 레이더 장치는 향상된 각도 해상도 성능을 (...)
TIPA-050046 — LP87524J-Q1을 사용하는mmWave AWR1642 및 AWR1243 전원 공급 장치 설계
이 전원 공급 장치 설계는 AWR1642 및 AWR1243 레이더 센서에 전원을 공급하는 최적화된 전력 관리 IC(PMIC)를 설명합니다. 기술 레퍼런스 매뉴얼은 OTP 메모리를 다운로드한 후 LP87524B/J/P-Q1 기본 레지스터 비트에 대한 레퍼런스로 사용됩니다. 이러한 LP87524B/J/P-Q1 PMIC는 또한 장치가 LC 필터를 사용하여 노이즈 및 리플 사양을 충족하므로 외부 LDO가 없는 xWR 레이더 장치 간의 일반적인 연결을 보여줍니다.
TIPA-050047 — LP87524P-Q1을 사용하는mmWave AWR1642 및 AWR1243 전원 공급 장치 설계
이 전원 공급 장치 설계는 AWR1642 및 AWR1243 레이더 센서에 전원을 공급하는 최적화된 전력 관리 IC(PMIC)를 설명합니다. 기술 레퍼런스 매뉴얼은 OTP 메모리를 다운로드한 후 LP87524B/J/P-Q1 기본 레지스터 비트에 대한 레퍼런스로 사용됩니다. 이러한 LP87524B/J/P-Q1 PMIC는 또한 장치가 LC 필터를 사용하여 노이즈 및 리플 사양을 충족하므로 외부 LDO가 없는 xWR 레이더 장치 간의 일반적인 연결을 보여줍니다.
TIPA-050048 — LP87524B-Q1을 사용하는mmWave AWR1642 및 AWR1243 전원 공급 장치 설계
이 전원 공급 장치 설계는 AWR1642 및 AWR1243 레이더 센서에 전원을 공급하는 최적화된 전력 관리 IC(PMIC)를 설명합니다. 기술 레퍼런스 매뉴얼은 OTP 메모리를 다운로드한 후 LP87524B/J/P-Q1 기본 레지스터 비트에 대한 레퍼런스로 사용됩니다. 이러한 LP87524B/J/P-Q1 PMIC는 또한 장치가 LC 필터를 사용하여 노이즈 및 리플 사양을 충족하므로 외부 LDO가 없는 xWR 레이더 장치 간의 일반적인 연결을 보여줍니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VQFN-HR (RNF) | 26 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.