LM251772-Q1
- Input range from 3.5V to 36V
- Dynamical Vo
programming using I2C from:
- 3.3V up to in 20mV monotonous steps
- 1V up to 23V in 10mV monotonous steps
- Peak current regulation control
- Small voltage transition ripple overall operating modes
- Dynamic output voltage tracking (digital PWM
tracking input, analog tracking input)
- Via I2C interface programming
- Shut down quiescent current 3µA
- Operating quiescent current 60µA
- Drive (DRV) pin for dual role
port power path
- Push-Pull output for fast pMOS FET control
- Configurable as charge pump driver stage for nMOS FET
- Operation mode selection for high efficiency in
light load and high load conditions:
- Power save mode (Single Pulse/µSleep)
- Automatic conduction mode
- Integrated high voltage supply LDO
- Auxiliary high voltage LDO for microcontroller supply
- Integrated full-bridge gate drive
- 2A peak current capability
- Bootstrap over and under-voltage protection
- Integrated boot-strap diode
- Fixed frequency independent from operating mode
(boost, buck-boost, buck)
- Forced PWM mode selectable
- Switching frequency from 100kHz to 2200kHz
- External clock synchronization and clock output
- Spread spectrum operation selectable
- Average input or output current sensor
- Programmable from 0.5A to 7A in 50mA steps
- I2C programmable with diagnostics
- Automotive temperature range (Tj = -40°C to 150°C)
- 40-Pin WSON package with wettable flanks
- Functional Safety-Capable
-
Create a custom design using the LM251772-Q1 with the WEBENCH® Power Designer
The LM251772-Q1 is a four switch Buck-Boost controller. The device provides a regulated output voltage if the input voltage is higher, equal or lower than the adjusted output voltage. In power save mode the device supports very high efficiency over the complete operation range of the output. The output voltage and average current is dynamically programmable using the integrated I2C interface. The configuration range for output voltage and average current meets the USB-PD standard requirements. The integrated DRV pin is used to control an optional disconnect FET if the system is targeted to support dual role port (DRP) requirements.
LM251772-Q1 runs at a fixed switching frequency, which is set using the RT/SYNC pin. The switching frequency remains the same during buck, boost and buck-boost operation. The device maintains small mode transition ripple over all operating modes.
관심 가지실만한 유사 제품
비교 대상 장치보다 업그레이드된 기능을 지원하는 즉각적 대체품.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | LM251772-Q1 36V VIN 4 Switch Buck-Boost Controller With I2C for datasheet | PDF | HTML | 2025. 10. 27 | |
| 기능 안전 정보 | LM51772-Q1 and LM251772-Q1 Functional Safety FIT Rate and FMD | PDF | HTML | 2025. 5. 5 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
LM251772EVM-PD — LM251772 평가 모듈
LM251772Q1EVM-PD — LM251772-Q1 평가 모듈
LM251772-QUICKSTART-CALC — LM251772 BuckBoost Quickstart Calculator Tool
TPS61383Q-SCAP-CALC — TPS61383-Q1 Super Capacitor Energy Calculation Tool.
PMP31344 — DisplayPort™ 대체 모드를 지원하는 차량용, 12V 입력, 140W 2포트 USB Power Delivery 레퍼런스 설계
이 레퍼런스 설계는 두 개의 USB Type-C® 포트에 전원과 디지털 통신을 모두 제공하는 차량용 USB EPR(확장 전력 범위) 시스템을 보여줍니다. USB-C 케이블을 연결할 때 TPS26744E-Q1은 연결된 장치와 대상 출력 전압 및 최대 전류를 협상합니다. 그런 다음 컨트롤러가 전력 전송을 처리하는 벅 부스트 컨트롤러(LM251772)를 활성화하고 적절하게 구동합니다.
통신 측면에서 TPS26744E-Q1은 USB-DP 모드 선택을 위해 휴대폰 또는 랩톱 등 연결된 USB 장치와 협상할 수 있습니다. 그런 다음 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VQFN (RHA) | 40 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.