AM2431
- Up to 2× Dual-core Arm Cortex-R5F MCU subsystems operating at up to 800MHz, highly-integrated for
real-time processing
- Dual-core Arm Cortex-R5F clusters support dual-core and single-core operation
- 32KB I-cache and 32KB D-cache per R5F core with SECDED ECC on all memories
- Single-core: 128KB TCM per cluster (128KB TCM per R5F core)
- Dual-core: 128KB TCM per cluster (64KB TCM per R5F core)
- 1× Single-core Arm Cortex-M4F MCU at up to 400MHz
- 256KB SRAM with SECDED ECC
- Up to 2MB of On-chip RAM (OCSRAM) with
SECDED ECC:
- Can be divided into smaller banks in increments of 256KB for as many as 8 separate memory banks
- Each memory bank can be allocated to a single core to facilitate software task partitioning
- DDR Subsystem (DDRSS)
- Supports LPDDR4, DDR4 memory types
- 16-bit data bus with inline ECC
- Supports speeds up to 1600 MT/s
- Device Management Security Controller
(DMSC-L)
- Centralized SoC system controller
- Manages system services including initial boot, security, and clock/reset/power management
- Communication with various processing units over message manager
- Simplified interface for optimizing unused peripherals
- On-Chip Debug functionality through JTAG and Trace interfaces)
- Data Movement Subsystem (DMSS)
- Block Copy DMA (BCDMA)
- Packet DMA (PKTDMA)
- Secure Proxy (SEC_PROXY)
- Ring Accelerator (RINGACC)
- Time Sync Subsystem
- Central Platform Time Sync (CPTS) module
- Timer Manager (TIMERMANAGER) with 1024 timers
- Time Sync and Compare event interrupt routers
- 2× Gigabit Industrial Communication
Subsystems (PRU_ICSSG)
- Optional support for Profinet IRT, Profinet RT, EtherNet/IP, EtherCAT, Time-Sensitive Networking (TSN), and other Networking Protocols
- Backwards compatibility with 10/100Mb PRU-ICSS
- Each PRU_ICSSG contains:
- 3× PRU RISC Cores per Slice (2×
Slice per PRU_ICSSG)
- PRU General Use core (PRU)
- PRU Real-Time Unit core (PRU-RTU)
- PRU Transmit core (PRU-TX)
- Each PRU core supports the
following features:
- Instruction RAM with ECC
- Broadside RAM
- Multiplier with optional accumulator (MAC)
- CRC16/32 hardware accelerator
- Byte swap for Big/Little Endian conversion
- SUM32 hardware accelerator for UDP checksum
- Task Manager for preemption support
- Up to 2× Ethernet ports
- RGMII (10/100/1000)
- MII (10/100)
- Three Data RAMs with ECC
- 8 banks of 30 × 32-bit register scratchpad memory
- Interrupt controller and task manager
- 2× 64-bit Industrial Ethernet Peripherals (IEPs) for time stamping and other time synchronization functions
- 18× Sigma-Delta Filter Module
(SDFM) interfaces
- Short circuit logic
- Over-current logic
- 6× Multi-protocol position encoder interfaces
- 1× Enhanced Capture Module (ECAP)
- 16550-compatible UART
- Dedicated 192MHz clock to support 12Mbps PROFIBUS
- 3× PRU RISC Cores per Slice (2×
Slice per PRU_ICSSG)
- Secure boot supported
- Hardware-enforced Root-of-Trust (RoT)
- Support to switch RoT via backup key
- Support for takeover protection, IP protection, and anti-roll back protection
- Security co-processor (DMSC-L) for key
and security management, with dedicated device level interconnect for security
- Secure watchdog/timer/IPC
- Extensive firewall support for isolation
- Cryptographic acceleration supported
- Session-aware cryptographic engine
with ability to auto-switch key-material based on incoming data stream
- Supports cryptographic cores
- AES – 128-/192-/256-Bit key sizes
- SHA2 – 224-/256-/384-/512-Bit key sizes
- DRBG with true random number generator
- PKA (Public Key Accelerator) to Assist in RSA/ECC processing for secure boot
- Session-aware cryptographic engine
with ability to auto-switch key-material based on incoming data stream
- Debugging security
- Secure software controlled debug access
- Security aware debugging
- 6× Inter-Integrated Circuit (I2C) ports
- 9× Universal Asynchronous Receive/Transmit (UART) modules
- 1× 12-bit Analog-to-Digital Converters
(ADC)
- Configurable sample rate up to 4MSPS
- 8× multiplexed analog inputs
- 7× Multichannel Serial Peripheral Interfaces (SPI) controllers
- 3× General-Purpose I/O (GPIO) modules
- 9× Enhanced Pulse-Width Modulator (EPWM) modules
- 3× Enhanced Capture (ECAP) modules
- 3× Enhanced Quadrature Encoder Pulse (EQEP) modules
- 2× Modular Controller Area Network (MCAN) modules with full CAN-FD support
- 2× Fast Serial Interface Transmitter (FSITX) cores
- 6× Fast Serial Interface Receiver (FSIRX) cores
High-speed interfaces:
- 1× Integrated Ethernet switch supporting:
(CPSW)
- Up to 2 external Ethernet ports
- RGMII (10/100/1000)
- RMII (10/100)
- IEEE 1588 (2008 Annex D, Annex E, Annex F) with 802.1AS PTP
- Clause 45 MDIO PHY management
- Energy efficient Ethernet (802.3az)
- Up to 2 external Ethernet ports
- 1× PCI-Express Gen2 controller (PCIE)
- Supports Gen2 Single Lane operation
- 1× USB 3.1 Dual-Role Device (DRD)
Subsystem (USBSS)
- Port configurable as USB Host, USB Device, or USB Dual-Role device
- USB Device: High-speed (480Mbps) and Full-speed (12Mbps)
- USB Host: SuperSpeed Gen1 (5Gbps), High-speed (480Mbps), Full-speed (12Mbps), and Low-speed (1.5Mbps)
- Integrated USB VBUS detection
- 1× Serializer/Deserializer (SERDES)
- One SERDES PHY lane to support eitherPCI-Express Gen2 or USB SuperSpeed Gen1
- 2× Multimedia Card/Secure Digital (MMCSD)
interfaces
- One 8-bit for eMMC (MMCSD0)
- One 4-bit for MMCSD/SDIO (MMCSD1)
- Integrated analog switch for voltage switching from 3.3V to 1.8V for high-speed cards
- 1× General-Purpose Memory Controller
(GPMC)
- 16-bit parallel bus with 133MHz clock or
- 32-bit parallel bus with 100MHz clock
- Error Location Module (ELM) support
- 1× Flash Subsystem (FSS) for external
memory configurable as either:
- 1× Octal SPI (OSPI) flash interface
- or 1× Quad SPI (QSPI) flash interface
- Simplified power sequencing requirements
- Dual-voltage I/O Support (3.3V / 1.8V)
- Integrated SDIO LDO for handling automatic voltage transition for SD interface
- Integrated voltage supervisor for monitoring over-voltage and under-voltage conditions
- Integrated power supply glitch detector for detecting fast supply transients
Functional safety:
-
Functional Safety-Compliant
- Developed for functional safety applications
- Documentation available to aid IEC 61508 functional safety system design
- Systematic capability up to SIL 3
- Hardware integrity up to SIL 2
- Safety-related certification
- ECC or parity on calculation-critical memories
- Built-In Self-Test (BIST) for CPU and on-chip RAM
- Error Signaling Module (ESM) with dedicated error pin
- ECC and parity on select internal bus interconnects
- Run-time safety diagnostics,
including:
- Voltage, Temperature, and Clock Monitoring
- Windowed Watchdog Timers
- CRC Engine for memory integrity checks
- MCU domain with dedicated memory,
interfaces, and M4FSS capable of isolation from the larger SoC with Freedom From
Interference (FFI) features:
- Separate interconnect
- Firewalls and timeout gaskets
- Controlled reset isolation
- Dedicated MCU PLL and MMR control
- Separate I/O voltage supply rail
- Supports boot from OSPI/QSPI Flash, SPI Flash, parallel NOR Flash, parallel NAND Flash, UART, I2C, MMCSD, eMMC, USB, PCIe, and Ethernet interfaces.
- 16-nm FinFET technology
- ALV: 17.2mm × 17.2mm, 0.8mm pitch(441-pin) [Lidded] Flip-Chip Ball Grid Array(FCBGA)
- ANI: 17.2mm × 17.2mm, 0.8mm pitch(441-pin) [Lidded] Flip-Chip Ball Grid Array(FCBGA)
- ALX: 11.0mm × 11.0mm, 0.5mm pitch(293-pin) [Overmolded] Flip-Chip Chip Scale Package(FCCSP)
AM243x is an extension of Sitara’s industrial-grade portfolio into high-performance microcontrollers. The AM243x device is built for industrial applications, such as motor drives and remote I/O modules, which require a combination of real-time communications and processing. The AM243x family provides scalable performance with up to four Cortex-R5F MCUs, one Cortex-M4F, and two instances of Sitara’s gigabit TSN-enabled PRU_ICSSG.
The AM243x SoC architecture was designed to provide best-in-class real-time performance through the high-performance Arm Cortex-R5F cores, Tightly-Coupled Memory (TCM) banks, configurable SRAM partitioning, and dedicated low-latency paths to and from peripherals for rapid data movement in and out of the SoC. This deterministic architecture allows for AM243x to handle the tight control loops found in servo drives while the peripherals like FSI, GPMC, ECAPs, PWMs, and encoder interfaces help enable a number of different architectures found in these systems.
The SoC provides flexible industrial communications capability including full protocol stacks for EtherCAT target, PROFINET device, EtherNet/IP adapter, and IO-Link Controller. The PRU_ICSSG further provides capability for gigabit and TSN based protocols. In addition, the PRU_ICSSG enables additional interfaces including a UART interface, sigma delta decimation filters, and absolute encoder interfaces.
Functional safety features can be enabled through the integrated Cortex-M4F along with dedicated peripherals which can all be isolated from the rest of the SoC. AM243x also supports secure boot.
관심 가지실만한 유사 제품
비교 대상 장치보다 업그레이드된 기능을 지원하는 즉각적 대체품.
기술 자료
설계 및 개발
전원 공급 솔루션
AM2431에 사용 가능한 전원 공급 솔루션을 찾아보세요. TI는 칩(SoC), 프로세서, 마이크로컨트롤러, 센서 또는 FPGA(Field Programmable Gate Array)의 TI와 비TI 시스템을 위한 전원 공급 솔루션을 제공합니다.
BOOSTXL-IOLINKM-8 — 8포트 IO-Link 마스터 BoosterPack™
이 BoosterPack™은 Sitara™ AM243x MCU를 지원하는 LP-AM243 TI LaunchPad™ 키트와 함께 작동하도록 설계되었습니다. 이 설계는 함께 결합되어 빠르고 결정성 있는 타이밍과 독립 주기 및 비트율 구성을 지원하는 8포트 IO-Link Master를 구현합니다. 이 설계를 사용하여 OPC UA, Profinet, EtherCAT. 또는 이더넷 IP에 연결하는 원격 IO 게이트웨이를 구축할 수 있습니다. Sitara™ 프로세서 기반 프레임 핸들러용 PRU(Programmable Real-Time (...)
BP-AM2BLDCSERVO — AM2x Brushless-DC (BLDC) Servo Motor BoosterPack
The AM2x BLDC Servo Motor BoosterPack plug-in module is an add-on for the AM2x LaunchPad development kits. This BoosterPack provides up to two axes of 24V/8A BLDC driver, ADC/SDFM current feedback, industrial absolute encoder, and resolver feedback.
LP-AM243 — Arm® 기반 MCU를 위한 AM243x 범용 LaunchPad™ 개발 키트
LP-AM243은 AM243x 시리즈의 Sitara™ 고성능 마이크로컨트롤러를 위한 개발 보드입니다. 이 보드는 다음 애플리케이션을 개발할 수 있는 표준화되고 사용하기 쉬운 플랫폼을 제공하므로 초기 평가 및 프로토타이핑에 이상적입니다. LP-AM243에는 소형 폼 팩터 Sitara AM2434 ALX 마이크로컨트롤러 유닛(MCU)과 추가 부품이 포함되어 있어 사용자가 산업용 이더넷, 표준 이더넷, 고속 직렬 인터페이스(FSI) 등을 포함한 다양한 디바이스 인터페이스를 사용하여 프로토타입을 쉽게 제작할 수 있습니다.
AM2434는 (...)
RIO-DEV-PLATFORM — Remote IO development platform for Arm-based MCUs with industrial Ethernet
The Remote IO Development Platform provides tailored combinations of hardware and software designed to make it quick and easy to establish remote I/O connections for a variety of applications. This platform can be used to build a remote IO gateway to connect to industrial protocols such as (...)
TMDS243DC01EVM — 고속 확장을 위한 AM243x 및 AM64x 평가 모듈 분리 보드
TMDS243DC01EVM은 AM243x 제품을 위한 고속 확장(HSE) 평가 모듈(EVM)입니다. 이 EVM은 AM243x EVM(TMDS243EVM)용 애드온 보드입니다.
TMDS243DC01EVM에는 TMDS243EVM의 HSE 커넥터에 포함된 모든 I/O 신호에 대한 테스트 액세스를 제공하는 범용 신호 분리가 포함되어 있습니다. 이 분리 보드에는 TMDS243EVM과 결합하기 위한 150핀 HSE 커넥터 및 20핀 ADC(아날로그-디지털 컨버터) 커넥터가 있습니다.
TMDS243EVM — Arm® Cortex®-R5F 기반 MCU용 AM243x 평가 모듈
TMDS243 평가 모듈(EVM)은 AM243x 기능을 평가하고 다양한 애플리케이션을 위한 프로토타입을 개발할 수 있는 독립형 테스트 및 개발 플랫폼입니다. TMDS243EVM에는 더 큰 폼 팩터의 Sitara™ AM2434 ALV MCU(마이크로컨트롤러 유닛)과 추가 부품이 포함되어 있어 사용자가 MCU의 보안 기능과 산업용 이더넷, 표준 이더넷, PCIe(주변 기기 구성 요소 상호 연결 익스프레스), FSI(고속 직렬 인터페이스 ) 등 다양한 장치 인터페이스를 활용하여 프로토타입을 쉽게 제작할 수 있습니다. 이 EVM은 더 (...)
TMDS64DC01EVM — AM64x IO 링크 및 고속 분리 카드
The AM64x IO-Link and high speed expansion board is an add-on module for the AM64x GP EVM. This board includes eight (8) IO-Link ports and general purpose signal breakout. The Breakout board section provides the test access to all the IO signals included on the High Speed Expansion (...)
PHYTC-3P-KIT-AM64 — phyBOARD®-AM64x개발 키트
phyBOARD®-AM64x 개발 키트는 SOM(시스템 온 모듈) 및 캐리어 보드로, 헤드리스 산업용 통신 시스템을 위한 견고하고 안정적인 임베디드 프로세서 보드인 phyCORE®-AM64x를 특징으로 합니다. 50mm x 37mm SOM에는 CAN, EtherCAT, UART, I2C와 같은 일반적인 공장 통신 프로토콜을 지원하는 광범위한 280핀 상호 연결이 있으며 EPWM, eCAP 및 EQEP와 같은 자동화 관련 인터페이스도 있습니다. TI AM64x 프로세서의 이종 아키텍처로 인해 Linux를 사용하여 대부분의 (...)
TQ-3P-SITARASOMS — TQ Group Sitara SOM
TQ-3P-SOM-TQMA243XL — TQ-Group TQMa243xL system on module for AM2434 Arm-based microcontroller
The embedded module TQMA243XL, is based on the processor family AM243x quad-core Arm® Cortex®-R5F-based MCU. This LGA (land grid array) module is designed to use the pin compatible processors on one module design. This module is ideally suited for headless applications with extended (...)
TMDSEMU110-U — XDS110 JTAG 디버그 프로브
텍사스 인스트루먼트 XDS110은 TI 임베디드 프로세서를 위한 새로운 디버그 프로브(에뮬레이터)입니다. XDS110은 XDS100 제품군을 대체하면서 하나의 포드로 더 다양한 표준(IEEE1149.1, IEEE1149.7, SWD)을지원합니다. 또한 모든 XDS 디버그 프로브는 ETB(Embedded Trace Buffer)가 포함되어 있는 모든 Arm® 및 DSP 프로세서에서 코어(Core) 및 시스템 트레이스(System Trace)를 지원합니다. 핀을 통한 코어 추적의 경우 XDS560v2 PRO TRACE가 필요합니다.
(...)TMDSEMU560V2STM-U — XDS560™ 소프트웨어 v2 시스템 추적 USB 디버그 프로브
XDS560v2는 디버그 프로브의 XDS560™ 제품군 중 최고의 성능을 가진 제품으로, 기존의 JTAG 표준(IEEE1149.1)과 cJTAG(IEEE1149.7)를 모두 지원합니다. SWD(직렬 와이어 디버그)는 지원하지 않습니다.
모든 XDS 디버그 프로브는 ETB(임베디드 추적 버퍼)가 있는 모든 ARM 및 DSP 프로세서에서 코어와 시스템 트레이스를 지원합니다. 핀을 통한 추적의 경우 XDS560v2 PRO TRACE가 필요합니다.
XDS560v2는 MIPI HSPT 60핀 커넥터(TI 14핀, TI 20핀 및 ARM (...)
TMDSEMU560V2STM-UE — XDS560v2 시스템 추적 USB 및 이더넷 디버그 프로브
The XDS560v2 is the highest performance of the XDS family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7). Note that it does not support serial wire debug (SWD).
All XDS debug probes support Core and System Trace in all ARM and DSP processors that (...)
LB-3P-TRACE32-ARM — Arm® 기반 마이크로컨트롤러 및 프로세서용 Lauterbach TRACE32® 디버그 및 트레이스 시스템
Lauterbach의 TRACE32® 툴은 개발자가 모든 종류의 Arm® 기반 마이크로컨트롤러 및 프로세서를 분석, 최적화 및 인증할 수 있도록 하는 첨단 하드웨어 및 소프트웨어 구성 요소 제품군입니다. 세계적으로 유명한 임베디드 시스템 및 SoC용 디버그 및 트레이스 솔루션은 초기 사전 실리콘 개발부터 현장의 제품 인증 및 문제 해결에 이르기까지 모든 개발 단계를 위한 완벽한 솔루션입니다. Lauterbach 툴의 직관적인 모듈형 설계는 엔지니어에게 현존하는 최고의 성능을 제공하고 요구 사항 변화에 따라 적응하고 성장하는 (...)
TSK-3P-BLUEBOX — TASKING BlueBox hardware debugger
TASKING’s Debug, Trace, and Test tools offer comprehensive solutions for efficient debugging, tracing, and testing of TI's embedded systems. The scalable TASKING BlueBox debuggers allow users to easily flash, debug, and test across TI's portfolio. Development on TI hardware is made even easier with (...)
INDUSTRIAL-COMMUNICATIONS-SDK-AM243X — Industrial Communications SDK for AM243x - RTOS
이 소프트웨어 개발 키트(SDK)에는 TI 프로세서에서 사용할 수 있는 실시간 산업용 통신 프로토콜(EtherCAT, EtherNet/IP, PROFINET, IO-Link 등)이 포함되어 있습니다. 또한 PRU-ICSS 펌웨어, 드라이버, 통신 스택 라이브러리 및 애플리케이션 예제와 함께 설명서가 있습니다.
새로운 기능:
- EtherCAT EoE를 통한 이더넷
- EtherCAT FoE를 통한 파일 액세스
- 영구 데이터 스토리지를 위한 NVM 라이브러리 통합 - EtherCAT 예제에서는 이제 플래시 메모리가 아닌 EEPROM을 사용하여 (...)
MCU-PLUS-SDK-AM243X — MCU+ SDK for AM243x – RTOS, No-RTOS
AM243x MCU(마이크로컨트롤러) 소프트웨어는 SDK(소프트웨어 개발 키트) 모음으로, 쉬운 설정과 예제, 벤치마크 및 데모에 대한 빠른 기본 액세스를 갖춘 TI 임베디드 프로세서를 위한 소프트웨어 플랫폼을 제공합니다. 이 소프트웨어는 기본 시스템 소프트웨어 기능을 처음부터 만들 필요를 없앴기 때문에 애플리케이션 개발 일정을 크게 단축할 수 있습니다.
AM243x 소프트웨어는 다음과 같습니다.
- MCU-PLUS-SDK-AM243X: MCU 플러스 SDK는 AM243x MCU에서 애플리케이션을 개발할 수 있는 기반 소프트웨어 및 (...)
MOTOR-CONTROL-SDK-AM243X — Motor Control SDK for AM243x - RTOS
AM243x MCU(마이크로컨트롤러) 소프트웨어는 SDK(소프트웨어 개발 키트) 모음으로, 쉬운 설정과 예제, 벤치마크 및 데모에 대한 빠른 기본 액세스를 갖춘 TI 임베디드 프로세서를 위한 소프트웨어 플랫폼을 제공합니다. 이 소프트웨어는 기본 시스템 소프트웨어 기능을 처음부터 만들 필요를 없앴기 때문에 애플리케이션 개발 일정을 크게 단축할 수 있습니다.
AM243x 소프트웨어는 다음과 같습니다.
- MCU-PLUS-SDK-AM243X: MCU 플러스 SDK는 AM243x MCU에서 애플리케이션을 개발할 수 있는 기반 소프트웨어 및 (...)
IBV-3P-ICECAT — 임베디드 시스템용 IBV EtherCAT MainDevice SDK
The icECAT EtherCAT Master Stack library by IBV is a Software Development Kit (SDK) for creating an EtherCAT MainDevice (master) system achieving best performance with lowest resource usage. It is especially designed for use on embedded systems with optimized Link Layer drivers with DMA support (...)
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)
DDR-CONFIG-AM24 — DDR Configuration Tool
SYSCONFIG — Standalone desktop version of SysConfig
CCStudio™ SysConfig is part of TI's extensive CCStudio™ development ecosystem and is a configuration tool that simplifies hardware and software configuration challenges to accelerate software development.
SysConfig provides an intuitive graphical user interface for configuring pins, peripherals, (...)
IAR-KICKSTART — IAR Embedded Workbench
IAR Embedded Workbench는 선택한 대상 마이크로컨트롤러를 위한 임베디드 애플리케이션을 빌드하고 디버깅하는 데 사용되는 완전한 개발 툴 체인을 제공합니다. 포함된 IAR C/C++ 컴파일러는 애플리케이션에 매우 최적화된 코드를 생성합니다. C-SPY 디버거는 복잡한 코드 및 데이터 중단점을 지원하는 소스 및 분해 수준 디버깅이 가능한 완전 통합된 디버거입니다.
주요 구성 요소:
- 프로젝트 관리 툴과 편집기가 포함된 통합 개발 환경입니다.
- 고도로 최적화된 C 및 C++ 컴파일러.
- 다중 파일 컴파일 지원.
- 런타임 라이브러리.
- 링커 (...)
TSK-3P-VX-TOOLSET — Arm용 TASKING VX-toolset
Arm용 VX-Toolset은 일부 Cortex-M 및 Cortex-R 코어 장치의 안전 필수 임베디드 소프트웨어 개발을 위해 인증된 컴파일러 툴체인입니다. Eclipse IDE 통합, 고급 멀티코어 지원, TASKING BlueBox 디버거와의 호환성을 제공하는 VX-toolset은 개발을 단순화합니다. 최대 ASIL D까지의 ISO 26262 및 ISO 21434 규격 준수를 위해 TÜV NORD 인증을 획득했습니다.
AM24X-ACADEMY — AM24x academy
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
GHS-3P-UVELOSITY — Green Hills Software u-velOSity Safety RTOS
The µ-velOSity™ Safety RTOS is the smallest of Green Hills Software's real-time operating systems and was designed especially for microcontrollers. It supports a wide range of TI processor families using the Arm® Cortex-M or Cortex-R cores as a main CPU or as a co-processors (...)
USIT-3P-SECIC-HSM — Uni-Sentry SecIC-HSM 펌웨어
SecIC-HSM은 MCU/SoC 칩에 필요한 사이버 보안 요건을 충족하도록 설계되었습니다. HSM 펌웨어는 자동차, 신에너지, 태양광, 로봇 공학, 헬스케어, 항공 등의 분야에 적용될 수 있습니다. 이용 가능한 사이버 보안 기능으로는 보안 부팅, SecOC(보안 통신), 보안 진단, 보안 스토리지, 보안 업데이트, 보안 디버깅 및 키 관리 등이 있습니다. SecIC-HSM의 장점: 여러 칩 시리즈와 종합적인 소프트웨어 호환성을 지원하는 원스톱 사이버 보안 솔루션으로, 업계를 선도하는 성능을 제공하며, 약 30곳의 OEM 대량 (...)
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.
UniFlash는 CCStudio™ 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.
macOS는 mmWave, AMx, K2G 및 (...)
SPRCAJ9 — AM243x SW Build Sheet
SPRM779 — AM64x Power Estimation Tool
TIDA-010234 — 8포트 IO-Link 마스터 레퍼런스 설계
TIDA-010256 — 128채널 초음파 트랜스미터 시스템 레퍼런스 설계
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| FCCSP (ALX) | 293 | Ultra Librarian |
| FCBGA (ALV) | 441 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.