主页 电池管理 IC 电池监测器和平衡器
主页
电池管理 IC
电池监测器和平衡器

BQ76PL536

不推荐用于新设计

用于电动汽车和混合动力电动汽车的锂离子电池监测器和二级保护 IC

立即订购
数据表
BQ76PL536 不推荐用于新设计
虽然我们会继续生产此产品供先前的设计使用，但不推荐在新设计中使用此产品。请考虑从这些替代产品中选择一款：
open-in-new 比较替代产品
功能与比较器件相同且具有相同引脚
BQ76PL536A 正在供货 用于工业电池组的 3 至 6 节串联锂离子电池监控器和二次保护 bq76PL536 is not recommended for new designs. Consider bq76PL536A for all new designs since this is a pin and function compatible device with improved communication functionality, noise immunity and ADC performance.

BQ76PL536

不推荐用于新设计
数据表 立即订购

产品详情

Features Cell balancing, LDO output, One-Time Programmable (OTP) memory, Overtemperature protection, Overvoltage protection, Precision ADC, SPI, Undervotlage protection Device type Cell monitor and balancer Operating temperature range (°C) -40 to 85 Rating Automotive Communication interface SPI
Features Cell balancing, LDO output, One-Time Programmable (OTP) memory, Overtemperature protection, Overvoltage protection, Precision ADC, SPI, Undervotlage protection Device type Cell monitor and balancer Operating temperature range (°C) -40 to 85 Rating Automotive Communication interface SPI
HTQFP (PAP) 64 144 mm² 12 x 12
  • 3 to 6 Series Cell Support, All Chemistries
  • Hot-Pluggable
  • High-Speed SPI for Data Communications
  • Stackable Vertical Interface
  • No Isolation Components Required Between ICs
  • Industrial Temperature Range, –40°C to 85°C
  • High-Accuracy Analog-to-Digital Converter (ADC):
    • ±3 mV Typical accuracy
    • 14-Bit Resolution, 6-µs Conversion Time
    • Nine ADC Inputs: 6 Cell Voltages, 1 Six-Cell Brick Voltage,
      2 Temperatures, 1 General-Purpose Input
    • Dedicated Pins for Synchronizing Measurements
  • Configuration Data Stored in ECC-OTP Registers
  • Built-In Comparators (Secondary Protector) for:
    • Over- and Undervoltage Protection
    • Overtemperature Protection
    • Programmable Thresholds and Delay Times
    • Dedicated Fault Output Signals for OV, UV, OT
  • Cell Balancing Control Outputs With Safety Timeout
    • Balance Current Set by External Components
  • Supply Voltage Range from 6 V to 30 V Continuous and 36 V Peak
  • Low Power:
    • Typical 12-µA Sleep, 45-µA Idle
  • Integrated Precision 5-V, 3-mA LDO
  • APPLICATIONS
    • Uninterruptible Power Systems (UPS)
    • E-Bike and E-Scooter
    • Large-Format Battery Systems
    • Electric and Hybrid Electric Vehicles
  • 3 to 6 Series Cell Support, All Chemistries
  • Hot-Pluggable
  • High-Speed SPI for Data Communications
  • Stackable Vertical Interface
  • No Isolation Components Required Between ICs
  • Industrial Temperature Range, –40°C to 85°C
  • High-Accuracy Analog-to-Digital Converter (ADC):
    • ±3 mV Typical accuracy
    • 14-Bit Resolution, 6-µs Conversion Time
    • Nine ADC Inputs: 6 Cell Voltages, 1 Six-Cell Brick Voltage,
      2 Temperatures, 1 General-Purpose Input
    • Dedicated Pins for Synchronizing Measurements
  • Configuration Data Stored in ECC-OTP Registers
  • Built-In Comparators (Secondary Protector) for:
    • Over- and Undervoltage Protection
    • Overtemperature Protection
    • Programmable Thresholds and Delay Times
    • Dedicated Fault Output Signals for OV, UV, OT
  • Cell Balancing Control Outputs With Safety Timeout
    • Balance Current Set by External Components
  • Supply Voltage Range from 6 V to 30 V Continuous and 36 V Peak
  • Low Power:
    • Typical 12-µA Sleep, 45-µA Idle
  • Integrated Precision 5-V, 3-mA LDO
  • APPLICATIONS
    • Uninterruptible Power Systems (UPS)
    • E-Bike and E-Scooter
    • Large-Format Battery Systems
    • Electric and Hybrid Electric Vehicles

The bq76PL536 is a stackable three to six series cell lithium-ion battery pack protector and analog front end (AFE) that incorporates a precision analog-to-digital converter (ADC); independent cell voltage and temperature protection; cell balancing, and a precision 5-V regulator to power user circuitry.

The bq76PL536 integrates a voltage translation and precision analog-to-digital converter system to measure battery cell voltages with high accuracy and speed.

The bq76PL536 provides full protection (secondary protection) for overvoltage, undervoltage, and overtemperature conditions. When safety thresholds are exceeded, the bq76PL536 sets the FAULT output. No external components are needed to configure or enable the protection features.

Cell voltage and temperature protection functions are independent of the ADC system. Programmable protection thresholds and detection delay times are stored in Error Check/Correct (ECC) OTP EPROM, which increases the flexibility and reliability of the battery management system.

The bq76PL536 is intended to be used with a host controller to maximize the functionality of the battery management system. However, the protection functions do not require a host controller.

The bq76PL536 can be stacked vertically to monitor up to 192 cells without additional isolation components between ICs. A high-speed serial peripheral interface (SPI) bus operates between each bq76PL536 to provide reliable communications through a high-voltage battery cell stack.

The host microcontroller controls cell balancing of individual cells by setting the registers (via SPI) which control the appropriate CBx outputs. These outputs can be turned off via the same control, or automatically by the internal programmable safety timer. The balancing bypass current is set via an external series resistor and FET.

The bq76PL536 is a stackable three to six series cell lithium-ion battery pack protector and analog front end (AFE) that incorporates a precision analog-to-digital converter (ADC); independent cell voltage and temperature protection; cell balancing, and a precision 5-V regulator to power user circuitry.

The bq76PL536 integrates a voltage translation and precision analog-to-digital converter system to measure battery cell voltages with high accuracy and speed.

The bq76PL536 provides full protection (secondary protection) for overvoltage, undervoltage, and overtemperature conditions. When safety thresholds are exceeded, the bq76PL536 sets the FAULT output. No external components are needed to configure or enable the protection features.

Cell voltage and temperature protection functions are independent of the ADC system. Programmable protection thresholds and detection delay times are stored in Error Check/Correct (ECC) OTP EPROM, which increases the flexibility and reliability of the battery management system.

The bq76PL536 is intended to be used with a host controller to maximize the functionality of the battery management system. However, the protection functions do not require a host controller.

The bq76PL536 can be stacked vertically to monitor up to 192 cells without additional isolation components between ICs. A high-speed serial peripheral interface (SPI) bus operates between each bq76PL536 to provide reliable communications through a high-voltage battery cell stack.

The host microcontroller controls cell balancing of individual cells by setting the registers (via SPI) which control the appropriate CBx outputs. These outputs can be turned off via the same control, or automatically by the internal programmable safety timer. The balancing bypass current is set via an external series resistor and FET.
open-in-new 查找其他 电池监测器和平衡器
下载 观看带字幕的视频 视频

技术文档

star =有关此产品的 TI 精选热门文档
未找到结果。请清除搜索并重试。
查看全部 4
类型 标题 下载最新的英语版本 日期
* 数据表 3 to 6 Series Cell Lithium-Ion Battery Monitor and Secondary Protection IC 数据表 (Rev. A) 2010年 7月 7日
应用手册 bq76PL536/536A/536AQ1 Communication Basics (Rev. B) 2011年 7月 5日
应用手册 Multi-Cell Li-Ion Battery Management System Using MSP430F5529 and bq76PL536 2010年 12月 16日
应用手册 Improving Communications With the bq76PL536 2010年 8月 11日

设计和开发

如需其他信息或资源，请点击以下任一标题进入详情页面查看（如有）。

软件编程工具

BQ76PL536PGM-1-SW — BQ76PL536PGM-1 编程软件

The BQ76PL536PGM-1 tool interfaces with the bq76PL536PGM-1 programming board
查看选项
封装 引脚 下载
HTQFP (PAP) 64 查看选项
应遵守 TI 评估类商品的标准条款与条件。

订购和质量

包含信息：
  • RoHS
  • REACH
  • 器件标识
  • 引脚镀层/焊球材料
  • MSL 等级/回流焊峰值温度
  • MTBF/时基故障估算
  • 材料成分
  • 鉴定摘要
  • 持续可靠性监测
包含信息：
  • 制造厂地点
  • 封装厂地点

支持和培训

视频