返回页首

产品详细信息

参数

Number of series cells 1 Charge current (Max) (A) 1.5 Operating Vin (Max) (V) 16 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (Min) (V) 4.2 Battery charge voltage (Max) (V) 4.2 Absolute Vin (safety rating) (Max) ((V)) 18 Control topology Linear Control interface Standalone (RC-Settable) Features Integrated LDO, Power Path, BAT temp thermistor monitoring (hot/cold profile) Operating Vin (Min) (V) 4.35 Rating Catalog open-in-new 查找其它 电池充电器IC

封装|引脚|尺寸

VQFN (RHL) 20 16 mm² 3.5 x 4.5 VQFN (RHL) 20 16 mm² 4.5 x 3.5 open-in-new 查找其它 电池充电器IC

特性

  • Small 3.5-mm × 4.5-mm QFN Package
  • Designed for Single-Cell Li-Ion- or Li-Polymer-
    Based Portable Applications
  • Integrated Dynamic Power-Path Management (DPPM)
    Feature Allowing the AC Adapter or the USB Port
    to Simultaneously Power the System and Charge
    the Battery
  • Power Supplement Mode Allows Battery to Supplement
    the USB or AC Input Current
  • Autonomous Power Source Selection (AC Adapter
    or USB)
  • Integrated USB Charge Control With Selectable
    100-mA and 500-mA Maximum Input Current Regulation
    Limits
  • Dynamic Total Current Management for USB
  • Supports Up to 2-A Total Current
  • 3.3-V Integrated LDO Output
  • Thermal Regulation for Charge Control
  • Charge Status Outputs for LED or System Interface
    Indicates Charge and Fault Conditions
  • Reverse Current, Short-Circuit, and Thermal
    Protection
  • Power Good (AC Adapter and USB Port Present)
    Status Outputs
  • Charge Voltage Options: 4.1 V, 4.2 V, or 4.36 V
  • APPLICATIONS
    • Smart Phones and PDAs
    • MP3 Players
    • Digital Cameras Handheld Devices
    • Internet Appliances

All other trademarks are the property of their respective owners

open-in-new 查找其它 电池充电器IC

描述

The bqTINY™ III-series of devices are highly integrated Li-ion linear chargers and system power-path management devices targeted at space-limited portable applications. The bqTINY III-series offer integrated USB-port and DC supply (AC adapter), power-path management with autonomous power-source selection, power FETs and current sensors, high accuracy current and voltage regulation, charge status, and charge termination, in a single monolithic device.

The bqTINY III-series powers the system while independently charging the battery. This feature reduces the charge and discharge cycles on the battery, allows for proper charge termination and allows the system to run with an absent or defective battery pack. This feature also allows for the system to instantaneously turn on from an external power source in the case of a deeply discharged battery pack. The IC design is focused on supplying continuous power to the system when available from the AC, USB, or battery sources.

The power select pin, PSEL, defines which input source is to be used first (primary source – AC or USB). If the primary source is not available, then the IC automatically switches over to the other secondary source if available or the battery as the last option. If the PSEL is set low, the USB input is selected first and if not available, the AC line is selected (if available) but programmed to a USB input limiting rate (100 mA/500 mA max). This feature allows the use of one input connector, where the host programs the PSEL pin according to what source is connected (AC adaptor or USB port).

The bq24038 replaces USBPG with pin VBSEL, to enable user selection of the charge voltage. In addition, pin ACPG was modified to PG. PG is active low when either ac power or USB power is detected.

The ISET1 pin programs the battery&3146;s fast charge constant current level with a resistor. During normal AC operation, the input supply provides power to both the OUT (System) and BAT pins. For peak or excessive loads (typically when operating from the USB power, PSEL = Low) that would cause the input source to enter current limit (or Q3 - USB FET limiting current) and its source and system voltage (OUT pin) to drop, the dynamic power-path management (DPPM) feature reduces the charging current attempting to prevent any further drop in system voltage. This feature allows the selection of a lower current rated adaptor based on the average load (ISYS-AVG + IBAT-PGM ) rather than a high peak transient load.

open-in-new 查找其它 电池充电器IC
下载
您可能感兴趣的类似产品
open-in-new 产品比较
与相比较的设备类似但功能不等效:
BQ24072 正在供货 USB 供能的锂离子电池充电器和电源路径管理 IC,Vout 高于 Vbat 200mV | 线性 This product is a single input, 1.5-A, standalone, single-cell Li-Ion battery charger with power path in a 3x3mm package.
LM3658 正在供货 用于便携式应用的双源 USB/AC 锂化学充电器 IC This product is a dual input Li-Ion battery charger in a 3x3mm package.

技术文档

= 特色
未找到结果。请清除搜索,并重试。 查看所有 9
类型 标题 下载最新的英文版本 发布
* 数据表 bq2403x Single-Chip Charge and System Power-path Management IC (bqTINY™) 数据表 2014年 12月 30日
技术文章 When to use rechargeable batteries in small battery applications 2019年 10月 1日
选择指南 电源管理指南 2018 (Rev. K) 2018年 7月 31日
应用手册 Dynamic Power-Path Mgmt & Dynamic Power Mgmt 2018年 5月 1日
技术文章 Should I use a linear charger or a switching charger? 2015年 10月 30日
技术文章 Summertime and the livin' is easy 2014年 6月 20日
用户指南 Power-Path Li-Ion Charger Selection 2008年 10月 17日
应用手册 Host-side gas-gauge-system design considerations for single-cell handheld apps 2007年 10月 12日
用户指南 bq2403x (bqTiny-111) 1.5-A Single-Chip LiIon & Li-Pol Charge Mgmt IC EVM 2006年 12月 11日

设计与开发

有关其他条款或所需资源,请点击下面的任何链接来查看详情页面。

硬件开发

评估板 下载
BQ24032A 评估模块
BQ24032AEVM
document-generic 用户指南
$49.00
说明

The Texas Instruments bq24032AEVM is the evaluation module (EVM) for the bq24032A Single-Chip Charge and Dynamic Power-Path Management IC in 3.5x4.5 mm2 QFN package. The EVM is a complete bq24032A based circuit and provides a convenient method to evaluate the operation and performance of the IC.

The (...)

特性
  • Typical input voltage: 5 V
  • Charge current limit: 2 A
  • Output regulation voltage: 4.2 V
  • OUT pin for AC conditions: regulated to 4.4 V

软件开发

支持软件 下载
温度传感设计软件
TEMPSENSE-SW The TempSense Designer software allows the user to easily design temperature sensing circuits for many of the Texas Instruments battery charger devices. A full listing of the supported devices is included under the "Support" menu in the program. The user can use the thermisters included in the (...)
特性

The program gives the user:

  • Worse-case limits of the resistance
  • Trip voltages
  • Temperatures of the design

CAD/CAE 符号

封装 引脚 下载
VQFN (RHL) 20 视图选项

订购与质量

支持与培训

可获得 TI E2E™ 论坛的工程师技术支持

所有内容均由 TI 和社区网友按“原样”提供,并不构成 TI 规范。参阅使用条款

如果您对质量、包装或订购 TI 产品有疑问,请参阅 TI 支持