ZHCSGV7F July   2017  – January 2024 CDCI6214

PRODUCTION DATA  

  1.   1
  2. 特性
  3. 应用
  4. 说明
  5. Device Comparison
  6. Pin Configuration and Functions
  7. Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  EEPROM Characteristics
    6. 6.6  Reference Input, Single-Ended and Differential Mode Characteristics (REFP, REFN, FB_P, FB_N)
    7. 6.7  Reference Input, Crystal Mode Characteristics (XIN, XOUT)
    8. 6.8  General-Purpose Input and Output Characteristics (GPIO[4:1], SYNC/RESETN)
    9. 6.9  Triple Level Input Characteristics (EEPROMSEL, REFSEL)
    10. 6.10 Reference Mux Characteristics
    11. 6.11 Phase-Locked Loop Characteristics
    12. 6.12 Closed-Loop Output Jitter Characteristics
    13. 6.13 Output Mux Characteristics
    14. 6.14 LVCMOS Output Characteristics
    15. 6.15 HCSL Output Characteristics
    16. 6.16 LVDS DC-Coupled Output Characteristics
    17. 6.17 Programmable Differential AC-Coupled Output Characteristics
    18. 6.18 Output Skew and Delay Characteristics
    19. 6.19 Output Synchronization Characteristics
    20. 6.20 Timing Characteristics
    21. 6.21 I2C-Compatible Serial Interface Characteristics (SDA/GPIO2, SCL/GPIO3)
    22. 6.22 Timing Requirements, I2C-Compatible Serial Interface (SDA/GPIO2, SCL/GPIO3)
    23. 6.23 Power Supply Characteristics
    24. 6.24 Typical Characteristics
  8. Parameter Measurement Information
    1. 7.1 Parameters
      1. 7.1.1 Reference Inputs
      2. 7.1.2 Outputs
      3. 7.1.3 Serial Interface
      4. 7.1.4 Power Supply
  9. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Reference Block
        1. 8.3.1.1 Input Stages
          1. 8.3.1.1.1 Crystal Oscillator
          2. 8.3.1.1.2 LVCMOS
          3. 8.3.1.1.3 Differential AC-Coupled
        2. 8.3.1.2 Reference Mux
        3. 8.3.1.3 Reference Divider
          1. 8.3.1.3.1 Doubler
        4. 8.3.1.4 Bypass-Mux
        5. 8.3.1.5 Zero Delay, Internal and External Path
      2. 8.3.2 Phase-Locked Loop
      3. 8.3.3 Clock Distribution
        1. 8.3.3.1 Output Channel
        2. 8.3.3.2 Divider Glitch-Less Update
      4. 8.3.4 Control Pins
        1. 8.3.4.1 Global and Individual Output Enable: OE and OE_Y[4:1]
      5. 8.3.5 Operation Modes
      6. 8.3.6 Divider Synchronization - SYNC
      7. 8.3.7 EEPROM - Cyclic Redundancy Check
      8. 8.3.8 Power Supplies
        1. 8.3.8.1 Power Management
    4. 8.4 Device Functional Modes
      1. 8.4.1 Pin Mode
      2. 8.4.2 Serial Interface Mode
        1. 8.4.2.1 Fall-Back Mode
    5. 8.5 Programming
      1. 8.5.1 Recommended Programming Procedure
      2. 8.5.2 EEPROM Access
      3. 8.5.3 Device Defaults
  10. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Do's and Don'ts
    4. 9.4 Initialization Setup
    5. 9.5 Power Supply Recommendations
      1. 9.5.1 Power-Up Sequence
      2. 9.5.2 De-Coupling
    6. 9.6 Layout
      1. 9.6.1 Layout Guidelines
      2. 9.6.2 Layout Examples
  11. 10Register Maps
    1. 10.1 CDCI6214 Registers
    2. 10.2 EEPROM Map
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Development Support
      2. 11.1.2 Device Nomenclature
    2. 11.2 接收文档更新通知
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 静电放电警告
    6. 11.6 术语表
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

Phase-Locked Loop

The CDCI6214 contains a fully integrated phase-locked loop circuit. The error between a reference phase and an internal feedback phase is compared at the phase-frequency-detector. The comparison result is fed to a charge pump that is connected to an integrated loop filter. The control voltage resulting from the loop filter tunes an internal voltage-controlled oscillator (VCO). The frequency of the VCO is fed through a pre-scaler feedback divider (PSFB) and another feedback divider back to the PFD.

The PLL closed-loop bandwidth is configurable using registers PLL0, PLL1, and PLL2.

  • Integer PLL
  • PFD operates 1 MHz to 100 MHz
  • Live Lock-Detector provides PLL lock status on status pin and bit lock_det (there is an additional sticky bit unlock_s)
  • Integrated selectable loop filter components
  • For 25-MHz PFD bandwidths between 100 kHz and 3000 kHz can be achieved to optimize PLL to input reference
  • Voltage-Controlled Oscillator (VCO) tuning range of 2400 to 2800 MHz
  • VCO is compatible to 0.5% spread spectrum (SSC) references at 100 MHz.

GUID-4568586B-5CE0-4536-8B6F-5ABF600214DF-low.gifFigure 8-3 Phase-Locked Loop Circuit
Table 8-2 Common Clock Generator Loop Filter Settings
fVCO in MHz(1)fPFD in MHzBW in MHzPhase Margin in °Damping FactorICP in mACPcap IN pFRRes IN kΩCZcap IN pF
pll_cp_up(2)pll_lf_pcappll_lf_respll_lf_zcap
2400250.51670.92.017.52.5450
2400500.97671.32.017.52.5450
24001001.41681.22.417.51.5450
2457.661.441.04671.41.817.52.5450
2500250.49670.92.017.52.5450
2500500.93681.32.017.52.5450
2680670.38671.30.219.55.5480
2688480.93681.31.517.52.5480
2688960.36671.00.219.53.5480
2800501.00681.02.617.51.5450
28001001.00681.01.317.51.5450
All values typical design targets.
Program same value to pll_cp_dn.