ZHCS158C July   2012  – January 2017 ADS1299 , ADS1299-4 , ADS1299-6

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
  4. 修订历史记录
  5. Device Comparison
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements: Serial Interface
    7. 7.7 Switching Characteristics: Serial Interface
    8. 7.8 Typical Characteristics
  8. Parametric Measurement Information
    1. 8.1 Noise Measurements
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Analog Functionality
        1. 9.3.1.1 Input Multiplexer
          1. 9.3.1.1.1 Device Noise Measurements
          2. 9.3.1.1.2 Test Signals (TestP and TestN)
          3. 9.3.1.1.3 Temperature Sensor (TempP, TempN)
          4. 9.3.1.1.4 Supply Measurements (MVDDP, MVDDN)
          5. 9.3.1.1.5 Lead-Off Excitation Signals (LoffP, LoffN)
          6. 9.3.1.1.6 Auxiliary Single-Ended Input
        2. 9.3.1.2 Analog Input
        3. 9.3.1.3 PGA Settings and Input Range
          1. 9.3.1.3.1 Input Common-Mode Range
          2. 9.3.1.3.2 Input Differential Dynamic Range
          3. 9.3.1.3.3 ADC ΔΣ Modulator
          4. 9.3.1.3.4 Reference
      2. 9.3.2 Digital Functionality
        1. 9.3.2.1 Digital Decimation Filter
          1. 9.3.2.1.1 Sinc Filter Stage (sinx / x)
        2. 9.3.2.2 Clock
        3. 9.3.2.3 GPIO
        4. 9.3.2.4 ECG and EEG Specific Features
          1. 9.3.2.4.1 Input Multiplexer (Rerouting the BIAS Drive Signal)
          2. 9.3.2.4.2 Input Multiplexer (Measuring the BIAS Drive Signal)
          3. 9.3.2.4.3 Lead-Off Detection
            1. 9.3.2.4.3.1 DC Lead-Off
            2. 9.3.2.4.3.2 AC Lead-Off (One Time or Periodic)
          4. 9.3.2.4.4 Bias Lead-Off
          5. 9.3.2.4.5 Bias Drive (DC Bias Circuit)
            1. 9.3.2.4.5.1 Bias Configuration with Multiple Devices
    4. 9.4 Device Functional Modes
      1. 9.4.1 Start
        1. 9.4.1.1 Settling Time
      2. 9.4.2 Reset (RESET)
      3. 9.4.3 Power-Down (PWDN)
      4. 9.4.4 Data Retrieval
        1. 9.4.4.1 Data Ready (DRDY)
        2. 9.4.4.2 Reading Back Data
      5. 9.4.5 Continuous Conversion Mode
      6. 9.4.6 Single-Shot Mode
    5. 9.5 Programming
      1. 9.5.1 Data Format
      2. 9.5.2 SPI Interface
        1. 9.5.2.1 Chip Select (CS)
        2. 9.5.2.2 Serial Clock (SCLK)
        3. 9.5.2.3 Data Input (DIN)
        4. 9.5.2.4 Data Output (DOUT)
      3. 9.5.3 SPI Command Definitions
        1. 9.5.3.1  Sending Multi-Byte Commands
        2. 9.5.3.2  WAKEUP: Exit STANDBY Mode
        3. 9.5.3.3  STANDBY: Enter STANDBY Mode
        4. 9.5.3.4  RESET: Reset Registers to Default Values
        5. 9.5.3.5  START: Start Conversions
        6. 9.5.3.6  STOP: Stop Conversions
        7. 9.5.3.7  RDATAC: Read Data Continuous
        8. 9.5.3.8  SDATAC: Stop Read Data Continuous
        9. 9.5.3.9  RDATA: Read Data
        10. 9.5.3.10 RREG: Read From Register
        11. 9.5.3.11 WREG: Write to Register
    6. 9.6 Register Maps
      1. 9.6.1 User Register Description
        1. 9.6.1.1  ID: ID Control Register (address = 00h) (reset = xxh)
        2. 9.6.1.2  CONFIG1: Configuration Register 1 (address = 01h) (reset = 96h)
        3. 9.6.1.3  CONFIG2: Configuration Register 2 (address = 02h) (reset = C0h)
        4. 9.6.1.4  CONFIG3: Configuration Register 3 (address = 03h) (reset = 60h)
        5. 9.6.1.5  LOFF: Lead-Off Control Register (address = 04h) (reset = 00h)
        6. 9.6.1.6  CHnSET: Individual Channel Settings (n = 1 to 8) (address = 05h to 0Ch) (reset = 61h)
        7. 9.6.1.7  BIAS_SENSP: Bias Drive Positive Derivation Register (address = 0Dh) (reset = 00h)
        8. 9.6.1.8  BIAS_SENSN: Bias Drive Negative Derivation Register (address = 0Eh) (reset = 00h)
        9. 9.6.1.9  LOFF_SENSP: Positive Signal Lead-Off Detection Register (address = 0Fh) (reset = 00h)
        10. 9.6.1.10 LOFF_SENSN: Negative Signal Lead-Off Detection Register (address = 10h) (reset = 00h)
        11. 9.6.1.11 LOFF_FLIP: Lead-Off Flip Register (address = 11h) (reset = 00h)
        12. 9.6.1.12 LOFF_STATP: Lead-Off Positive Signal Status Register (address = 12h) (reset = 00h)
        13. 9.6.1.13 LOFF_STATN: Lead-Off Negative Signal Status Register (address = 13h) (reset = 00h)
        14. 9.6.1.14 GPIO: General-Purpose I/O Register (address = 14h) (reset = 0Fh)
        15. 9.6.1.15 MISC1: Miscellaneous 1 Register (address = 15h) (reset = 00h)
        16. 9.6.1.16 MISC2: Miscellaneous 2 (address = 16h) (reset = 00h)
        17. 9.6.1.17 CONFIG4: Configuration Register 4 (address = 17h) (reset = 00h)
  10. 10Applications and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Unused Inputs and Outputs
      2. 10.1.2 Setting the Device for Basic Data Capture
        1. 10.1.2.1 Lead-Off
        2. 10.1.2.2 Bias Drive
      3. 10.1.3 Establishing the Input Common-Mode
      4. 10.1.4 Multiple Device Configuration
        1. 10.1.4.1 Cascaded Mode
        2. 10.1.4.2 Daisy-Chain Mode
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
    1. 11.1 Power-Up Sequencing
    2. 11.2 Connecting the Device to Unipolar (5 V and 3.3 V) Supplies
    3. 11.3 Connecting the Device to Bipolar (±2.5 V and 3.3 V) Supplies
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13器件和文档支持
    1. 13.1 文档支持
      1. 13.1.1 相关文档 
    2. 13.2 相关链接
    3. 13.3 接收文档更新通知
    4. 13.4 社区资源
    5. 13.5 商标
    6. 13.6 静电放电警告
    7. 13.7 Glossary
  14. 14机械、封装和可订购信息

Specifications

Absolute Maximum Ratings(1)

MIN MAX UNIT
Voltage AVDD to AVSS –0.3 5.5 V
DVDD to DGND –0.3 3.9
AVSS to DGND –3 0.2
VREFP to AVSS –0.3 AVDD + 0.3
VREFN to AVSS –0.3 AVDD + 0.3
Analog input AVSS – 0.3 AVDD + 0.3
Digital input DGND – 0.3 DVDD + 0.3
Current Input, continuous, any pin except power supply pins(2) –10 10 mA
Temperature Junction, TJ 150 °C
Storage, Tstg –60 150
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Input pins are diode-clamped to the power-supply rails. Limit the input current to 10 mA or less if the analog input voltage exceeds AVDD + 0.3 V or is less than AVSS – 0.3 V, or if the digital input voltage exceeds DVDD + 0.3 V or is less than DGND – 0.3 V.

ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±1000 V
Charged-device model (CDM), per JEDEC specification JESD22-C101(2) ±500
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

Recommended Operating Conditions

over operating ambient temperature range (unless otherwise noted)
MIN NOM MAX UNIT
POWER SUPPLY
Analog power supply AVDD to AVSS 4.75 5 5.25 V
Digital power supply DVDD to DGND 1.8 1.8 3.6 V
Analog to Digital supply AVDD – DVDD –2.1 3.6 V
ANALOG INPUTS
Full-scale differential input voltage VINxP – VINxN ±VREF / gain V
VCM Input common-mode range (VINxP + VINxN) / 2 See the Input Common-Mode Range subsection of the PGA Settings and Input Range section
VOLTAGE REFERENCE INPUTS
VREF Reference input voltage VREF = (VVREFP – VVREFN) 4.5 V
VREFN Negative input AVSS V
VREFP Positive input AVSS + 4.5 V
CLOCK INPUT
fCLK External clock input frequency CLKSEL pin = 0 1.5 2.048 2.25 MHz
DIGITAL INPUTS
Input voltage DGND – 0.1 DVDD + 0.1 V
TEMPERATURE RANGE
TA Operating temperature range –40 85 °C

Thermal Information

THERMAL METRIC(1) ADS1299-4, ADS1299-6, ADS1299 UNIT
PAG (TQFP)
64 PINS
RθJA Junction-to-ambient thermal resistance 46.2 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 5.8 °C/W
RθJB Junction-to-board thermal resistance 19.6 °C/W
ψJT Junction-to-top characterization parameter 0.2 °C/W
ψJB Junction-to-board characterization parameter 19.2 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance n/a °C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.

Electrical Characteristics

Minimum and maximum specifications apply from TA = –40°C to 85°C. Typical specifications are at TA = +25°C. All specifications are at AVDD – AVSS = 5 V, DVDD = 3.3 V, VREF = 4.5 V, external fCLK = 2.048 MHz, data rate = 250 SPS, and gain = 12 (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
ANALOG INPUTS
Input capacitance 20 pF
Input bias current TA = +25°C, InxP and INxN = 2.5 V ±300 pA
TA = –40°C to +85°C, InxP and INxN = 2.5 V ±300
DC input impedance No lead-off 1000
Current source lead-off detection
(ILEADOFF = 6 nA)
500
PGA PERFORMANCE
Gain settings 1, 2, 4, 6, 8, 12, 24
BW Bandwidth See Table 5
ADC PERFORMANCE
Resolution 24 Bits
DR Data rate fCLK = 2.048 MHz 250 16000 SPS
DC CHANNEL PERFORMANCE
Input-referred noise (0.01 Hz to 70 Hz) 10 seconds of data, gain = 24(1) 1 μVPP
250 points, 1 second of data, gain = 24, TA = +25°C 1 1.35
250 points, 1 second of data, gain = 24, TA = –40°C to +85°C 1 1.6
All other sample rates and gain settings See Noise Measurements
INL Integral nonlinearity Full-scale with gain = 12, best fit 8 ppm
Offset error 60 μV
Offset error drift 80 nV/°C
Gain error Excluding voltage reference error 0.1 ±0.5 % of FS
Gain drift Excluding voltage reference drift 3 ppm/°C
Gain match between channels 0.2 % of FS
AC CHANNEL PERFORMANCE
CMRR Common-mode rejection ratio fCM = 50 Hz and 60 Hz(2) –110 –120 dB
PSRR Power-supply rejection ratio fPS = 50 Hz and 60 Hz 96 dB
Crosstalk fIN = 50 Hz and 60 Hz –110 dB
SNR Signal-to-noise ratio VIN = –2 dBFs, fIN = 10-Hz input, gain = 12 121 dB
THD Total harmonic distortion VIN = –0.5 dBFs, fIN = 10 Hz –99 dB
PATIENT BIAS AMPLIFIER
Integrated noise BW = 150 Hz 2 μVRMS
Gain bandwidth product 50-kΩ || 10-pF load, gain = 1 100 kHz
Slew rate 50-kΩ || 10-pF load, gain = 1 0.07 V/μs
THD Total harmonic distortion fIN = 10 Hz, gain = 1 –80 dB
Common-mode input range AVSS + 0.3 AVDD – 0.3 V
Short-circuit current 1.1 mA
Quiescent power consumption 20 μA
LEAD-OFF DETECT
Frequency Continuous At dc, fDR / 4,
see Register Maps for settings
Hz
One time or periodic 7.8, 31.2
Current ILEAD_OFF[1:0] = 00 6 nA
ILEAD_OFF[1:0] = 01 24
ILEAD_OFF[1:0] = 10 6 μA
ILEAD_OFF[1:0] = 11 24
Current accuracy ±20%
Comparator threshold accuracy ±30 mV
EXTERNAL REFERENCE
Input impedance 5.6
INTERNAL REFERENCE
VREF Internal reference voltage 4.5 V
VREF accuracy ±0.2%
Drift TA = –40°C to +85°C 35 ppm/°C
Start-up time 150 ms
SYSTEM MONITORS
Reading error Analog supply 2%
Digital supply 2%
Device wake up From power-up to DRDY low 150 ms
STANDBY mode 31.25 µs
Temperature sensor reading Voltage TA = +25°C 145 mV
Coefficient 490 μV/°C
Test signal Signal frequency See Register Maps section for settings fCLK / 221, fCLK / 220 Hz
Signal voltage See Register Maps section for settings ±1, ±2 mV
Accuracy ±2%
CLOCK
Internal oscillator clock frequency Nominal frequency 2.048 MHz
Internal clock accuracy TA = +25°C ±0.5%
TA = –40°C to +85°C ±2.5%
Internal oscillator start-up time 20 μs
Internal oscillator power consumption 120 μW
DIGITAL INPUT/OUTPUT (DVDD = 1.8 V to 3.6 V)
VIH High-level input voltage 0.8 DVDD DVDD + 0.1 V
VIL Low-level input voltage –0.1 0.2 DVDD V
VOH High-level output voltage IOH = –500 μA 0.9 DVDD V
VOL Low-level output voltage IOL = +500 μA 0.1 DVDD V
Input current 0 V < VDigitalInput < DVDD –10 10 μA
SUPPLY CURRENT (Bias Turned Off)
IAVDD AVDD current ADS1299-4 Normal mode, AVDD – AVSS = 5 V 4.06 mA
ADS1299-6 5.57
ADS1299 7.14
IDVDD DVDD current ADS1299-4 Normal mode, DVDD = 3.3 V 0.54 mA
ADS1299-6 0.66
ADS1299 1
ADS1299-4 Normal mode, DVDD = 1.8 V 0.27
ADS1299-6 0.34
ADS1299 0.5
POWER DISSIPATION (Analog Supply = 5 V, Bias Amplifiers Turned Off)
Power dissipation ADS1299-4 Normal mode 22 24 mW
Power-down 10 µW
Standby mode, internal reference 5.1 mW
ADS1299-6 Normal mode 30 33 mW
Power-down 10 µW
Standby mode, internal reference 5.1 mW
ADS1299 Normal mode 39 42 mW
Power-down 10 µW
Standby mode, internal reference 5.1 mW
Noise data measured in a 10-second interval. Test not performed in production. Input-referred noise is calculated with the input shorted (without electrode resistance) over a 10-second interval.
CMRR is measured with a common-mode signal of AVSS + 0.3 V to AVDD – 0.3 V. The values indicated are the minimum of the eight channels.

Timing Requirements: Serial Interface

over operating ambient temperature range (unless otherwise noted)
2.7 V ≤ DVDD ≤ 3.6 V 1.8 V ≤ DVDD ≤ 2.0 V UNIT
MIN MAX MIN MAX
tCLK Master clock period 414 666 414 666 ns
tCSSC Delay time, CS low to first SCLK 6 17 ns
tSCLK SCLK period 50 66.6 ns
tSPWH, L Pulse duration, SCLK pulse duration, high or low 15 25 ns
tDIST Setup time, DIN valid to SCLK falling edge 10 10 ns
tDIHD Hold time, valid DIN after SCLK falling edge 10 11 ns
tCSH Pulse duration, CS high 2 2 tCLK
tSCCS Delay time, final SCLK falling edge to CS high 4 4 tCLK
tSDECODE Command decode time 4 4 tCLK
tDISCK2ST Setup time, DAISY_IN valid to SCLK rising edge 10 10 ns
tDISCK2HT Hold time, DAISY_IN valid after SCLK rising edge 10 10 ns

Switching Characteristics: Serial Interface

over operating ambient temperature range (unless otherwise noted)
PARAMETER 2.7 V ≤ DVDD ≤ 3.6 V 1.8 V ≤ DVDD ≤ 2.0 V UNIT
MIN MAX MIN MAX
tDOHD Hold time, SCLK falling edge to invalid DOUT 10 10 ns
tDOPD Propagation delay time, SCLK rising edge to DOUT valid 17 32 ns
tCSDOD Propagation delay time, CS low to DOUT driven 10 20 ns
tCSDOZ Propagation delay time, CS high to DOUT Hi-Z 10 20 ns
ADS1299 ADS1299-4 ADS1299-6 tim_serial_bas459.gif

NOTE:

SPI settings are CPOL = 0 and CPHA = 1.
Figure 1. Serial Interface Timing
ADS1299 ADS1299-4 ADS1299-6 tim_daisy_bas499.gif Figure 2. Daisy-Chain Interface Timing

Typical Characteristics

At TA = 25°C, AVDD = 5 V, AVSS = 0 V, DVDD = 3.3 V, internal VREFP = 4.5 V, VREFN = AVSS, external clock = 2.048 MHz, data rate = 250 SPS, and gain = 12 (unless otherwise noted)
ADS1299 ADS1299-4 ADS1299-6 G003_SBAS499.png
Figure 3. Input-Referred Noise
ADS1299 ADS1299-4 ADS1299-6 G005_SBAS499.png
Figure 5. Common-Mode Rejection Ratio vs Frequency
ADS1299 ADS1299-4 ADS1299-6 G007_SBAS499.png
Figure 7. Leakage Current vs Temperature
ADS1299 ADS1299-4 ADS1299-6 G009_SBAS499.png
Figure 9. THD vs Frequency
ADS1299 ADS1299-4 ADS1299-6 G011_SBAS499.png
Figure 11. INL vs Temperature
ADS1299 ADS1299-4 ADS1299-6 G013_SBAS499.png
Figure 13. FFT Plot (60-Hz Signal)
ADS1299 ADS1299-4 ADS1299-6 G015_SBAS499.gif
Figure 15. Test Signal Amplitude Accuracy
ADS1299 ADS1299-4 ADS1299-6 G017_SBAS499.png
Figure 17. Lead-Off Current Source Accuracy Distribution
ADS1299 ADS1299-4 ADS1299-6 G004_SBAS499.png
Figure 4. Noise Histogram
ADS1299 ADS1299-4 ADS1299-6 G006_SBAS499.png
Figure 6. Leakage Current vs Input Voltage
ADS1299 ADS1299-4 ADS1299-6 G008_SBAS499.png
Figure 8. PSRR vs Frequency
ADS1299 ADS1299-4 ADS1299-6 G010_SBAS499.png
Figure 10. INL vs PGA Gain
ADS1299 ADS1299-4 ADS1299-6 G012_SBAS499.png
Figure 12. THD FFT Plot (60-Hz Signal)
ADS1299 ADS1299-4 ADS1299-6 G014_SBAS499.png
Figure 14. Offset vs PGA Gain (Absolute Value)
ADS1299 ADS1299-4 ADS1299-6 G016_SBAS499.gif
Figure 16. Lead-Off Comparator Threshold Accuracy