ZHCSI97F May   2010  – March 2020 TPS7A65-Q1

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     Device Images
      1.      典型应用电路原理图
      2.      典型稳压器稳定性
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Dissipation Ratings
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Power Up
      2. 7.3.2 Charge-Pump Operation
      3. 7.3.3 Low-Power Mode
      4. 7.3.4 Undervoltage Shutdown
      5. 7.3.5 Low-Voltage Tracking
      6. 7.3.6 Integrated Fault Protection
      7. 7.3.7 Thermal Shutdown
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation With VIN Lower Than 4 V
      2. 7.4.2 Operation With VIN Larger Than 4 V
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curve
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 Power Dissipation and Thermal Considerations
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 接收文档更新通知
    2. 11.2 社区资源
    3. 11.3 商标
    4. 11.4 静电放电警告
    5. 11.5 Glossary
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.5 Electrical Characteristics

VIN = 14 V, TJ = –40ºC to +150ºC (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
INPUT VOLTAGE (VIN Pin)
VIN Input voltage Fixed 5-V output, IOUT = 1 mA 7(1) 40 V
Fixed 3.3-V output, IOUT = 1 mA 7(1) 40
IQUIESCENT Quiescent current VIN = 8.2 V to 18 V, IOUT = 0.01 mA to 0.75 mA 25 40 µA
VIN-UVLO Undervoltage lockout voltage Ramp VIN down until output is turned OFF 3.16 V
VIN(POWERUP) Power-up voltage Ramp VIN up until output is turned ON 3.45 V
REGULATED OUTPUT VOLTAGE (VOUT Pin)
VOUT Regulated output voltage Fixed VOUT value (3.3 V or 5 V as applicable),
IOUT = 10 mA, 10 mA to 300 mA,
VIN = VOUT + 1 V to 16 V		 –2% 2%
∆VLINE-REG Line regulation VIN = 6 V to 28 V, IOUT = 10 mA, VOUT = 5 V 15 mV
VIN = 6 V to 28 V, IOUT = 10 mA, VOUT = 3.3 V 20
∆VLOAD-REG Load regulation IOUT = 10 mA to 300 mA, VIN= 14 V, VOUT = 5 V 25 mV
IOUT = 10 mA to 300 mA, VIN = 14 V, VOUT = 3.3 V 35
VDROPOUT(2) Dropout voltage
(VIN – VOUT)		 IOUT = 250 mA 500 mV
IOUT = 150 mA 300
RSW(3) Switch resistance VIN to VOUT resistance 2 Ω
IOUT Output current VOUT in regulation 0 300 mA
ICL Output current limit VOUT = 0 V (VOUT pin is shorted to ground) 350 1000 mA
PSRR(3) Power-supply ripple rejection VIN-RIPPLE = 0.5 Vpp, IOUT = 300 mA,
frequency = 100 Hz, VOUT = 5 V, VOUT = 3.3 V		 60 dB
VIN-RIPPLE = 0.5 Vpp, IOUT = 300 mA,
frequency = 150 kHz, VOUT = 5 V, VOUT = 3.3 V		 30
TEMPERATURE
TSHUTDOWN Thermal shutdown trip point 165 ºC
THYST Thermal shutdown hysteresis 10 ºC
(1) VIN can go down to 4 V for 130 ms or less and remain functional. If VIN is less than 7 V for longer than 130 ms, then some devices may turn off until the input voltage rises above 7 V.
(2) This test is done with VOUT in regulation and VIN – VOUT parameter is measured when VOUT (3.3 V or 5 V) drops by 100 mV at specified loads.
(3) Specified by design; not tested.