ZHCSG94L August   2013  – February 2019 TPS659038-Q1 , TPS659039-Q1

PRODUCTION DATA.  

  1. 1 器件概要
    1. 1.1 特性
    2. 1.2 应用
    3. 1.3 描述
    4. 1.4 简化方框图
  2. 2 修订历史记录
  3. 3 Device Comparison
  4. 4 Pin Configuration and Functions
    1. 4.1 Pin Functions
      1.      Pin Functions
    2. 4.2 Device Ball Mapping – 13 × 13 nFBGA, 169 Balls, 0,8-mm Pitch
    3. 4.3 Signal Descriptions
  5. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: Latch Up Rating
    6. 5.6  Electrical Characteristics: LDO Regulator
    7. 5.7  Electrical Characteristics: Dual-Phase (SMPS12 and SMPS45) and Triple-Phase (SMPS123 and SMPS457) Regulators
    8. 5.8  Electrical Characteristics: Stand-Alone Regulators (SMPS3, SMPS6, SMPS7, SMPS8, and SMPS9)
    9. 5.9  Electrical Characteristics: Reference Generator (Bandgap)
    10. 5.10 Electrical Characteristics: 16-MHz Crystal Oscillator, 32-kHz RC Oscillator, and Output Buffers
    11. 5.11 Electrical Characteristics: DC-DC Clock Sync
    12. 5.12 Electrical Characteristics: 12-Bit Sigma-Delta ADC
    13. 5.13 Electrical Characteristics: Thermal Monitoring and Shutdown
    14. 5.14 Electrical Characteristics: System Control Thresholds
    15. 5.15 Electrical Characteristics: Current Consumption
    16. 5.16 Electrical Characteristics: Digital Input Signal Parameters
    17. 5.17 Electrical Characteristics: Digital Output Signal Parameters
    18. 5.18 Electrical Characteristics: I/O Pullup and Pulldown Resistance
    19. 5.19 I2C Interface Timing Requirements
    20. 5.20 SPI Timing Requirements
    21. 5.21 Typical Characteristics
  6. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagrams
    3. 6.3 Feature Description
      1. 6.3.1  Power Management
      2. 6.3.2  Power Resources (Step-Down and Step-Up SMPS Regulators, LDOs)
        1. 6.3.2.1 Step-Down Regulators
          1. 6.3.2.1.1 Sync Clock Functionality
          2. 6.3.2.1.2 Output Voltage and Mode Selection
          3. 6.3.2.1.3 Current Monitoring and Short Circuit Detection
          4. 6.3.2.1.4 POWERGOOD
          5. 6.3.2.1.5 DVS-Capable Regulators
          6. 6.3.2.1.6 Non DVS-Capable Regulators
          7. 6.3.2.1.7 Step-Down Converters SMPS12 and SMPS123
            1.         a. Dual-Phase SMPS and Stand-Alone SMPS
            2.         b. Triple Phase SMPS
          8. 6.3.2.1.8 Step-Down Converter SMPS45 and SMPS457
          9. 6.3.2.1.9 Step-Down Converters SMPS3, SMPS6, SMPS7, SMPS8, and SMPS9
        2. 6.3.2.2 LDOs – Low Dropout Regulators
          1. 6.3.2.2.1 LDOVANA
          2. 6.3.2.2.2 LDOVRTC
          3. 6.3.2.2.3 LDO Bypass (LDO9)
          4. 6.3.2.2.4 LDOUSB
          5. 6.3.2.2.5 Other LDOs
      3. 6.3.3  Long-Press Key Detection
      4. 6.3.4  RTC
        1. 6.3.4.1 General Description
        2. 6.3.4.2 Time Calendar Registers
          1. 6.3.4.2.1 TC Registers Read Access
          2. 6.3.4.2.2 TC Registers Write Access
        3. 6.3.4.3 RTC Alarm
        4. 6.3.4.4 RTC Interrupts
        5. 6.3.4.5 RTC 32-kHz Oscillator Drift Compensation
      5. 6.3.5  GPADC – 12-Bit Sigma-Delta ADC
        1. 6.3.5.1 Asynchronous Conversion Request (SW)
        2. 6.3.5.2 Periodic Conversion Request (AUTO)
        3. 6.3.5.3 Calibration
      6. 6.3.6  General-Purpose I/Os (GPIO Terminals)
        1. 6.3.6.1 REGEN Output
      7. 6.3.7  Thermal Monitoring
        1. 6.3.7.1 Hot-Die Function (HD)
        2. 6.3.7.2 Thermal Shutdown (TS)
        3. 6.3.7.3 Temperature Monitoring With External NTC Resistor or Diode
      8. 6.3.8  Interrupts
      9. 6.3.9  Control Interfaces
        1. 6.3.9.1 I2C Interfaces
          1. 6.3.9.1.1 I2C Implementation
          2. 6.3.9.1.2 F/S Mode Protocol
          3. 6.3.9.1.3 HS Mode Protocol
        2. 6.3.9.2 SPI Interface
          1. 6.3.9.2.1 SPI Modes
          2. 6.3.9.2.2 SPI Protocol
      10. 6.3.10 Device Identification
    4. 6.4 Device Functional Modes
      1. 6.4.1  Embedded Power Controller
      2. 6.4.2  State Transition Requests
        1. 6.4.2.1 ON Requests
        2. 6.4.2.2 OFF Requests
        3. 6.4.2.3 SLEEP and WAKE Requests
      3. 6.4.3  Power Sequences
      4. 6.4.4  Start Up Timing and RESET_OUT Generation
      5. 6.4.5  Power On Acknowledge
        1. 6.4.5.1 POWERHOLD Mode
        2. 6.4.5.2 AUTODEVON Mode
      6. 6.4.6  BOOT Configuration
        1. 6.4.6.1 Boot Terminal Selection
      7. 6.4.7  Reset Levels
      8. 6.4.8  Warm Reset
      9. 6.4.9  RESET_IN
      10. 6.4.10 Watchdog Timer (WDT)
      11. 6.4.11 System Voltage Monitoring
        1. 6.4.11.1 Generating a POR
  7. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1  Recommended External Components
        2. 7.2.2.2  SMPS Input Capacitors
        3. 7.2.2.3  SMPS Output Capacitors
        4. 7.2.2.4  SMPS Inductors
        5. 7.2.2.5  LDO Input Capacitors
        6. 7.2.2.6  LDO Output Capacitors
        7. 7.2.2.7  VCC1
          1. 7.2.2.7.1 Meeting the Power Down Sequence
          2. 7.2.2.7.2 Maintaining Sufficient Input Voltage
        8. 7.2.2.8  VIO_IN
        9. 7.2.2.9  16-MHz Crystal
        10. 7.2.2.10 GPADC
      3. 7.2.3 Application Curves
  8. 8 Power Supply Recommendations
  9. 9 Layout
    1. 9.1 Layout Guidelines
    2. 9.2 Layout Example
  10. 10器件和文档支持
    1. 10.1 器件支持
      1. 10.1.1 第三方产品免责声明
      2. 10.1.2 器件命名规则
    2. 10.2 文档支持
      1. 10.2.1 相关文档
    3. 10.3 相关链接
    4. 10.4 接收文档更新通知
    5. 10.5 社区资源
    6. 10.6 商标
    7. 10.7 静电放电警告
    8. 10.8 Glossary
  11. 11机械、封装和可订购信息
    1. 11.1 封装材料信息

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • ZWS|169
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.1 Absolute Maximum Ratings

See(1)(2).
MIN MAX UNIT
Voltage Voltage on VCC1 pins –0.3 6 V
Voltage on VCC_SENSE, VCC_SENSE2 pins –0.3 7 V
All LDOs and SMPS supply voltage input pins (except LDOUSB_IN2) –0.3 6 V
Voltage on SMPSx_SW pins, 10 ns transient –2 7 V
All SMPS-related input pins _FDBK –0.3 3.6 V
LDOUSB regulator LDOUSB_IN2 input voltage –0.3 20 V
I/O digital supply voltage (VIO_IN with respect to VIO_GND) –0.3 VIOmax + 0.3 VIOmax + 0.3 V
VBUS –2 20 V
Voltage on the GPADC pins: GPADC_IN0, GPADC_IN1 –0.3 5.25 V
Voltage on the GPADC pins: GPADC_IN2 –0.3 2.5 V
OTP supply voltage VPROG –0.3 20 V
Voltage on VRTC digital input pins Without fail-safe –0.3 2.15 V
With fail-safe –0.3 5.25
Voltage on VIO digital input pins (VIO_IN pin reference) –0.3 VIOmax + 0.3 V
Voltage on VSYS digital input pins (VCC1 pin reference) –0.3 6 V
Current Peak output current on all pins other than power resources –5 5 mA
Power pins, nFBGA 1 A
Buck SMPS, SMPSx_IN, SMPSx_SW, and SMPSx_OUT total per phase 4 A
LDOs 1 A
Junction temperature range, TJ –45 150 °C
Storage temperature, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum conditions for extended periods may affect device reliability.
(2) When operating the TPS659038-Q1 andTPS659039-Q1 devices without an external crystal, each SMPS regulating an output voltage greater than 1.8 V must be disabled before VCC is removed. Lowering VCC below the programmed VSYS_LO level while any SMPS is regulating an output voltage above 1.8 V may cause damage to the device.