ZHCS127D March   2011  – March 2015 TPS24720

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 典型应用 (12V/10A)
  5. 5 修订历史记录
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 THERMAL INFORMATION
    4. 7.4 Recommended Operating Conditions
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Detailed Pin Descriptions
        1. 8.3.1.1  EN
        2. 8.3.1.2  ENSD
        3. 8.3.1.3  FFLTb
        4. 8.3.1.4  FLTb
        5. 8.3.1.5  GATE
        6. 8.3.1.6  GND
        7. 8.3.1.7  IMON
        8. 8.3.1.8  LATCH
        9. 8.3.1.9  OUT
        10. 8.3.1.10 OV
        11. 8.3.1.11 PGb
        12. 8.3.1.12 PROG
        13. 8.3.1.13 SENSE
        14. 8.3.1.14 SET
        15. 8.3.1.15 TIMER
        16. 8.3.1.16 VCC
    4. 8.4 Device Functional Modes
      1. 8.4.1  Board Plug-In
      2. 8.4.2  Inrush Operation
      3. 8.4.3  Action of the Constant-Power Engine
      4. 8.4.4  Circuit Breaker and Fast Trip
      5. 8.4.5  Automatic Restart
      6. 8.4.6  PGb, FLTb, and Timer Operations
      7. 8.4.7  Overtemperature Shutdown
      8. 8.4.8  Start-Up of Hot-Swap Circuit by VCC or EN
      9. 8.4.9  Minimization of Power Dissipation at STANDY by ENSD
      10. 8.4.10 Fault Detection of MOSFET Short With FFLTb
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Power-Limited Start-Up
          1. 9.2.2.1.1 STEP 1. Choose RSENSE, RSET, and RIMON
          2. 9.2.2.1.2 STEP 2. Choose MOSFET M1
          3. 9.2.2.1.3 STEP 3. Choose Power-Limit Value, PLIM, and RPROG
          4. 9.2.2.1.4 STEP 4. Choose Output Voltage Rising Time, tON, and Timing Capacitor CT
          5. 9.2.2.1.5 STEP 5. Calculate the Retry-Mode Duty Ratio
          6. 9.2.2.1.6 STEP 6. Select R1, R2, and R3 for UV and OV
          7. 9.2.2.1.7 STEP 7. Choose RGATE, R4, R5, R6, and C1
        2. 9.2.2.2 Additional Design Considerations
          1. 9.2.2.2.1 Use of PGb
          2. 9.2.2.2.2 Output Clamp Diode
          3. 9.2.2.2.3 Gate Clamp Diode
          4. 9.2.2.2.4 High-Gate-Capacitance Applications
          5. 9.2.2.2.5 Bypass Capacitors
          6. 9.2.2.2.6 Output Short-Circuit Measurements
      3. 9.2.3 Application Curve
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 文档支持
    2. 12.2 商标
    3. 12.3 静电放电警告
    4. 12.4 术语表
  13. 13机械封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Pin Configuration and Functions

RGT Package
16 Pins
Top View
TPS24720 po_slvsal1.gif

Pin Functions

PIN I/O DESCRIPTION
NAME NO.
EN 1 I Active-high enable input. Logic input. Connects to resistor divider.
ENSD 16 I Pull low to put device into low-current standby mode. Logic input.
FFLTb 9 O Active-low, open-drain FET fault indicator. Indicates shorted MOSFET when output is off.
FLTb 13 O Active-low, open-drain output indicates overload fault timer has turned MOSFET off.
GATE 10 O Gate driver output for external MOSFET
GND 4 – Ground
IMON 6 O Analog load current limit program point. Connect RIMON to ground.
LATCH 14 I Latch or retry mode select input. Latch when floating or connected to a logic-level voltage; retry when connected to GND.
OUT 8 I Output voltage sensor for monitoring MOSFET power.
OV 5 I Overvoltage comparator input. Connects to resistor divider. GATE is pulled low when OV exceeds the threshold.
PGb 15 O Active-low, open-drain power-good indicator. Status is determined by the voltage across the MOSFET.
PROG 2 I Power-limiting programming pin. A resistor from this pin to GND sets the maximum power dissipation for the FET.
SENSE 11 I Current-sensing input for resistor shunt from VCC to SENSE.
SET 7 I Current-limit programming set pin. A resistor is connected from this pin to VCC.
TIMER 3 I/O A capacitor connected from this pin to GND provides a fault timing function.
VCC 12 I Input-voltage sense and power supply
Thermal pad — — Tied to GND