SLLSFG3 May   2020 THVD1428

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
    1.     Device Images
      1.      Block Diagram
  4. Revision History
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 ESD Ratings - IEC Specifications
    4. 6.4 Recommended Operating Conditions
    5. 6.5 Thermal Information
    6. 6.6 Power Dissipation
    7. 6.7 Electrical Characteristics
    8. 6.8 Switching Characteristics
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1 Electrostatic Discharge (ESD) Protection
      2. 8.3.2 Electrical Fast Transient (EFT) Protection
      3. 8.3.3 Surge Protection
      4. 8.3.4 Failsafe Receiver
    4. 8.4 Device Functional Modes
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Data Rate and Bus Length
        2. 9.2.1.2 Stub Length
        3. 9.2.1.3 Bus Loading
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Driver
|VOD| Driver differential output voltage magnitude
RL = 60 Ω, -12 V ≤ Vtest ≤ 12 V, see Figure 7
1.5 3.5 V
|VOD| Driver differential output voltage magnitude RL = 60 Ω, -12 V ≤ Vtest ≤ 12 V, 4.5 V ≤ VCC ≤ 5.5 V, see Figure 7 2.1 V
|VOD| Driver differential output voltage magnitude RL = 100 Ω, see Figure 8 2 4 V
|VOD| Driver differential output voltage magnitude RL = 54 Ω, see Figure 8 1.5 3.5 V
Δ|VOD| Change in differential output voltage RL = 54 Ω, see Figure 8 -200 200 mV
VOC Common-mode output voltage 1 VCC / 2 3 V
ΔVOC(SS) Change in steady-state common-mode output voltage -200 200 mV
IOS Short-circuit output current DE = VCC, -7 V ≤ VO ≤ 12 V -250 250 mA
Receiver
II Bus input current DE = 0 V, VCC = 0 V or 5.5 V VI = 12 V 50 125 µA
VI = -7 V -100 -65 µA
VI = -12 V -150 -100 µA
VTH+ Positive-going input threshold voltage Over common-mode range of ±12 V See(1) -100 -20 mV
VTH- Negative-going input threshold voltage -200 -130 See(1) mV
VHYS Input hysteresis 30 mV
CA,B Input differential capacitance Measured between A and B, f = 1 MHz 220 pF
VOH Output high voltage IOH = -8 mA VCC – 0.4 VCC – 0.3 V
VOL Output low voltage IOL = 8 mA 0.2 0.4 V
IOZR Output high-impedance current VO = 0 V or VCC, RE = VCC -1 1 µA
Logic
IIN Input current (D, DE, RE) 4.5 V ≤ VCC ≤ 5.5 V -6.2 6.2 µA
Device
ICC Supply current (quiescent) Driver and receiver enabled RE = 0 V, DE = VCC, No load 2.4 3 mA
Driver enabled, receiver disabled RE = VCC, DE = VCC, No load 2 2.6 mA
Driver disabled, receiver enabled RE = 0 V, DE = 0V, No load 700 960 µA
Driver and receiver disabled RE = VCC, DE = 0 V, D = open, No load 0.1 2 µA
TSD Thermal shutdown temperature 170
Under any specific conditions, VTH+ is assured to be at least VHYS higher than VTH–.