ZHCSR55C June   1984  – October 2022 SN75176A

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Recommended Operating Conditions
    3. 6.3 Thermal Information
    4. 6.4 Dissipation Rating Table
    5. 6.5 Electrical Characteristics – Driver
    6. 6.6 Electrical Characteristics – Receiver
    7. 6.7 Switching Characteristics – Driver
    8. 6.8 Switching Characteristics – Receiver
    9. 6.9 Typical Characteristics
  7. 7 Parameter Measurement Information
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1 Driver
      2. 8.3.2 Receiver
    4. 8.4 Device Functional Modes
      1. 8.4.1 Device Powered
      2. 8.4.2 Device Unpowered
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Trademarks
    2. 10.2 Electrostatic Discharge Caution
    3. 10.3 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • D|8
  • P|8
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.6 Electrical Characteristics – Receiver

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETERTEST CONDITIONSMINTYP(1)MAXUNIT
VIT+Positive-going input threshold voltageVO = 2.7 V, IO = –0.4 mA0.2V
VIT–Negative-going input threshold voltageVO = 0.5 V, IO = 8 mA–0.2V
VhysInput hysteresis voltage (VIT+ – VIT-)50mV
VIKEnable clamp voltageII = –18 mA–1.5V
VOHHigh-level output voltageVID = 200 mV, IOH = –400 µA See Figure 7-22.7V
VOLLow-level output voltageVID = 200 mV, IOH = 8 mA See Figure 7-20.45V
IOZHigh-impedance-state output currentVO = 0.4 V to 2.4 V±20µA
IILine input currentOther input = 0 V(2)VI = 12 V1mA
VI = –7 V–0.8
IIHHigh-level enable input currentVIH = 2.7 V20µA
IILLow-level enable input currentVIL = 0.4 V–100µA
riInput resistance12kΩ
IOSShort-circuit output current–15–85mA
ICCSupply current (total package)No loadOutputs enabled3550mA
Outputs disabled2640
(1) All typical values are at VCC = 5 V, TA = 25°C.
(2) This applies for both power on and power off. Refer to ANSI Standard EIA/TIA-422-B for exact conditions.