ZHCSKS3C February   2020  – April 2024 TLV761

PRODMIX  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Dropout Voltage
      2. 6.3.2 Foldback Current Limit
      3. 6.3.3 Undervoltage Lockout (UVLO)
      4. 6.3.4 Thermal Shutdown
    4. 6.4 Device Functional Modes
      1. 6.4.1 Device Functional Mode Comparison
      2. 6.4.2 Normal Operation
      3. 6.4.3 Dropout Operation
  8. 7 Application and Implementation
    1. 7.1 Application Information
      1. 7.1.1 Recommended Capacitor Types
      2. 7.1.2 Input and Output Capacitor Requirements
      3. 7.1.3 Reverse Current
      4. 7.1.4 Power Dissipation (PD)
      5. 7.1.5 Estimating Junction Temperature
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
    3. 7.3 Best Design Practices
    4. 7.4 Power Supply Recommendations
    5. 7.5 Layout
      1. 7.5.1 Layout Guidelines
      2. 7.5.2 Layout Examples
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Device Nomenclature
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 接收文档更新通知
    4. 8.4 支持资源
    5. 8.5 Trademarks
    6. 8.6 静电放电警告
    7. 8.7 术语表
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.5 Electrical Characteristics

specified at TJ = –40°C to 125°C, VIN = VOUT(nom) + 1.5V or VIN = 2.5V (whichever is greater), IOUT = 10mA, CIN = 1.0µF and COUT = 1.0µF (unless otherwise noted); typical values are at TJ= 25ºC
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VOUT Nominal output accuracy TJ = 25°C –1 1 %
VOUT Output accuracy over temperature VIN ≥ 3.0V, VOUT(NOM) ≤ 9.0V, 1mA ≤ IOUT ≤ 1A –1.75 1.75 %
VOUT(NOM) > 9.0V, 1mA ≤ IOUT ≤ 1A –1.5 1.5
ΔVOUT(ΔVIN) Line regulation(1) VOUT(NOM) ≤ 9.0V, VOUT(NOM) + 1.5V ≤ VIN ≤ 16V, IOUT = 10mA 0.02 %/V
VOUT(NOM) > 9.0V, VOUT(NOM) + 1.5V ≤ VIN ≤ 16V, IOUT = 10mA 9.9 mV
ΔVOUT(ΔIOUT) Load regulation 1mA ≤ IOUT ≤ 1A, VIN ≥ 3.0V 0.1 0.75 %/A
VDO Dropout voltage(2) VIN ≥ 3.0V, IOUT = 1A 0.9 1.6 V
ICL Output current limit VOUT = 0.9 x VOUT(NOM), VIN ≥ 3.0V 1.1 1.6 A
ISC Short-circuit current limit VOUT = 0V 150 250 350 mA
IQ Quiescent current IOUT = 0mA  65 100 µA
IPULLDOWN Output pulldown current(3)  VIN = 1.8V, VOUT = 2.5V 0.7 1.1 mA
PSRR Power-supply rejection ratio VIN = 3.3V, VOUT = 1.8V, IOUT = 300mA, f = 120Hz 70 dB
Vn Output noise voltage BW = 10Hz to 100kHz, VIN = 3.3V, VOUT = 0.8V, IOUT = 100mA 60 µVRMS
VUVLO+ UVLO threshold rising VIN rising 2.2 2.4 V
VUVLO(HYS) UVLO hysteresis 130 mV
VUVLO- UVLO threshold falling VIN falling 1.9 V
TSD(shutdown) Thermal shutdown temperature Temperature increasing 180 ºC
TSD(reset) Thermal shutdown reset temperature Temperature falling 160 ºC
(1) Line regulation is measured with VIN = VOUT(NOM) + 1.5 V or 2.5 V (whichever is greater).
(2) VDO is measured with VIN = 95% x VOUT(nom) for fixed output devices. VDO is not measured for fixed output devices when VOUT < 2.5 V.
(3) IPULLDOWN is measured with VIN = 1.8 V (lower than UVLO falling threshold, with LDO in disabled state) and 2.5 V applied on VOUT externally.