ZHCSB70C June   2013  – January 2024 TCA9617A

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7.   Parameter Measurement Information
  8. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Bidirectional Level Translation
      2. 6.3.2 VOL B-side Offset Voltage
      3. 6.3.3 High to Low Transition Characteristics
    4. 6.4 Device Functional Modes
  9. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Standard Application
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
          1. 7.2.1.2.1 Pullup Resistor Sizing
        3. 7.2.1.3 Application Curves
      2. 7.2.2 Star Application
        1. 7.2.2.1 Design Requirements
        2. 7.2.2.2 Detailed Design Procedure
        3. 7.2.2.3 Application Curves
      3. 7.2.3 Series Application
        1. 7.2.3.1 Design Requirements
        2. 7.2.3.2 Detailed Design Procedure
        3. 7.2.3.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  10. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 支持资源
    3. 8.3 Trademarks
    4. 8.4 静电放电警告
    5. 8.5 术语表
  11. 9 Revision History
  12. 10Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

9 Revision History

Changes from Revision B (December 2018) to Revision C (January 2024)

  • 将提到的旧术语实例全部更改为控制器和目标Go
  • 将“器件信息”表更改为封装信息 表Go
  • 将说明 中的隔离 更改为分离 Go
  • 删除了“或更大的总线电容”Go
  • Added internal pull-up resistor information on EN pinGo
  • Changed abs max voltages from 7V to 6.5VGo
  • Changed the Thermal Information for 8 DGKGo
  • Changed VIK MAX value of -1.2V to a MIN valueGo
  • Changed TPLH (B to A) by removing typical value.Go
  • Changed TPLH (A to B) for VCCB ≤ 3V by changing min value from 59ns to 50ns and removing typical valueGo
  • Changed TPLH (A to B) for VCCB > 3V by removing typical valueGo
  • Changed TPHL (B to A) by changing min value from 69ns to 32ns and removing typical valueGo
  • Changed TPHL (A to B) by changing min value from 68ns to 28ns and removing typical valueGo
  • Changed TTHL (B side) by changing max value from 13.8ns to 32ns and removing typical valueGo
  • Changed TTHL (B side) by changing max value from 11.3ns to 40ns and removing typical valueGo
  • Changed 0.3VCCA to: 30% of VCCA in the Overview Go
  • Changed A side falling below 0.7VCCA to: A side falling below 30% of VCCA Go
  • Changed goes below 0.7VCCB to: goes below 0.4V Go
  • Changed "70mV or more below the output low level" to: goes below VIL Go
  • Changed 0.3VCCA to: 30% of VCCA in the Low to High Transition Characteristics Go
  • Changed "accelerator thresholds are below 30% of VCCB" to: "overshoot is more than accelerator thresholds"Go
  • Deleted Since the A-side does not have a static offset low voltage, no pedestal is seen on the A-side as shown in Bus A (0.8V to 5.5V Bus) Waveform Go
  • Changed 0.7VCCA to 30% of VCCA in the High-to-Low Transition Characteristics Go
  • Changed isolate a badly behaved to separate a misbehaving in the Device Functional Modes Go
  • Changed 0.7VCCA to 30% of VCCA in the Application Information Go
  • Changed falls below 0.45V to: falls below 0.4V Go
  • Changed (0.45V) to: (0.4V) in the Pullup Resistor Sizing Go

Changes from Revision A (July 2014) to Revision B (December 2018)

  • Changed the appearance of the DGK pin out image Go
  • Deleted VCCA < VCCB from the Design Requirements listGo

Changes from Revision * (June 2013) to Revision A (July 2014)

  • 从“特性”列表中删除了“断电高阻抗 I2C 引脚”Go
  • 添加了“应用”Go
  • Added Typical Characteristics section. Go
  • Added Application and Implementation section. Go
  • Added Power Supply Recommendations section. Go