ZHCSFI6E September   2015  – February 2017 DRV3205-Q1

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Serial Peripheral Interface Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Programming
      1. 7.3.1 SPI
        1. 7.3.1.1 Address Mode Transfer
          1. 7.3.1.1.1 SPI Address Transfer Phase
        2. 7.3.1.2 SPI Data Transfer Phase
        3. 7.3.1.3 Device Data Response
    4. 7.4 Register Maps
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Three-Phase Motor Drive-Device for Automotive Application
    3. 8.3 System Example
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 文档支持
      1. 11.1.1 相关文档
    2. 11.2 接收文档更新通知
    3. 11.3 社区资源
    4. 11.4 商标
    5. 11.5 静电放电警告
    6. 11.6 Glossary
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

4 修订历史记录

Changes from D Revision (November 2016) to E Revision

  • Added the propagation delay graphs to the Typical Characteristics sectionGo
  • Changed the note on the Single 8-Bit SPI Frame/Transfer figureGo
  • Updated the Typical Application Diagram figureGo

Changes from C Revision (October 2016) to D Revision

  • Changed the maximum value for the RVSET resistor error detection parameter (4.4.31) from 1.5 to 1.4 kΩ in the Electrical Characteristics tableGo
  • Changed the units and symbol for the RVSET output voltage parameter (4.4.32–4.4.34), and fixed duplicate position number for TJ = 25°C and 125°C in the Electrical Characteristics tableGo
  • Added characterization note to parameters 5.7 and 5.29 through 5.30e in the Electrical Characteristics tableGo
  • Deleted the VS voltage range test condition from the boost output voltage parameter (6.1) in the Electrical Characteristics table Go
  • Added new test condition to the switching frequency parameter (6.3) and add new values for switching frequency at VS < 6 (6.31) in the Electrical Characteristics tableGo
  • Changed the maximum value for the input pulldown resistor at EN pin parameter (7.4) from 300 to 360 kΩ in the Electrical Characteristics tableGo
  • Changed the position number for the output high and low voltage 2 parameters in the Electrical Characteristics table Go
  • Added characterization note to parameters 13.2 through 13.11 in the Serial Peripheral Interface Timing Requirements tableGo

Changes from B Revision (October 2016) to C Revision

  • Clarified the temperature for the BOOST pin quiescent current parameters (3.6B and 3.6C) and added new temperature condition (3.62B and 3.61C) in the Recommended Operating Conditions tableGo
  • Deleted the maximum value for the input hysteresis parameters (7.3 and 7.3A) in the Electrical Characteristics tableGo
  • Changed the values for the input pullup resistance parameter (7.5) in the Electrical Characteristics tableGo

Changes from A Revision (October 2016) to B Revision

  • Changed 已将特性部分的 AEC-Q1100 改为 AEC-Q100Go
  • Changed the maximum value for the VCC5 and VCC3 short-to-ground current from 70 to 80 mA in the Absolute Maximum Ratings tableGo
  • Changed the minimum value for the high-side/low-side driver shutdown current parameter from 7 to 2 mA in the Electrical Characteristics tableGo

Changes from * Revision (September 2016) to A Revision

  • Changed 器件状态，从产品预览改为量产数据Go